| Age | Commit message (Collapse) | Author |
|---|
|
commit f8cc59ecc22841be5deb07b549c0c6a2657cd5f9 upstream.
Add the following Telit Cinterion FN990A MBIM composition:
0x1074: MBIM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (diag) +
DPL (Data Packet Logging) + adb
T: Bus=01 Lev=01 Prnt=04 Port=06 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1074 Rev=05.04
S: Manufacturer=Telit Wireless Solutions
S: Product=FN990
S: SerialNumber=70628d0c
C: #Ifs= 8 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b84cc80610a8ce036deb987f056ce3196ead7f1e upstream.
When a port is disabled, an attached device will be disconnected. This
causes a port-status-change event, which will race with hub autosuspend
(if the disabled port was the only connected port on its hub), causing
an immediate resume and a second autosuspend. Both of these can be
avoided by adding a short delay after the call to
usb_hub_set_port_power().
Below log shows what is happening:
$ echo 1 > usb1-port1/disable
[ 37.958239] usb 1-1: USB disconnect, device number 2
[ 37.964101] usb 1-1: unregistering device
[ 37.970070] hub 1-0:1.0: hub_suspend
[ 37.971305] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 37.974412] usb usb1: bus auto-suspend, wakeup 1
[ 37.988175] usb usb1: suspend raced with wakeup event <---
[ 37.993947] usb usb1: usb auto-resume
[ 37.998401] hub 1-0:1.0: hub_resume
[ 38.105688] usb usb1-port1: status 0000, change 0000, 12 Mb/s
[ 38.112399] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 38.118645] hub 1-0:1.0: hub_suspend
[ 38.122963] usb usb1: bus auto-suspend, wakeup 1
[ 38.200368] usb usb1: usb wakeup-resume
[ 38.204982] usb usb1: usb auto-resume
[ 38.209376] hub 1-0:1.0: hub_resume
[ 38.213676] usb usb1-port1: status 0101 change 0001
[ 38.321552] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 38.327978] usb usb1-port1: status 0101, change 0000, 12 Mb/s
[ 38.457429] usb 1-1: new high-speed USB device number 3 using ci_hdrc
Then, port change bit will be fixed to the final state and
usb_clear_port_feature() can correctly clear it after this period. This
will also avoid usb runtime suspend routine to run because
usb_autopm_put_interface() not run yet.
Fixes: f061f43d7418 ("usb: hub: port: add sysfs entry to switch port power")
Cc: stable@kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260316095042.1559882-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81ebd43cc0d6d106ce7b6ccbf7b5e40ca7f5503d upstream.
When calling unbind, then bind again, cdev_init reinitialized the cdev,
even though there may still be references to it. That's the case when
the /dev/hidg* device is still opened. This obviously unsafe behavior
like oopes.
This fixes this by using cdev_alloc to put the cdev on the heap. That
way, we can simply allocate a new one in hidg_bind.
Closes: https://lore.kernel.org/linux-usb/CAN9vWDKZn0Ts5JyV2_xcAmbnBEi0znMLg_USMFrShRryXrgWGQ@mail.gmail.com/T/#m2cb0dba3633b67b2a679c98499508267d1508881
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Link: https://patch.msgid.link/20260327192209.59945-1-sigmaepsilon92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f58752ebcb35e156c85cd1a82d6579c7af3b9023 upstream.
The Lenovo Yoga Book 9 14IAH10 (83KJ) has a composite USB device
(17EF:6161) that controls both touchscreens via a CDC ACM interface.
Interface 0 is a standard CDC ACM control interface, but interface 1
(the data interface) incorrectly declares vendor-specific class (0xFF)
instead of USB_CLASS_CDC_DATA. cdc-acm rejects the device at probe with
-EINVAL, leaving interface 0 unbound and EP 0x82 never polled.
With no consumer polling EP 0x82, the firmware's watchdog fires every
~20 seconds and resets the USB bus, producing a continuous disconnect/
reconnect loop that prevents the touchscreens from ever initialising.
Add two new quirk flags:
VENDOR_CLASS_DATA_IFACE: Bypasses the bInterfaceClass check in
acm_probe() that would otherwise reject the vendor-class data
interface with -EINVAL.
ALWAYS_POLL_CTRL: Submits the notification URB at probe() rather than
waiting for a TTY open. This keeps EP 0x82 polled at all times,
permanently suppressing the firmware watchdog. The URB is resubmitted
after port_shutdown() and on system resume. SET_CONTROL_LINE_STATE
(DTR|RTS) is sent at probe and after port_shutdown() to complete
firmware handshake.
Note: the firmware performs exactly 4 USB connect/disconnect cycles
(~19 s each) on every cold boot before stabilising. This is a fixed
firmware property; touch is available ~75-80 s after power-on.
Signed-off-by: Dave Carey <carvsdriver@gmail.com>
Cc: stable <stable@kernel.org>
Tested-by: Dave Carey <carvsdriver@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260402182950.389016-1-carvsdriver@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 609865ab3d5d803556f628e221ecd3d06aed9f30 upstream.
Expands range of matched bcdDevice values for the VL817 quirk entry.
This is based on experience with Axagon EE35-GTR rev1 3.5" HDD
enclosure, which reports its bcdDevice as 0x0843, but presumably other
vendors using this IC in their products may set it to any other value.
Signed-off-by: Daniel Brát <danek.brat@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260402172433.5227-1-danek.brat@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b9db53197094f38a18797495df2e3c758ec51dc upstream.
FUSB302 fails to probe with -EINVAL if its interrupt line is connected via
an I2C GPIO expander, such as TI TCA6416.
Switch the interrupt handler to a threaded one, which also works behind
such GPIO expanders.
Cc: stable <stable@kernel.org>
Fixes: 309b6341d557 ("usb: typec: fusb302: Revert incorrect threaded irq fix")
Signed-off-by: Alexey Charkov <alchark@flipper.net>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Heikki Krogerus <heikki.krogrerus@linux.intel.com>
Link: https://patch.msgid.link/20260317-fusb302-irq-v2-1-dbabd5c5c961@flipper.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ab833a16a825373aad2ba7d54b572b277e95b71 upstream.
When a USB/IP client receives a RET_SUBMIT response,
usbip_pack_ret_submit() unconditionally overwrites
urb->number_of_packets from the network PDU. This value is
subsequently used as the loop bound in usbip_recv_iso() and
usbip_pad_iso() to iterate over urb->iso_frame_desc[], a flexible
array whose size was fixed at URB allocation time based on the
*original* number_of_packets from the CMD_SUBMIT.
A malicious USB/IP server can set number_of_packets in the response
to a value larger than what was originally submitted, causing a heap
out-of-bounds write when usbip_recv_iso() writes to
urb->iso_frame_desc[i] beyond the allocated region.
KASAN confirmed this with kernel 7.0.0-rc5:
BUG: KASAN: slab-out-of-bounds in usbip_recv_iso+0x46a/0x640
Write of size 4 at addr ffff888106351d40 by task vhci_rx/69
The buggy address is located 0 bytes to the right of
allocated 320-byte region [ffff888106351c00, ffff888106351d40)
The server side (stub_rx.c) and gadget side (vudc_rx.c) already
validate number_of_packets in the CMD_SUBMIT path since commits
c6688ef9f297 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle
malicious input") and b78d830f0049 ("usbip: fix vudc_rx: harden
CMD_SUBMIT path to handle malicious input"). The server side validates
against USBIP_MAX_ISO_PACKETS because no URB exists yet at that point.
On the client side we have the original URB, so we can use the tighter
bound: the response must not exceed the original number_of_packets.
This mirrors the existing validation of actual_length against
transfer_buffer_length in usbip_recv_xbuff(), which checks the
response value against the original allocation size.
Kelvin Mbogo's series ("usb: usbip: fix integer overflow in
usbip_recv_iso()", v2) hardens the receive-side functions themselves;
this patch complements that work by catching the bad value at its
source -- in usbip_pack_ret_submit() before the overwrite -- and
using the tighter per-URB allocation bound rather than the global
USBIP_MAX_ISO_PACKETS limit.
Fix this by checking rpdu->number_of_packets against
urb->number_of_packets in usbip_pack_ret_submit() before the
overwrite. On violation, clamp to zero so that usbip_recv_iso() and
usbip_pad_iso() safely return early.
Fixes: 1325f85fa49f ("staging: usbip: bugfix add number of packets for isochronous frames")
Cc: stable <stable@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Nathan Rebello <nathan.c.rebello@gmail.com>
Link: https://patch.msgid.link/20260402085259.234-1-nathan.c.rebello@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f880aac8a57ebd92abfa685d45424b2998ac1059 upstream.
The GET_STATUS and SET/CLEAR_FEATURE handlers extract the endpoint
number from the host-supplied wIndex without any sort of validation.
Fix this up by validating the number of endpoints actually match up with
the number the device has before attempting to dereference a pointer
based on this math.
This is just like what was done in commit ee0d382feb44 ("usb: gadget:
aspeed_udc: validate endpoint index for ast udc") for the aspeed driver.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Link: https://patch.msgid.link/2026040647-sincerity-untidy-b104@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c088d5dd2fffb4de1fb8e7f57751c8b82942180a upstream.
A broken/bored/mean USB host can overflow the skb_shared_info->frags[]
array on a Linux gadget exposing a Phonet function by sending an
unbounded sequence of full-page OUT transfers.
pn_rx_complete() finalizes the skb only when req->actual < req->length,
where req->length is set to PAGE_SIZE by the gadget. If the host always
sends exactly PAGE_SIZE bytes per transfer, fp->rx.skb will never be
reset and each completion will add another fragment via
skb_add_rx_frag(). Once nr_frags exceeds MAX_SKB_FRAGS (default 17),
subsequent frag stores overwrite memory adjacent to the shinfo on the
heap.
Drop the skb and account a length error when the frag limit is reached,
matching the fix applied in t7xx by commit f0813bcd2d9d ("net: wwan:
t7xx: fix potential skb->frags overflow in RX path").
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Link: https://patch.msgid.link/2026040705-fruit-unloved-0701@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f993d30b95dc9557a8a96ceca11abed674c8acb upstream.
The block_len read from the host-supplied NTB header is checked against
ntb_max but has no lower bound. When block_len is smaller than
opts->ndp_size, the bounds check of:
ndp_index > (block_len - opts->ndp_size)
will underflow producing a huge unsigned value that ndp_index can never
exceed, defeating the check entirely.
The same underflow occurs in the datagram index checks against block_len
- opts->dpe_size. With those checks neutered, a malicious USB host can
choose ndp_index and datagram offsets that point past the actual
transfer, and the skb_put_data() copies adjacent kernel memory into the
network skb.
Fix this by rejecting block lengths that cannot hold at least the NTB
header plus one NDP. This will make block_len - opts->ndp_size and
block_len - opts->dpe_size both well-defined.
Commit 8d2b1a1ec9f5 ("CDC-NCM: avoid overflow in sanity checking") fixed
a related class of issues on the host side of NCM.
Fixes: 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: stable <stable@kernel.org>
Assisted-by: gregkh_clanker_t1000
Link: https://patch.msgid.link/2026040753-baffle-handheld-624d@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Notifications can arrive before ucsi_init() has populated
ucsi->cap.num_connectors via GET_CAPABILITY. At that point
num_connectors is still 0, causing all valid connector numbers to be
incorrectly rejected as bogus.
Skip the bounds check when num_connectors is 0 (not yet initialized).
Pre-init notifications are already handled safely by the early-event
guard in ucsi_connector_change().
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: d2d8c17ac01a ("usb: typec: ucsi: validate connector number in ucsi_notify_common()")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Rebello <nathan.c.rebello@gmail.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260407063958.863-1-nathan.c.rebello@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB serial device ids for 7.0-rc7
Here are some new modem and io_edgeport device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-7.0-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add MeiG Smart SRM825WN
USB: serial: io_edgeport: add support for Blackbox IC135A
USB: serial: option: add support for Rolling Wireless RW135R-GL
|
|
There was an issue when you did the following:
- setup and bind an hid gadget
- open /dev/hidg0
- use the resulting fd in EPOLL_CTL_ADD
- unbind the UDC
- bind the UDC
- use the fd in EPOLL_CTL_DEL
When CONFIG_DEBUG_LIST was enabled, a list_del corruption was reported
within remove_wait_queue (via ep_remove_wait_queue). After some
debugging I found out that the queues, which f_hid registers via
poll_wait were the problem. These were initialized using
init_waitqueue_head inside hidg_bind. So effectively, the bind function
re-initialized the queues while there were still items in them.
The solution is to move the initialization from hidg_bind to hidg_alloc
to extend their lifetimes to the lifetime of the function instance.
Additionally, I found many other possibly problematic init calls in the
bind function, which I moved as well.
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260331184844.2388761-1-sigmaepsilon92@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove usb_offload_get() and usb_offload_put() from the xHCI sideband
interrupter creation and removal paths.
The responsibility of manipulating offload_usage now lies entirely with
the USB class drivers. They have the precise context of when an offload
data stream actually starts and stops, ensuring a much more accurate
representation of offload activity for power management.
Cc: stable <stable@kernel.org>
Fixes: ef82a4803aab ("xhci: sideband: add api to trace sideband usage")
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Tested-by: Hailong Liu <hailong.liu@oppo.com>
Tested-by: hailong.liu@oppo.com
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260401123238.3790062-3-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the coarse USB device lock with a dedicated offload_lock
spinlock to reduce contention during offload operations. Use
offload_pm_locked to synchronize with PM transitions and replace
the legacy offload_at_suspend flag.
Optimize usb_offload_get/put by switching from auto-resume/suspend
to pm_runtime_get_if_active(). This ensures offload state is only
modified when the device is already active, avoiding unnecessary
power transitions.
Cc: stable <stable@kernel.org>
Fixes: ef82a4803aab ("xhci: sideband: add api to trace sideband usage")
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Tested-by: Hailong Liu <hailong.liu@oppo.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260401123238.3790062-2-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When cdns3_gadget_start() fails, the DRD hardware is left in gadget mode
while software state remains INACTIVE, creating hardware/software state
inconsistency.
When switching to host mode via sysfs:
echo host > /sys/class/usb_role/13180000.usb-role-switch/role
The role state is not set to CDNS_ROLE_STATE_ACTIVE due to the error,
so cdns_role_stop() skips cleanup because state is still INACTIVE.
This violates the DRD controller design specification (Figure22),
which requires returning to idle state before switching roles.
This leads to a synchronous external abort in xhci_gen_setup() when
setting up the host controller:
[ 516.440698] configfs-gadget 13180000.usb: failed to start g1: -19
[ 516.442035] cdns-usb3 13180000.usb: Failed to add gadget
[ 516.443278] cdns-usb3 13180000.usb: set role 2 has failed
...
[ 1301.375722] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 1301.377716] Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP
[ 1301.382485] pc : xhci_gen_setup+0xa4/0x408
[ 1301.393391] backtrace:
...
xhci_gen_setup+0xa4/0x408 <-- CRASH
xhci_plat_setup+0x44/0x58
usb_add_hcd+0x284/0x678
...
cdns_role_set+0x9c/0xbc <-- Role switch
Fix by calling cdns_drd_gadget_off() in the error path to properly
clean up the DRD gadget state.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongchao Wu <yongchao.wu@autochips.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260401001000.5761-1-yongchao.wu@autochips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When platform_get_drvdata() returns NULL and probe defers, the error
path jumps to the 'depopulate' label, skipping put_device() for the
reference acquired by of_find_device_by_node(). This extra reference
prevents the child platform device from being freed when
of_platform_depopulate() is called, resulting in memory leaks reported
by kmemleak:
unreferenced object 0xffff0000c92c1480 (size 64):
comm "kworker/u16:2", pid 50, jiffies 4294895789
backtrace (crc 49d507d0):
kmemleak_alloc+0x34/0x40
__kmalloc_noprof+0x430/0x670
of_device_alloc+0xec/0x26c
of_platform_device_create_pdata+0x60/0x1f0
of_platform_bus_create+0x290/0x610
of_platform_populate+0x74/0x118
dwc3_imx8mp_probe+0x228/0x734
Fixes: 86767625f525 ("usb: dwc3: imx8mp: disable auto suspend for host role")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260401134938.686748-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
f_audio_complete() copies req->length bytes into a 4-byte stack
variable:
u32 data = 0;
memcpy(&data, req->buf, req->length);
req->length is derived from the host-controlled USB request path,
which can lead to a stack out-of-bounds write.
Validate req->actual against the expected payload size for the
supported control selectors and decode only the expected amount
of data.
This avoids copying a host-influenced length into a fixed-size
stack object.
Signed-off-by: Taegu Ha <hataegu0826@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260401191311.3604898-1-hataegu0826@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When device_register() fails, ulpi_register() calls put_device() on
ulpi->dev.
The device release callback ulpi_dev_release() drops the OF node
reference and frees ulpi, but the current error path in
ulpi_register_interface() then calls kfree(ulpi) again, causing a
double free.
Let put_device() handle the cleanup through ulpi_dev_release() and
avoid freeing ulpi again in ulpi_register_interface().
Fixes: 289fcff4bcdb1 ("usb: add bus type for USB ULPI")
Cc: stable <stable@kernel.org>
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260401025142.1398996-1-lgs201920130244@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_submit_urb() fails in usbio_probe(), the previously allocated
URB is never freed, causing a memory leak.
Fix this by jumping to err_free_urb label to properly release the URB
on the error path.
Fixes: 121a0f839dbb ("usb: misc: Add Intel USBIO bridge driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Link: https://patch.msgid.link/20260331-usbio-v2-1-d8c48dad9463@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Razer Kiyo Pro (1532:0e05) is a USB 3.0 UVC webcam whose firmware
does not handle USB Link Power Management transitions reliably. When LPM
is active, the device can enter a state where it fails to respond to
control transfers, producing EPIPE (-32) errors on UVC probe control
SET_CUR requests. In the worst case, the stalled endpoint triggers an
xHCI stop-endpoint command that times out, causing the host controller
to be declared dead and every USB device on the bus to be disconnected.
This has been reported as Ubuntu Launchpad Bug #2061177. The failure
mode is:
1. UVC probe control SET_CUR returns -32 (EPIPE)
2. xHCI host not responding to stop endpoint command
3. xHCI host controller not responding, assume dead
4. All USB devices on the affected xHCI controller disconnect
Disabling LPM prevents the firmware from entering the problematic low-
power states that precede the stall. This is the same approach used for
other webcams with similar firmware issues (e.g., Logitech HD Webcam C270).
Cc: stable <stable@kernel.org>
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2061177
Signed-off-by: JP Hein <jp@jphein.com>
Link: https://patch.msgid.link/20260331003806.212565-2-jp@jphein.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the gadget endpoint is disabled or not yet configured, the ep->desc
pointer can be NULL. This leads to a NULL pointer dereference when
__cdns3_gadget_ep_queue() is called, causing a kernel crash.
Add a check to return -ESHUTDOWN if ep->desc is NULL, which is the
standard return code for unconfigured endpoints.
This prevents potential crashes when ep_queue is called on endpoints
that are not ready.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongchao Wu <yongchao.wu@autochips.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260331000407.613298-1-yongchao.wu@autochips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 53a2d95df836 ("usb: core: add phy notify connect and disconnect")
causes double use of the 'usb3-phy' in certain cases.
Since that commit, if a generic PHY named 'usb3-phy' is specified in
the device tree, that is getting added to the 'phy_roothub' list of the
secondary HCD by the usb_phy_roothub_alloc_usb3_phy() function. However,
that PHY is getting added also to the primary HCD's 'phy_roothub' list
by usb_phy_roothub_alloc() if there is no generic PHY specified with
'usb2-phy' name.
This causes that the usb_add_hcd() function executes each phy operations
twice on the 'usb3-phy'. Once when the primary HCD is added, then once
again when the secondary HCD is added.
The issue affects the Marvell Armada 3700 platform at least, where a
custom name is used for the USB2 PHY:
$ git grep 'phy-names.*usb3' arch/arm64/boot/dts/marvell/armada-37xx.dtsi | tr '\t' ' '
arch/arm64/boot/dts/marvell/armada-37xx.dtsi: phy-names = "usb3-phy", "usb2-utmi-otg-phy";
Extend the usb_phy_roothub_alloc_usb3_phy() function to skip adding the
'usb3-phy' to the 'phy_roothub' list of the secondary HCD when 'usb2-phy'
is not specified in the device tree to avoid the double use.
Fixes: 53a2d95df836 ("usb: core: add phy notify connect and disconnect")
Cc: stable <stable@kernel.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20260330-usb-avoid-usb3-phy-double-use-v1-1-d2113aecb535@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the SDX62-based MeiG Smart SRM825WN module.
If#= 0: RNDIS
If#= 1: RNDIS
If#= 2: Diag
If#= 3: AT
If#= 4: AT
If#= 5: NMEA
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 19 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2dee ProdID=4d38 Rev= 5.04
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=da47a175
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Ernestas Kulik <ernestas.k@iconn-networks.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The net_device is allocated during function instance creation and
registered during the bind phase with the gadget device as its sysfs
parent. When the function unbinds, the parent device is destroyed, but
the net_device survives, resulting in dangling sysfs symlinks:
console:/ # ls -l /sys/class/net/usb0
lrwxrwxrwx ... /sys/class/net/usb0 ->
/sys/devices/platform/.../gadget.0/net/usb0
console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0
ls: .../gadget.0/net/usb0: No such file or directory
Use device_move() to reparent the net_device between the gadget device
tree and /sys/devices/virtual across bind and unbind cycles. During the
final unbind, calling device_move(NULL) moves the net_device to the
virtual device tree before the gadget device is destroyed. On rebinding,
device_move() reparents the device back under the new gadget, ensuring
proper sysfs topology and power management ordering.
To maintain compatibility with legacy composite drivers (e.g., multi.c),
the borrowed_net flag is used to indicate whether the network device is
shared and pre-registered during the legacy driver's bind phase.
Fixes: f466c6353819 ("usb: gadget: f_rndis: convert to new function interface with backward compatibility")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-7-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The net_device is allocated during function instance creation and
registered during the bind phase with the gadget device as its sysfs
parent. When the function unbinds, the parent device is destroyed, but
the net_device survives, resulting in dangling sysfs symlinks:
console:/ # ls -l /sys/class/net/usb0
lrwxrwxrwx ... /sys/class/net/usb0 ->
/sys/devices/platform/.../gadget.0/net/usb0
console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0
ls: .../gadget.0/net/usb0: No such file or directory
Use device_move() to reparent the net_device between the gadget device
tree and /sys/devices/virtual across bind and unbind cycles. During the
final unbind, calling device_move(NULL) moves the net_device to the
virtual device tree before the gadget device is destroyed. On rebinding,
device_move() reparents the device back under the new gadget, ensuring
proper sysfs topology and power management ordering.
To maintain compatibility with legacy composite drivers (e.g., multi.c),
the bound flag is used to indicate whether the network device is shared
and pre-registered during the legacy driver's bind phase.
Fixes: 8cedba7c73af ("usb: gadget: f_subset: convert to new function interface with backward compatibility")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-6-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The net_device is allocated during function instance creation and
registered during the bind phase with the gadget device as its sysfs
parent. When the function unbinds, the parent device is destroyed, but
the net_device survives, resulting in dangling sysfs symlinks:
console:/ # ls -l /sys/class/net/usb0
lrwxrwxrwx ... /sys/class/net/usb0 ->
/sys/devices/platform/.../gadget.0/net/usb0
console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0
ls: .../gadget.0/net/usb0: No such file or directory
Use device_move() to reparent the net_device between the gadget device
tree and /sys/devices/virtual across bind and unbind cycles. During the
final unbind, calling device_move(NULL) moves the net_device to the
virtual device tree before the gadget device is destroyed. On rebinding,
device_move() reparents the device back under the new gadget, ensuring
proper sysfs topology and power management ordering.
To maintain compatibility with legacy composite drivers (e.g., multi.c),
the bound flag is used to indicate whether the network device is shared
and pre-registered during the legacy driver's bind phase.
Fixes: b29002a15794 ("usb: gadget: f_eem: convert to new function interface with backward compatibility")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-5-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The net_device is allocated during function instance creation and
registered during the bind phase with the gadget device as its sysfs
parent. When the function unbinds, the parent device is destroyed, but
the net_device survives, resulting in dangling sysfs symlinks:
console:/ # ls -l /sys/class/net/usb0
lrwxrwxrwx ... /sys/class/net/usb0 ->
/sys/devices/platform/.../gadget.0/net/usb0
console:/ # ls -l /sys/devices/platform/.../gadget.0/net/usb0
ls: .../gadget.0/net/usb0: No such file or directory
Use device_move() to reparent the net_device between the gadget device
tree and /sys/devices/virtual across bind and unbind cycles. During the
final unbind, calling device_move(NULL) moves the net_device to the
virtual device tree before the gadget device is destroyed. On rebinding,
device_move() reparents the device back under the new gadget, ensuring
proper sysfs topology and power management ordering.
To maintain compatibility with legacy composite drivers (e.g., multi.c),
the bound flag is used to indicate whether the network device is shared
and pre-registered during the legacy driver's bind phase.
Fixes: fee562a6450b ("usb: gadget: f_ecm: convert to new function interface with backward compatibility")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-4-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Provide kernel-doc descriptions for the fields in struct f_ncm_opts to
improve code readability and maintainability.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-3-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The class/subclass/protocol options are suspectible to race conditions
as they can be accessed concurrently through configfs.
Use existing mutex to protect these options. This issue was identified
during code inspection.
Fixes: 73517cf49bd4 ("usb: gadget: add RNDIS configfs options for class/subclass/protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-2-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
geth_alloc() increments the reference count, but geth_free() fails to
decrement it. This prevents the configuration of attributes via configfs
after unlinking the function.
Decrement the reference count in geth_free() to ensure proper cleanup.
Fixes: 02832e56f88a ("usb: gadget: f_subset: add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260320-usb-net-lifecycle-v1-1-4886b578161b@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the current implementation, if a cable's alternate mode enter operation
is not supported, the tbt->plug[TYPEC_PLUG_SOP_P] pointer is cleared by the
time tbt_enter_mode() is called. This prevents the driver from identifying
the cable's VDO.
As a result, the Thunderbolt connection falls back to the default
TBT_CABLE_USB3_PASSIVE speed, even if the cable supports higher speeds.
To ensure the correct VDO value is used during mode entry, calculate and
store the enter_vdo earlier during the initialization phase in tbt_ready().
Cc: stable <stable@kernel.org>
Fixes: 100e25738659 ("usb: typec: Add driver for Thunderbolt 3 Alternate Mode")
Tested-by: Madhu M <madhu.m@intel.corp-partner.google.com>
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20260324103012.1417616-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The typec plug alternate mode is already registered as part of the bus.
When both class and bus are set for a device, device_add() attempts to
create the "subsystem" symlink in the device's sysfs directory twice, once
for the bus and once for the class.
This results in a duplicate filename error during registration,
causing the alternate mode registration to fail with warnings:
cannot create duplicate filename '/devices/pci0000:00/0000:00:1f.0/
PNP0C09:00/GOOG0004:00/cros-ec-dev.1.auto/cros_ec_ucsi.3.auto/typec/
port1/port1-cable/port1-plug0/port1-plug0.0/subsystem'
typec port0-plug0: failed to register alternate mode (-17)
cros_ec_ucsi.3.auto: failed to registers svid 0x8087 mode 1
Cc: stable <stable@kernel.org>
Fixes: 67ab45426215 ("usb: typec: Set the bus also for the port and plug altmodes")
Tested-by: Madhu M <madhu.m@intel.corp-partner.google.com>
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20260324102903.1416210-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dwc2_gadget_exit_clock_gating() internally calls call_gadget() macro,
which expects hsotg->lock to be held since it does spin_unlock/spin_lock
around the gadget driver callback invocation.
However, dwc2_hsotg_udc_stop() calls dwc2_gadget_exit_clock_gating()
without holding the lock. This leads to:
- spin_unlock on a lock that is not held (undefined behavior)
- The lock remaining held after dwc2_gadget_exit_clock_gating() returns,
causing a deadlock when spin_lock_irqsave() is called later in the
same function.
Fix this by acquiring hsotg->lock before calling
dwc2_gadget_exit_clock_gating() and releasing it afterwards, which
satisfies the locking requirement of the call_gadget() macro.
Fixes: af076a41f8a2 ("usb: dwc2: also exit clock_gating when stopping udc while suspended")
Cc: stable <stable@kernel.org>
Signed-off-by: Juno Choi <juno.choi@lge.com>
Link: https://patch.msgid.link/20260324014910.2798425-1-juno.choi@lge.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit b81ac4395bbe ("usb: gadget: uvc: allow for application to cleanly
shutdown") introduced two stages of synchronization waits totaling 1500ms
in uvc_function_unbind() to prevent several types of kernel panics.
However, this timing-based approach is insufficient during power
management (PM) transitions.
When the PM subsystem starts freezing user space processes, the
wait_event_interruptible_timeout() is aborted early, which allows the
unbind thread to proceed and nullify the gadget pointer
(cdev->gadget = NULL):
[ 814.123447][ T947] configfs-gadget.g1 gadget.0: uvc: uvc_function_unbind()
[ 814.178583][ T3173] PM: suspend entry (deep)
[ 814.192487][ T3173] Freezing user space processes
[ 814.197668][ T947] configfs-gadget.g1 gadget.0: uvc: uvc_function_unbind no clean disconnect, wait for release
When the PM subsystem resumes or aborts the suspend and tasks are
restarted, the V4L2 release path is executed and attempts to access the
already nullified gadget pointer, triggering a kernel panic:
[ 814.292597][ C0] PM: pm_system_irq_wakeup: 479 triggered dhdpcie_host_wake
[ 814.386727][ T3173] Restarting tasks ...
[ 814.403522][ T4558] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000030
[ 814.404021][ T4558] pc : usb_gadget_deactivate+0x14/0xf4
[ 814.404031][ T4558] lr : usb_function_deactivate+0x54/0x94
[ 814.404078][ T4558] Call trace:
[ 814.404080][ T4558] usb_gadget_deactivate+0x14/0xf4
[ 814.404083][ T4558] usb_function_deactivate+0x54/0x94
[ 814.404087][ T4558] uvc_function_disconnect+0x1c/0x5c
[ 814.404092][ T4558] uvc_v4l2_release+0x44/0xac
[ 814.404095][ T4558] v4l2_release+0xcc/0x130
Address the race condition and NULL pointer dereference by:
1. State Synchronization (flag + mutex)
Introduce a 'func_unbound' flag in struct uvc_device. This allows
uvc_function_disconnect() to safely skip accessing the nullified
cdev->gadget pointer. As suggested by Alan Stern, this flag is protected
by a new mutex (uvc->lock) to ensure proper memory ordering and prevent
instruction reordering or speculative loads. This mutex is also used to
protect 'func_connected' for consistent state management.
2. Explicit Synchronization (completion)
Use a completion to synchronize uvc_function_unbind() with the
uvc_vdev_release() callback. This prevents Use-After-Free (UAF) by
ensuring struct uvc_device is freed after all video device resources
are released.
Fixes: b81ac4395bbe ("usb: gadget: uvc: allow for application to cleanly shutdown")
Cc: stable <stable@kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Link: https://patch.msgid.link/20260320065427.1374555-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Another Silicon Motion flash drive also randomly work incorrectly
(lsusb does not list the device) on Huawei hisi platforms during
500 reboot cycles, and the DELAY_INIT quirk fixes this issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260319053927.264840-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
echi_brcm_wait_for_sof() gets called after disabling interrupts
in ehci_brcm_hub_control(). Use the atomic version of poll_timeout
to fix the warning.
Fixes: 9df231511bd6 ("usb: ehci: Add new EHCI driver for Broadcom STB SoC's")
Cc: stable <stable@kernel.org>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260318185707.2588431-1-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
partial transfer
When a gadget request is only partially transferred in transfer()
because the per-frame bandwidth budget is exhausted, the loop advances
to the next queued request. If that next request is a zero-length
packet (ZLP), len evaluates to zero and the code takes the
unlikely(len == 0) path, which sets is_short = 1. This bypasses the
bandwidth guard ("limit < ep->ep.maxpacket && limit < len") that
lives in the else branch and would otherwise break out of the loop for
non-zero requests. The is_short path then completes the URB before all
data from the first request has been transferred.
Reproducer (bulk IN, high speed):
Device side (FunctionFS with Linux AIO):
1. Queue a 65024-byte write via io_submit (127 * 512, i.e. a
multiple of the HS bulk max packet size).
2. Immediately queue a zero-length write (ZLP) via io_submit.
Host side:
3. Submit a 65536-byte bulk IN URB.
Expected: URB completes with actual_length = 65024.
Actual: URB completes with actual_length = 53248, losing 11776
bytes that leak into subsequent URBs.
At high speed the per-frame budget is 53248 bytes (512 * 13 * 8).
The 65024-byte request exhausts this budget after 53248 bytes, leaving
the request incomplete (req->req.actual < req->req.length). Neither
the request nor the URB is finished, and rescan is 0, so the loop
advances to the ZLP. For the ZLP, dev_len = 0, so len = min(12288, 0)
= 0, taking the unlikely(len == 0) path and setting is_short = 1.
The is_short handler then sets *status = 0, completing the URB with
only 53248 of the expected 65024 bytes.
Fix this by breaking out of the loop when the current request has
remaining data (req->req.actual < req->req.length). The request
resumes on the next timer tick, preserving correct data ordering.
Signed-off-by: Sebastian Urban <surban@surban.net>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260315151045.1155850-1-surban@surban.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When syscon_regmap_lookup_by_phandle_args() fails, the function was
returning directly without cleaning up the power domain initialized
earlier by dwc3_google_pm_domain_init().
Fix by jumping to err_deinit_pdom to properly clean up resources.
Fixes: 8995a37371bf4 ("usb: dwc3: Add Google Tensor SoC DWC3 glue driver")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260316-dwc3-google-v1-1-c9bde1b02f62@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This device has a union descriptor that is just garbage
and needs a custom descriptor.
In principle this could be done with a (conditionally
activated) heuristic. That would match more devices
without a need for defining a new quirk. However,
this always carries the risk that the heuristics
does the wrong thing and leads to more breakage.
Defining the quirk and telling it exactly what to do
is the safe and conservative approach.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260317084139.1461008-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit 4fb352df14de ("PM: sleep: Do not flag runtime PM workqueue
as freezable"), pm_wq workqueue will be unfreezable during system pm. This
brings issue as below:
[ 344.255749] ------------[ cut here ]------------
[ 344.277740] URB 000000004aae4ad1 submitted while active
[ 344.282996] WARNING: drivers/usb/core/urb.c:379 at usb_submit_urb+0x5a4/0x5e0, CPU#2: kworker/u16:14/964
[ 344.292477] Modules linked in:
[ 344.295532] CPU: 2 UID: 0 PID: 964 Comm: kworker/u16:14 Not tainted 7.0.0-rc2-next-20260303-00006-gf03fe0b53b39-dirty #100 PREEMPT
[ 344.307341] Hardware name: NXP i.MX943 EVK board (DT)
[ 344.312386] Workqueue: async async_run_entry_fn
[ 344.316919] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 344.323862] pc : usb_submit_urb+0x5a4/0x5e0
[ 344.328046] lr : usb_submit_urb+0x5a4/0x5e0
[ 344.332217] sp : ffff800083283b30
[ 344.335528] x29: ffff800083283b30 x28: ffff000082631000 x27: 0000000000000000
[ 344.342661] x26: 0000000000000003 x25: 0000000000000c00 x24: 0000000000000000
[ 344.349793] x23: 0000000000000004 x22: 0000000000000010 x21: 0000000000000000
[ 344.356917] x20: 0000000000000002 x19: ffff00008253ce40 x18: ffff000089e4eec0
[ 344.364050] x17: 000000040044ffff x16: 000005d9d87f6289 x15: 0000000000000000
[ 344.371174] x14: ffff000089e4eec0 x13: 6576697463612065 x12: 6c69687720646574
[ 344.378298] x11: 0000000000000058 x10: 0000000000000001 x9 : 0000000000000001
[ 344.385431] x8 : 0000000000000000 x7 : 0000005028dd0800 x6 : 0000000000000002
[ 344.392563] x5 : ffffc48f74e9daf8 x4 : 0000000000000000 x3 : 0000000000000000
[ 344.399696] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000089e4ee40
[ 344.406835] Call trace:
[ 344.409280] usb_submit_urb+0x5a4/0x5e0 (P)
[ 344.413456] hub_activate+0x268/0x878
[ 344.417116] hub_resume+0x5c/0x10c
[ 344.420522] usb_resume_interface.isra.0+0xa8/0x110
[ 344.425393] usb_resume_both+0x10c/0x1e0
[ 344.429310] usb_resume+0x1c/0x70
[ 344.432621] usb_dev_resume+0x14/0x20
[ 344.436278] dpm_run_callback.isra.0+0x38/0xf8
[ 344.440715] device_resume+0xec/0x1e8
[ 344.444373] async_resume+0x20/0x38
[ 344.447848] async_run_entry_fn+0x34/0xe0
[ 344.451852] process_one_work+0x150/0x290
[ 344.455856] worker_thread+0x18c/0x300
[ 344.459600] kthread+0x118/0x124
[ 344.462824] ret_from_fork+0x10/0x20
The reason is if the host controller resume routine xhci_resume() call
usb_hcd_resume_root_hub(), wakeup_work will be queued and run immediately.
Then usb_autoresume_device() will be called and usb device will exit
runtime suspended state (if it was suspended before). For a hub device,
hub_resume()/hub_reset_resume() will be called accordingly.
After the host controller device system resume is finished, the root hub
usb device "usb1" will do system resume too. Then hub_resume() will be
called again.
Above sequence will cause hub->urb to be submitted twice. To avoid this
issue, restore the previous behavior by queuing wakeup_work to
system_freezable_wq workqueue.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 4fb352df14de ("PM: sleep: Do not flag runtime PM workqueue as freezable")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260316094811.1559471-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ec35c1969650 ("usb: gadget: f_ncm: Fix net_device lifecycle with
device_move") reparents the gadget device to /sys/devices/virtual during
unbind, clearing the gadget pointer. If the userspace tool queries on
the surviving interface during this detached window, this leads to a
NULL pointer dereference.
Unable to handle kernel NULL pointer dereference
Call trace:
eth_get_drvinfo+0x50/0x90
ethtool_get_drvinfo+0x5c/0x1f0
__dev_ethtool+0xaec/0x1fe0
dev_ethtool+0x134/0x2e0
dev_ioctl+0x338/0x560
Add a NULL check for dev->gadget in eth_get_drvinfo(). When detached,
skip copying the fw_version and bus_info strings, which is natively
handled by ethtool_get_drvinfo for empty strings.
Suggested-by: Val Packett <val@packett.cool>
Reported-by: Val Packett <val@packett.cool>
Closes: https://lore.kernel.org/linux-usb/10890524-cf83-4a71-b879-93e2b2cc1fcc@packett.cool/
Fixes: ec35c1969650 ("usb: gadget: f_ncm: Fix net_device lifecycle with device_move")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260316-eth-null-deref-v1-1-07005f33be85@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes an error in synchronization in the dummy-hcd driver. The
error has a somewhat involved history. The synchronization mechanism
was introduced by commit 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous
synchronization change"), which added an emulated "interrupts enabled"
flag together with code emulating synchronize_irq() (it waits until
all current handler callbacks have returned).
But the emulated interrupt-disable occurred too late, after the driver
containing the handler callback routines had been told that it was
unbound and no more callbacks would occur. Commit 4a5d797a9f9c ("usb:
gadget: dummy_hcd: fix gpf in gadget_setup") tried to fix this by
moving the synchronize_irq() emulation code from dummy_stop() to
dummy_pullup(), which runs before the unbind callback.
There still were races, though, because the emulated interrupt-disable
still occurred too late. It couldn't be moved to dummy_pullup(),
because that routine can be called for reasons other than an impending
unbind. Therefore commits 7dc0c55e9f30 ("USB: UDC core: Add
udc_async_callbacks gadget op") and 04145a03db9d ("USB: UDC: Implement
udc_async_callbacks in dummy-hcd") added an API allowing the UDC core
to tell dummy-hcd exactly when emulated interrupts and their callbacks
should be disabled.
That brings us to the current state of things, which is still wrong
because the emulated synchronize_irq() occurs before the emulated
interrupt-disable! That's no good, beause it means that more emulated
interrupts can occur after the synchronize_irq() emulation has run,
leading to the possibility that a callback handler may be running when
the gadget driver is unbound.
To fix this, we have to move the synchronize_irq() emulation code yet
again, to the dummy_udc_async_callbacks() routine, which takes care of
enabling and disabling emulated interrupt requests. The
synchronization will now run immediately after emulated interrupts are
disabled, which is where it belongs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 04145a03db9d ("USB: UDC: Implement udc_async_callbacks in dummy-hcd")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/c7bc93fe-4241-4d04-bd56-27c12ba35c97@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Syzbot testing was able to provoke an addressing exception and crash
in the usb_gadget_udc_reset() routine in
drivers/usb/gadgets/udc/core.c, resulting from the fact that the
routine was called with a second ("driver") argument of NULL. The bad
caller was set_link_state() in dummy_hcd.c, and the problem arose
because of a race between a USB reset and driver unbind.
These sorts of races were not supposed to be possible; commit
7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change"),
along with a few followup commits, was written specifically to prevent
them. As it turns out, there are (at least) two errors remaining in
the code. Another patch will address the second error; this one is
concerned with the first.
The error responsible for the syzbot crash occurred because the
stop_activity() routine will sometimes drop and then re-acquire the
dum->lock spinlock. A call to stop_activity() occurs in
set_link_state() when handling an emulated USB reset, after the test
of dum->ints_enabled and before the increment of dum->callback_usage.
This allowed another thread (doing a driver unbind) to sneak in and
grab the spinlock, and then clear dum->ints_enabled and dum->driver.
Normally this other thread would have to wait for dum->callback_usage
to go down to 0 before it would clear dum->driver, but in this case it
didn't have to wait since dum->callback_usage had not yet been
incremented.
The fix is to increment dum->callback_usage _before_ calling
stop_activity() instead of after. Then the thread doing the unbind
will not clear dum->driver until after the call to
usb_gadget_udc_reset() safely returns and dum->callback_usage has been
decremented again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19bed92c97bee999e5db@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/68fc7c9c.050a0220.346f24.023c.GAE@google.com/
Tested-by: syzbot+19bed92c97bee999e5db@syzkaller.appspotmail.com
Fixes: 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/46135f42-fdbe-46b5-aac0-6ca70492af15@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The connector number extracted from CCI via UCSI_CCI_CONNECTOR() is a
7-bit field (0-127) that is used to index into the connector array in
ucsi_connector_change(). However, the array is only allocated for the
number of connectors reported by the device (typically 2-4 entries).
A malicious or malfunctioning device could report an out-of-range
connector number in the CCI, causing an out-of-bounds array access in
ucsi_connector_change().
Add a bounds check in ucsi_notify_common(), the central point where CCI
is parsed after arriving from hardware, so that bogus connector numbers
are rejected before they propagate further.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Nathan Rebello <nathan.c.rebello@gmail.com>
Link: https://patch.msgid.link/20260313222453.123-1-nathan.c.rebello@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When calling usbtmc_release, pending anchored URBs must be flushed or
killed to prevent use-after-free errors (e.g. in the HCD giveback
path). Call usbtmc_draw_down() to allow anchored URBs to be completed.
Fixes: 4f3c8d6eddc2 ("usb: usbtmc: Support Read Status Byte with SRQ per file")
Reported-by: syzbot+9a3c54f52bd1edbd975f@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9a3c54f52bd1edbd975f
Cc: stable <stable@kernel.org>
Signed-off-by: Heitor Alves de Siqueira <halves@igalia.com>
Link: https://patch.msgid.link/20260312-usbtmc-flush-release-v1-1-5755e9f4336f@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A race condition between gether_disconnect() and eth_stop() leads to a
NULL pointer dereference. Specifically, if eth_stop() is triggered
concurrently while gether_disconnect() is tearing down the endpoints,
eth_stop() attempts to access the cleared endpoint descriptor, causing
the following NPE:
Unable to handle kernel NULL pointer dereference
Call trace:
__dwc3_gadget_ep_enable+0x60/0x788
dwc3_gadget_ep_enable+0x70/0xe4
usb_ep_enable+0x60/0x15c
eth_stop+0xb8/0x108
Because eth_stop() crashes while holding the dev->lock, the thread
running gether_disconnect() fails to acquire the same lock and spins
forever, resulting in a hardlockup:
Core - Debugging Information for Hardlockup core(7)
Call trace:
queued_spin_lock_slowpath+0x94/0x488
_raw_spin_lock+0x64/0x6c
gether_disconnect+0x19c/0x1e8
ncm_set_alt+0x68/0x1a0
composite_setup+0x6a0/0xc50
The root cause is that the clearing of dev->port_usb in
gether_disconnect() is delayed until the end of the function.
Move the clearing of dev->port_usb to the very beginning of
gether_disconnect() while holding dev->lock. This cuts off the link
immediately, ensuring eth_stop() will see dev->port_usb as NULL and
safely bail out.
Fixes: 2b3d942c4878 ("usb ethernet gadget: split out network core")
Cc: stable <stable@kernel.org>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://patch.msgid.link/20260311-gether-disconnect-npe-v1-1-454966adf7c7@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Blackbox 724-746-5500 USB Director USB-RS-232 HUB, part number
IC135A, is a rebadged Edgeport/4 with its own USB device id.
Signed-off-by: Frej Drejhammar <frej@stacken.kth.se>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add VID/PID 33f8:1003 for the Rolling Wireless RW135R-GL M.2 module,
which is used in laptop debug cards with MBIM interface for
Linux/Chrome OS. The device supports mbim, pipe functionalities.
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=1003 Rev=05.15
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling RW135R-GL Module
S: SerialNumber=12345678
C: #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Signed-off-by: Wanquan Zhong <wanquan.zhong@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add USB_QUIRK_NO_BOS for ezcap401 capture card, without it dmesg will show
"unable to get BOS descriptor or descriptor too short" and "unable to
read config index 0 descriptor/start: -71" errors and device will not
able to work at full speed at 10gbs
Signed-off-by: Vyacheslav Vahnenko <vahnenko2003@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260313123638.20481-1-vahnenko2003@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
