| Age | Commit message (Collapse) | Author |
|---|
|
[WHY & HOW]
IPS & self-fresh feature can cause vblank counter resets between
vblank disable and enable.
It may cause system stuck due to wait the vblank counter.
Call the drm_crtc_vblank_restore() during vblank enable to estimate
missed vblanks by using timestamps and update the vblank counter in
DRM.
It can make the vblank counter increase smoothly and resolve this issue.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 34d66bc7ff10e146a4cec76cf286979740a10954)
Cc: stable@vger.kernel.org
|
|
amdgpu_dm_commit_planes calls update_freesync_state_on_stream only for
the primary plane. If a commit affects a CRTC but not its primary plane,
it would previously not trigger a refresh cycle or affect LFC, violating
current UAPI semantics.
Fixes e.g. atomic commits affecting only the cursor plane being limited
to the minimum refresh rate.
Don't do this for the legacy cursor ioctls though, it would break the
UAPI semantics for those.
Suggested-by: Xaver Hugl <xaver.hugl@kde.org>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3034
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit cc7bfba95966251b254cb970c21627124da3b7f4)
Cc: stable@vger.kernel.org
|
|
In DCN401 pre-blending degamma LUT isn't affecting cursor as in previous
DCN version. As this is not the behavior close to what is expected for
CRTC degamma LUT, disable CRTC degamma LUT property in this HW.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/4176
---
When enabling HDR on KDE, it takes the first CRTC 1D LUT available and
apply a color transformation (Gamma 2.2 -> PQ). AMD driver usually
advertises a CRTC degamma LUT as the first CRTC 1D LUT, but it's
actually applied pre-blending. In previous HW version, it seems to work
fine because the 1D LUT was applied to cursor too, but DCN401 presents a
different behavior and the 1D LUT isn't affecting the hardware cursor.
To address the wrong gamma on cursor with HDR (see the link), I came up
with this patch that disables CRTC degamma LUT in this hw, since it
presents a different behavior than others. With this KDE sees CRTC
regamma LUT as the first post-blending 1D LUT available. This is
actually more consistent with AMD color pipeline. It was tested by the
reporter, since I don't have the HW available for local testing and
debugging.
Melissa
---
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 50f29ead1f1ba48983b6c5e3813b15e497714f55.
Reason for revert: cause corruption on Dell U3224KB DP2 display.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pause the workload setting in dm when doing idle optimization
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b23f81c442ac33af0c808b4bb26333b881669bb7)
|
|
amdgpu_dm_commit_planes()
[Why]
Replay and PSR will cause some video corruption while VRR is enabled.
[How]
Do not enable the Replay and PSR while VRR is active in
amdgpu_dm_enable_self_refresh().
Fixes: 67edb81d6e9a ("drm/amd/display: Disable replay and psr while VRR is enabled")
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Replay and PSR will cause some video corruption while VRR is enabled.
[How]
1. Disable the Replay and PSR while VRR is enabled.
2. Change the amdgpu_dm_crtc_vrr_active() parameter to const.
Because the function will only read data from dm_crtc_state.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d7879340e987b3056b8ae39db255b6c19c170a0d)
Cc: stable@vger.kernel.org
|
|
[Why]
Outside of a modeset/link configuration change, we should not have to
wait for the panel to exit PSR. Depending on the panel and it's state,
it may take multiple frames for it to exit PSR. Therefore, waiting in
all scenarios may cause perceived stuttering, especially in combination
with faster vblank shutdown.
[How]
PSR1 disable is hooked up to the vblank enable event, and vice versa. In
case of vblank enable, do not wait for panel to exit PSR, but still wait
in all other cases.
We also avoid a call to unnecessarily change power_opts on disable -
this ends up sending another command to dmcub fw.
When testing against IGT, some crc tests like kms_plane_alpha_blend and
amd_hotplug were failing due to CRC timeouts. This was found to be
caused by the early return before HW has fully exited PSR1. Fix this by
first making sure we grab a vblank reference, then waiting for panel to
exit PSR1, before programming hw for CRC generation.
Fixes: 58a261bfc967 ("drm/amd/display: use a more lax vblank enable policy for older ASICs")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3743
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit aa6713fa2046f4c09bf3013dd1420ae15603ca6f)
Cc: stable@vger.kernel.org
|
|
[Why]
In certain use case such as KDE login screen, there will be no atomic
commit while do the frame update.
If the Panel Replay enabled, it will cause the screen not updated and
looks like system hang.
[How]
Delay few atomic commits before enabled the Panel Replay just like PSR.
Fixes: be64336307a6c ("drm/amd/display: Re-enable panel replay feature")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3686
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3682
Tested-By: Corey Hickey <bugfood-c@fatooh.org>
Tested-By: James Courtier-Dutton <james.dutton@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Panel Replay feature may also use the same variable with PSR.
Change the variable name and make it not specify for PSR.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Whether we really enter idle optimizations are decided within DC.
Printing into dmesg before calling the DC API gives an incorrect
indication that we are entering idle optimization in cases where its
disabled manually.
To fix this, remove the print in DM and add them in DC
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix DP Compliance test 4.2.1.3, 4.2.2.8, 4.3.1.12, 4.3.1.13
when IPS enabled.
Original HPD detection interval is set to 5s which violates DP
compliance.
Reduce the interval parameter, such that link training can be
finished within 5 seconds.
Fixes: afca033f10d3 ("drm/amd/display: Add periodic detection for IPS")
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Idle worker thread waits HPD_DETECTION_TIME for HPD processing complete.
Some displays require longer time for that.
[How]
Increase HPD_DETECTION_TIME to 100ms.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Idle worker thread serves for periodic detection of HPD while system is in IPS2.
Currently it is used in headless and static screen scenarios.
IPX can be configured not to execute IPS2 for static screen.
In this case idle worker is redundant.
[How]
Only use periodic detection for static screen if IPS is fully enabled.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
1. After allowing idle optimizations, hw programming is disallowed.
2. Before hw programming, we need to disallow idle optimizations.
Otherwise, in scenario 1, we will immediately kick hw out of idle
optimizations with register access.
Scenario 2 is less of a concern, since any register access will kick
hw out of idle optimizations. But we'll do it early for correctness.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We manage interrupts for CRTCs in two places:
1. In manage_dm_interrupts(), when CRTC get enabled or disabled
2. When drm_vblank_get/put() starts or kills the vblank counter, calling
into amdgpu_dm_crtc_set_vblank()
The interrupts managed by these twp places should be identical.
[How]
Since manage_dm_interrupts() already use drm_crtc_vblank_on/off(), just
move all CRTC interrupt management into amdgpu_dm_crtc_set_vblank().
This has the added benefit of disabling all CRTC and HUBP interrupts
when there are no vblank requestors.
Note that there is a TODO item - unchanged from when it was first
introduced - to properly identify the HUBP instance from the OTG
instance, rather than just assume direct mapping.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Hotplug is not detected in headless (no eDP) mode on dcn35x.
With no display dcn35x goes to IPS2 powersaving state where HPD interrupt
is not handled.
[HOW]
Use idle worker thread for periodic detection of HPD in headless mode.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN is the display hardware for amdgpu. DRM planes are backed by DCN
hardware pipes, which carry pixel data from one end (memory), to the
other (output encoder).
Each DCN pipe has the ability to blend in a cursor early on in the
pipeline. In other words, there are no dedicated cursor planes in DCN,
which makes cursor behavior somewhat unintuitive for compositors.
For example, if the cursor is in RGB format, but the top-most DRM plane
is in YUV format, DCN will not be able to blend them. Because of this,
amdgpu_dm rejects all configurations where a cursor needs to be enabled
on top of a YUV formatted plane.
From a compositor's perspective, when computing an allocation for
hardware plane offloading, this cursor-on-yuv configuration result in an
atomic test failure. Since the failure reason is not obvious at all,
compositors will likely fall back to full rendering, which is not ideal.
Instead, amdgpu_dm can try to accommodate the cursor-on-yuv
configuration by opportunistically reserving a separate DCN pipe just
for the cursor. We can refer to this as "overlay cursor mode". It is
contrasted with "native cursor mode", where the native DCN per-pipe
cursor is used.
[How]
On each crtc, compute whether the cursor plane should be enabled in
overlay mode. If it is, mark the CRTC as requesting overlay cursor mode.
Overlay cursor should be enabled whenever there exists a underlying
plane that has YUV format, or is scaled differently than the cursor. It
should also be enabled if there is no underlying plane, or if underlying
planes do not cover the entire CRTC.
During DC validation, attempt to enable a separate DCN pipe for the
cursor if it's in overlay mode. If that fails, or if no overlay mode is
requested, then fallback to native mode.
v2:
* Update commit message for when overlay cursor should be enabled
* Also consider scale and no-underlying-plane case (cursor on crtc bg)
* Consider all underlying planes when determinig overlay/native, not
just the plane immediately beneath the cursor, as it may not cover the
entire CRTC.
* Fix typo s/decending/descending/
* Force native cursor on pre-DCN hardware
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
HPD interrupt cannot be handled in IPS2 state.
So if there's a display topology change while system in IPS2
it can be missed.
[How]
Implement worker to check each 5 sec in IPS for HPD.
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
fix reading edp rx crc timeout failure. after
bootup, kernel setup psr with dpcd 0x170 = 5. this
notify rx psr enable and let rx fw start checking crc
for fw internal logic. rx fw may not update crc read
count within dpcd 0x246. read count is always 0. this
will lead tx crc reading timeout.
[How]
add debugfs to let test app to disbable rx crc
checking for rx internal logic. then test app can read
rx crc dpcd 0x246 successfully.
expected app sequence is as below:
1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2.
2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr
3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but
without dpcd 0x170 = 5.
4. read crc from rx dpcd 0x270, 0x246, etc.
5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr.
this will let eDP back to normal with psr setup dpcd 0x170 = 5.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'amdgpu_dm_crtc_set_panel_sr_feature()'
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_crtc.c:100: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* The DRM vblank counter enable/disable action is used as the trigger
to enable
Cc: Sun peng Li <sunpeng.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Enable the Panel Replay if eDP panel and ASIC support.
(prioritize Panel Replay over PSR)
[How]
- Setup the Panel Replay config during the device init
(prioritize Panel Replay over PSR).
- Separate the Replay init function into two functions
amdgpu_dm_link_setup_replay() and amdgpu_dm_set_replay_caps()
to fix the issue in the earlier commit that cause PSR and Replay
enabled at the same time.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Use tabs, not spaces.
- Brace and parentheses placement
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 44e60b14d5a72f91fd0bdeae8da59ae37a3ca8e5.
Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.
This got brought back accidently with the backmerge.
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
warning: expecting prototype for drm_crtc_additional_color_mgmt().
Prototype was for dm_crtc_additional_color_mgmt() instead
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312141801.o9eBCxt9-lkp@intel.com/
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add AMD pre-defined transfer function property to default DRM CRTC gamma
to convert to wire encoding with or without a user gamma LUT. There is
no post-blending regamma ROM for pre-defined TF. When setting Gamma TF
(!= Identity) and LUT at the same time, the color module will combine
the pre-defined TF and the custom LUT values into the LUT that's
actually programmed.
v2:
- enable CRTC prop in the end of driver-specific prop sequence
- define inverse EOTFs as supported regamma TFs
- reword driver-specific function doc to remove shaper/3D LUT
v3:
- spell out TF+LUT behavior in the commit and comments (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The ftrace debug feature allows filtering functions based on a prefix,
which can be helpful in some complex debug scenarios. The driver can
benefit more from this feature if the function name follows some
patterns; for this reason, this commit adds the prefix amdgpu_dm_crtc_
to all the functions that do not have it in the amdgpu_dm_crtc.c file.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.
The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.
Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.
This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
