| Age | Commit message (Collapse) | Author |
|---|
|
The mirroring tests are currently run in a skip_hw and optionally a skip_sw
mode. The former tests the SW datapath, the latter the HW datapath, if
available. In order to be able to test SW datapath on HW loopbacks, traps
are installed on ingress to get traffic from the HW datapath to the SW one.
This adds an unnecessary complexity when it would be much simpler to just
use a veth-based topology to test the SW datapath. Thus drop all the code
that supports this dual testing.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.
The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.
However, often the counter tap is installed at the remote end of the gretap
tunnel. Since this is a SW-datapath scenario anyway, we can make the filter
arbitrarily accurate.
Thus in this patch, add parameters forward_type and backward_type to
several mirroring test helpers, as some other helpers already have. Then
change do_test_span_dir_ips() to instead of installing one generic tap and
using it for test in both directions, install the tap for each direction
separately, matching on the ICMP type given by these parameters.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The argument is not used by these functions except to propagate it for
ultimately no purpose.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.
So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.
For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.
Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having a clsact qdisc on $h3 is useful in several tests, and will be
useful in more tests to come. Move the registration from all the tests
that need it into the topology file itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit a511858c7536 ("selftests: fib_tests: Allow user to run
a specific test"), allow user to run only a subset of the tests using
the TESTS environment variable.
This is useful when not all the tests can pass on a given system.
Example:
# export TESTS="ping_ipv4 ping_ipv6"
# ./bridge_vlan_aware.sh
TEST: ping [PASS]
TEST: ping6 [PASS]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test for basic mirroring to gretap and ip6gretap netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
