| Age | Commit message (Collapse) | Author |
|---|
|
Add tests where one link has different rates of packet loss or reorders
packets. PRP should still be able to recover from these link faults and
show no packet loss. However, it is acceptable to receive some level of
duplicate packets. This matches the current specification (IEC
62439-3:2021) of the duplicate discard algorithm that requires it to be
"designed such that it never rejects a legitimate frame, while occasional
acceptance of a duplicate can be tolerated." The rate of acceptable
duplicates in this test is intentionally high (10%) to make the test
stable, the values I observed in the worst test cases (20% loss) are around
5% duplicates.
The duplicates occur because of the 10ms ping interval in the test. As
blocks expire after 400ms based on the timestamp of the first received
sequence number in the block, every approx. 40th will lead to a new, clean
block being used where the sequence number hasn't been seen before. As this
occurs on both nodes in the test (for requests and replies), we observe
around 20 duplicate frames.
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/7b36506d3a80e53786fe56526cf6046c74dfeee1.1770299429.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a test case that can support different types of faulty links for all
protocol versions (HSRv0, HSRv1, PRPv1). It starts with a baseline with
fully functional links. The first faulty case is one link being cut during
the ping. This test uses a different function for ping that sends more
packets in shorter intervals to stress the duplicate detection algorithms a
bit more and allow for future tests with other link faults (packet loss,
reordering, etc.).
As the link fault tests now cover the cut link for HSR and PRP, it can be
removed from the hsr_ping test. Note that the removed cut link test did not
really test the fault because do_ping_long takes about 1sec while the link
is only cut after a 3sec sleep.
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/dad52276e2c349ecb96168bef7e3001bf7becc81.1770299429.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previously the hsr_ping test only checked that all nodes in a VLAN are
reachable (using do_ping). Update the test to also check that there is no
packet loss and no duplicate packets by running the same tests for VLANs as
without VLANs (including using do_ping_long). This also adds tests for IPv6
over VLAN. To unify the test code, the topology without VLANs now uses IP
addresses from dead:beef:0::/64 to align with the 100.64.0.0/24 range for
IPv4. Error messages are updated across the board to make it easier to find
what actually failed.
Also update the VLAN test to only run in VLAN 2, as there is no need to
check if ping really works with VLAN IDs 2, 3, 4, and 5. This lowers the
number of long ping tests on VLANs to keep the overall test runtime in
bounds.
It's still necessary to bump the test timeout a bit, though: a ping long
tests takes 1sec, do_ping_tests performs 12 of them, do_link_problem_tests
6, and the VLAN tests again 12. With some buffer for setup and waiting and
for two protocol versions, 90sec timeout seems reasonable.
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/e3ded0e2547b5f720524b62fabeb96debc579697.1770299429.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a selftest for PRP that performs a basic ping test on IPv4 and IPv6,
over the plain PRP interface and a VLAN interface, similar to the existing
ping test for HSR. The test first checks reachability of the other node,
then checks for no loss and no duplicates.
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/4a342189e842d7308d037da72af566729ee75834.1770299429.git.fmaurer@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
`objtool` with Rust 1.84.0 reports:
rust/kernel.o: error: objtool: _RNvXNtNtCsaRPFapPOzLs_6kernel3str9parse_intaNtNtB2_7private12FromStrRadix14from_str_radix()
falls through to next function _RNvXNtNtCsaRPFapPOzLs_6kernel3str9parse_intaNtNtB2_7private12FromStrRadix16from_u64_negated()
This is very similar to commit c18f35e49049 ("objtool/rust: add one more
`noreturn` Rust function"), which added `from_ascii_radix_panic` for Rust
1.86.0, except that Rust 1.84.0 ends up needing `from_str_radix_panic`.
Thus add it to the list to fix the warning.
Cc: FUJITA Tomonori <fujita.tomonori@gmail.com>
Fixes: 51d9ee90ea90 ("rust: str: add radix prefixed integer parsing functions")
Reported-by: Alice Ryhl <aliceryhl@google.com>
Link: https://rust-for-linux.zulipchat.com/#narrow/channel/291565/topic/x/with/572427627
Tested-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20260206204336.38462-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Extend ynltool to compute HW GRO savings metric - how many
packets has HW GRO been able to save the kernel from seeing.
Note that this definition does not actually take into account
whether the segments were or weren't eligible for HW GRO.
If a machine is receiving all-UDP traffic - new metric will show
HW-GRO savings of 0%. Conversely since the super-packet still
counts as a received packet, savings of 100% is not achievable.
Perfect HW-GRO on a machine with 4k MTU and 64kB super-frames
would show ~93.75% savings. With 1.5k MTU we may see up to
~97.8% savings (if my math is right).
Example after 10 sec of iperf on a freshly booted machine
with 1.5k MTU:
$ ynltool qstats show
eth0 rx-packets: 40681280 rx-bytes: 61575208437
rx-alloc-fail: 0 rx-hw-gro-packets: 1225133
rx-hw-gro-wire-packets: 40656633
$ ynltool qstats hw-gro
eth0: 96.9% savings
None of the NICs I have access to can report "missed" HW-GRO
opportunities so computing a true "effectiveness" metric
is not possible. One could also argue that effectiveness metric
is inferior in environments where we control both senders and
receivers, the savings metrics will capture both regressions
in receiver's HW GRO effectiveness but also regressions in senders
sending smaller TSO trains. And we care about both. The main
downside is that it's hard to tell at a glance how well the NIC
is doing because the savings will be dependent on traffic patterns.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260207003509.3927744-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The logic to open a socket and dump the queues is the same
across sub-commands. Factor it out, we'll need it again.
No functional changes intended.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20260207003509.3927744-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull documentation updates from Jonathan Corbet:
"A slightly calmer cycle for docs this time around, though there is
still a fair amount going on, including:
- Some signs of life on the long-moribund Japanese translation
- Documentation on policies around the use of generative tools for
patch submissions, and a separate document intended for consumption
by generative tools
- The completion of the move of the documentation tools to
tools/docs. For now we're leaving a /scripts/kernel-doc symlink
behind to avoid breaking scripts
- Ongoing build-system work includes the incorporation of
documentation in Python code, better support for documenting
variables, and lots of improvements and fixes
- Automatic linking of man-page references -- cat(1), for example --
to the online pages in the HTML build
...and the usual array of typo fixes and such"
* tag 'docs-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/docs/linux: (107 commits)
doc: development-process: add notice on testing
tools: sphinx-build-wrapper: improve its help message
docs: sphinx-build-wrapper: allow -v override -q
docs: kdoc: Fix pdfdocs build for tools
docs: ja_JP: process: translate 'Obtain a current source tree'
docs: fix 're-use' -> 'reuse' in documentation
docs: ioctl-number: fix a typo in ioctl-number.rst
docs: filesystems: ensure proc pid substitutable is complete
docs: automarkup.py: Skip common English words as C identifiers
Documentation: use a source-read extension for the index link boilerplate
docs: parse_features: make documentation more consistent
docs: add parse_features module documentation
docs: jobserver: do some documentation improvements
docs: add jobserver module documentation
docs: kabi: helpers: add documentation for each "enum" value
docs: kabi: helpers: add helper for debug bits 7 and 8
docs: kabi: system_symbols: end docstring phrases with a dot
docs: python: abi_regex: do some improvements at documentation
docs: python: abi_parser: do some improvements at documentation
docs: add kabi modules documentation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"There's a little less than normal, probably due to LPC & Christmas/New
Year meaning that a few series weren't quite ready or reviewed in
time. It's still useful across the board, despite the only real
feature being support for the LS64 feature enabling 64-byte atomic
accesses to endpoints that support it.
ACPI:
- Add interrupt signalling support to the AGDI handler
- Add Catalin and myself to the arm64 ACPI MAINTAINERS entry
CPU features:
- Drop Kconfig options for PAN and LSE (these are detected at runtime)
- Add support for 64-byte single-copy atomic instructions (LS64/LS64V)
- Reduce MTE overhead when executing in the kernel on Ampere CPUs
- Ensure POR_EL0 value exposed via ptrace is up-to-date
- Fix error handling on GCS allocation failure
CPU frequency:
- Add CPU hotplug support to the FIE setup in the AMU driver
Entry code:
- Minor optimisations and cleanups to the syscall entry path
- Preparatory rework for moving to the generic syscall entry code
Hardware errata:
- Work around Spectre-BHB on TSV110 processors
- Work around broken CMO propagation on some systems with the SI-L1
interconnect
Miscellaneous:
- Disable branch profiling for arch/arm64/ to avoid issues with
noinstr
- Minor fixes and cleanups (kexec + ubsan, WARN_ONCE() instead of
WARN_ON(), reduction of boolean expression)
- Fix custom __READ_ONCE() implementation for LTO builds when
operating on non-atomic types
Perf and PMUs:
- Support for CMN-600AE
- Be stricter about supported hardware in the CMN driver
- Support for DSU-110 and DSU-120
- Support for the cycles event in the DSU driver (alongside the
dedicated cycles counter)
- Use IRQF_NO_THREAD instead of IRQF_ONESHOT in the cxlpmu driver
- Use !bitmap_empty() as a faster alternative to bitmap_weight()
- Fix SPE error handling when failing to resume profiling
Selftests:
- Add support for the FORCE_TARGETS option to the arm64 kselftests
- Avoid nolibc-specific my_syscall() function
- Add basic test for the LS64 HWCAP
- Extend fp-pidbench to cover additional workload patterns"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (43 commits)
perf/arm-cmn: Reject unsupported hardware configurations
perf: arm_spe: Properly set hw.state on failures
arm64/gcs: Fix error handling in arch_set_shadow_stack_status()
arm64: Fix non-atomic __READ_ONCE() with CONFIG_LTO=y
arm64: poe: fix stale POR_EL0 values for ptrace
kselftest/arm64: Raise default number of loops in fp-pidbench
kselftest/arm64: Add a no-SVE loop after SVE in fp-pidbench
perf/cxlpmu: Replace IRQF_ONESHOT with IRQF_NO_THREAD
arm64: mte: Set TCMA1 whenever MTE is present in the kernel
arm64/ptrace: Return early for ptrace_report_syscall_entry() error
arm64/ptrace: Split report_syscall()
arm64: Remove unused _TIF_WORK_MASK
kselftest/arm64: Add missing file in .gitignore
arm64: errata: Workaround for SI L1 downstream coherency issue
kselftest/arm64: Add HWCAP test for FEAT_LS64
arm64: Add support for FEAT_{LS64, LS64_V}
KVM: arm64: Enable FEAT_{LS64, LS64_V} in the supported guest
arm64: Provide basic EL2 setup for FEAT_{LS64, LS64_V} usage at EL0/1
KVM: arm64: Handle DABT caused by LS64* instructions on unsupported memory
KVM: arm64: Add documentation for KVM_EXIT_ARM_LDST64B
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nolibc/linux-nolibc
Pull nolibc updates from Thomas Weißschuh:
- All time-related functionality uses 64-bit timestamps for
y2038 compatibility
- fread() and fskeek() support
- ptrace() support
- Addition of libc-test to the regular kselftests
- Smaller cleanups and fixes to the code and build system
* tag 'nolibc-20260206-for-7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/nolibc/linux-nolibc: (25 commits)
tools/nolibc: Add a simple test for writing to a FILE and reading it back
tools/nolibc: Add fseek() to stdio.h
tools/nolibc: Add fread() to stdio.h
selftests/nolibc: also test libc-test through regular selftest framework
selftests/nolibc: scope custom flags to the nolibc-test target
selftests/nolibc: try to read from stdin in readv_zero test
selftests/nolibc: always build sparc32 tests with -mcpu=v8
tools/nolibc: align sys_vfork() with sys_fork()
selftests/nolibc: drop NOLIBC_SYSROOT=0 logic
selftests/nolibc: add static assertions around time types handling
tools/nolibc: add __nolibc_static_assert()
tools/nolibc: add compiler version detection macros
tools/nolibc: remove time conversions
selftests/nolibc: test compatibility of nolibc and kernel time types
tools/nolibc: always use 64-bit time types
tools/nolibc: use custom structs timespec and timeval
tools/nolibc/select: avoid libgcc 64-bit multiplications
tools/nolibc/gettimeofday: avoid libgcc 64-bit divisions
tools/nolibc: prefer explicit 64-bit time-related system calls
tools/nolibc/time: drop invocation of gettimeofday system call
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These add support for "slow" (long-term trend) workload type hints to
the Intel int340x thermal driver and selftests (and enable it for
Panther Lake), add support for MT8196 along with DT bindings and for
MT7987 to the Mediatek LVTS thermal driver, add support for RZ/T2H and
RZ/N2H along with DT bindings to the Renesas rzg3e thermal driver, add
support for the Panther Lake, Wildcat Lake and Nova Lake processors to
the intel_tcc_cooling driver, fix bugs, make some cosmetic changes
including code cleanups and library function substitutions, and update
documentation.
Specifics:
- Add Panther Lake, Wildcat Lake and Nova Lake processor IDs to the
list of supported processors in the intel_tcc_cooling thermal
driver (Srinivas Pandruvada)
- Drop unnecessary explicit driver data clearing on removal from the
intel_pch_thermal driver (Kaushlendra Kumar)
- Add support for "slow" workload type hints to the int340x
processor_thermal driver and enable it on the Panther Lake platform
(Srinivas Pandruvada)
- Use sysfs_emit{_at}() in sysfs show functions in Intel thermal
drivers (Thorsten Blum)
- Update the x86_pkg_temp_thermal driver to handle
THERMAL_TEMP_INVALID that can be passed to it via sysfs as expected
(Rafael Wysocki)
- Drop a redundant local variable from the intel_tcc_cooling thermal
driver and fix a kerneldoc comment typo in the TCC library (Sumeet
Pawnikar)
- Fix CFLAGS and LDFLAGS in the pkg-config libthermal template
(Romain Gantois)
- Support multiple temp to raw conversion functions in the Mediatek
LVTS thermal driver and add MT8196 and MT6991 support to it (Laura
Nao)
- Add Mediatek LVTS driver support for MT7987 (Frank Wunderlich)
- Use the existing HZ_PER_MHZ macro on STM32 (Andy Shevchenko)
- Use the existing clamp() macro on BCM2835 (Thorsten Blum)
- Make the reset line optional in order to support new Renesas SoCs
where it is not available and add support for RZ/T2H and RZ/N2H to
the rzg3e thermal driver (Cosmin Tanislav)
- Document RZ/V2N TSU in the r9a09g047-tsu DT bindings (Ovidiu
Panait)
- Fix all kernel-doc warnings in the internal thermal core header
file (Randy Dunlap)
- Fix a device node reference leak in thermal_of_cm_lookup() (Felix
Gu)
- Replace some old-style library function calls with ones that are
currently recommended in several places in the thermal core and
debugfs code (Sumeet Pawnikar, Thorsten Blum)
* tag 'thermal-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
drivers: thermal: intel: tcc_cooling: Drop redundant local variable
thermal/of: Fix reference leak in thermal_of_cm_lookup()
thermal: core: thermal_core.h: fix all kernel-doc warnings
thermal: intel: x86_pkg_temp_thermal: Handle invalid temperature
thermal: renesas: rzg3e: add support for RZ/T2H and RZ/N2H
dt-bindings: thermal: r9a09g047-tsu: document RZ/T2H and RZ/N2H
thermal: renesas: rzg3e: make calibration value retrieval per-chip
thermal: renesas: rzg3e: make min and max temperature per-chip
thermal: renesas: rzg3e: make reset optional
dt-bindings: thermal: r9a09g047-tsu: Document RZ/V2N TSU
thermal/drivers/broadcom: Use clamp to simplify bcm2835_thermal_temp2adc
thermal/drivers/stm32: Use predefined HZ_PER_MHZ instead of a custom one
thermal/drivers/mediatek/lvts_thermal: Add mt7987 support
dt-bindings: thermal: mediatek: Add LVTS thermal controller definition for MT7987
dt-bindings: nvmem: mediatek: efuse: Add support for MT8196
thermal/drivers/mediatek/lvts_thermal: Add MT8196 support
thermal/drivers/mediatek/lvts: Support MSR offset for 16-bit calibration data
thermal/drivers/mediatek/lvts: Add support for ATP mode
thermal/drivers/mediatek/lvts: Add lvts_temp_to_raw variant
thermal/drivers/mediatek/lvts: Add platform ops to support alternative conversion logic
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"By the number of commits, cpufreq is the leading party (again) and the
most visible change there is the removal of the omap-cpufreq driver
that has not been used for a long time (good riddance). There are also
quite a few changes in the cppc_cpufreq driver, mostly related to
fixing its frequency invariance engine in the case when the CPPC
registers used by it are not in PCC. In addition to that, support for
AM62L3 is added to the ti-cpufreq driver and the cpufreq-dt-platdev
list is updated for some platforms. The remaining cpufreq changes are
assorted fixes and cleanups.
Next up is cpuidle and the changes there are dominated by intel_idle
driver updates, mostly related to the new command line facility
allowing users to adjust the list of C-states used by the driver.
There are also a few updates of cpuidle governors, including two menu
governor fixes and some refinements of the teo governor, and a
MAINTAINERS update adding Christian Loehle as a cpuidle reviewer.
[Thanks for stepping up Christian!]
The most significant update related to system suspend and hibernation
is the one to stop freezing the PM runtime workqueue during system PM
transitions which allows some deadlocks to be avoided. There is also a
fix for possible concurrent bit field updates in the core device
suspend code and a few other minor fixes.
Apart from the above, several drivers are updated to discard the
return value of pm_runtime_put() which is going to be converted to a
void function as soon as everybody stops using its return value, PL4
support for Ice Lake is added to the Intel RAPL power capping driver,
and there are assorted cleanups, documentation fixes, and some
cpupower utility improvements.
Specifics:
- Remove the unused omap-cpufreq driver (Andreas Kemnade)
- Optimize error handling code in cpufreq_boost_trigger_state() and
make cpufreq_boost_trigger_state() return -EOPNOTSUPP if no policy
supports boost (Lifeng Zheng)
- Update cpufreq-dt-platdev list for tegra, qcom, TI (Aaron Kling,
Dhruva Gole, and Konrad Dybcio)
- Minor improvements to the cpufreq and cpumask rust implementation
(Alexandre Courbot, Alice Ryhl, Tamir Duberstein, and Yilin Chen)
- Add support for AM62L3 SoC to the ti-cpufreq driver (Dhruva Gole)
- Update arch_freq_scale in the CPPC cpufreq driver's frequency
invariance engine (FIE) in scheduler ticks if the related CPPC
registers are not in PCC (Jie Zhan)
- Assorted minor cleanups and improvements in ARM cpufreq drivers
(Juan Martinez, Felix Gu, Luca Weiss, and Sergey Shtylyov)
- Add generic helpers for sysfs show/store to cppc_cpufreq (Sumit
Gupta)
- Make the scaling_setspeed cpufreq sysfs attribute return the actual
requested frequency to avoid confusion (Pengjie Zhang)
- Simplify the idle CPU time granularity test in the ondemand cpufreq
governor (Frederic Weisbecker)
- Enable asym capacity in intel_pstate only when CPU SMT is not
possible (Yaxiong Tian)
- Update the description of rate_limit_us default value in cpufreq
documentation (Yaxiong Tian)
- Add a command line option to adjust the C-states table in the
intel_idle driver, remove the 'preferred_cstates' module parameter
from it, add C-states validation to it and clean it up (Artem
Bityutskiy)
- Make the menu cpuidle governor always check the time till the
closest timer event when the scheduler tick has been stopped to
prevent it from mistakenly selecting the deepest available idle
state (Rafael Wysocki)
- Update the teo cpuidle governor to avoid making suboptimal
decisions in certain corner cases and generally improve idle state
selection accuracy (Rafael Wysocki)
- Remove an unlikely() annotation on the early-return condition in
menu_select() that leads to branch misprediction 100% of the time
on systems with only 1 idle state enabled, like ARM64 servers
(Breno Leitao)
- Add Christian Loehle to MAINTAINERS as a cpuidle reviewer
(Christian Loehle)
- Stop flagging the PM runtime workqueue as freezable to avoid system
suspend and resume deadlocks in subsystems that assume asynchronous
runtime PM to work during system-wide PM transitions (Rafael
Wysocki)
- Drop redundant NULL pointer checks before acomp_request_free() from
the hibernation code handling image saving (Rafael Wysocki)
- Update wakeup_sources_walk_start() to handle empty lists of wakeup
sources as appropriate (Samuel Wu)
- Make dev_pm_clear_wake_irq() check the power.wakeirq value under
power.lock to avoid race conditions (Gui-Dong Han)
- Avoid bit field races related to power.work_in_progress in the core
device suspend code (Xuewen Yan)
- Make several drivers discard pm_runtime_put() return value in
preparation for converting that function to a void one (Rafael
Wysocki)
- Add PL4 support for Ice Lake to the Intel RAPL power capping driver
(Daniel Tang)
- Replace sprintf() with sysfs_emit() in power capping sysfs show
functions (Sumeet Pawnikar)
- Make dev_pm_opp_get_level() return value match the documentation
after a previous update of the latter (Aleks Todorov)
- Use scoped for each OF child loop in the OPP code (Krzysztof
Kozlowski)
- Fix a bug in an example code snippet and correct typos in the
energy model management documentation (Patrick Little)
- Fix miscellaneous problems in cpupower (Kaushlendra Kumar):
* idle_monitor: Fix incorrect value logged after stop
* Fix inverted APERF capability check
* Use strcspn() to strip trailing newline
* Reset errno before strtoull()
* Show C0 in idle-info dump
- Improve cpupower installation procedure by making the systemd step
optional and allowing users to disable the installation of
systemd's unit file (João Marcos Costa)"
* tag 'pm-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
PM: sleep: core: Avoid bit field races related to work_in_progress
PM: sleep: wakeirq: harden dev_pm_clear_wake_irq() against races
cpufreq: Documentation: Update description of rate_limit_us default value
cpufreq: intel_pstate: Enable asym capacity only when CPU SMT is not possible
PM: wakeup: Handle empty list in wakeup_sources_walk_start()
PM: EM: Documentation: Fix bug in example code snippet
Documentation: Fix typos in energy model documentation
cpuidle: governors: teo: Refine intercepts-based idle state lookup
cpuidle: governors: teo: Adjust the classification of wakeup events
cpufreq: ondemand: Simplify idle cputime granularity test
cpufreq: userspace: make scaling_setspeed return the actual requested frequency
PM: hibernate: Drop NULL pointer checks before acomp_request_free()
cpufreq: CPPC: Add generic helpers for sysfs show/store
cpufreq: scmi: Fix device_node reference leak in scmi_cpu_domain_id()
cpufreq: ti-cpufreq: add support for AM62L3 SoC
cpufreq: dt-platdev: Add ti,am62l3 to blocklist
cpufreq/amd-pstate: Add comment explaining nominal_perf usage for performance policy
cpufreq: scmi: correct SCMI explanation
cpufreq: dt-platdev: Block the driver from probing on more QC platforms
rust: cpumask: rename methods of Cpumask for clarity and consistency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block updates from Jens Axboe:
- Support for batch request processing for ublk, improving the
efficiency of the kernel/ublk server communication. This can yield
nice 7-12% performance improvements
- Support for integrity data for ublk
- Various other ublk improvements and additions, including a ton of
selftests additions and updated
- Move the handling of blk-crypto software fallback from below the
block layer to above it. This reduces the complexity of dealing with
bio splitting
- Series fixing a number of potential deadlocks in blk-mq related to
the queue usage counter and writeback throttling and rq-qos debugfs
handling
- Add an async_depth queue attribute, to resolve a performance
regression that's been around for a qhilw related to the scheduler
depth handling
- Only use task_work for IOPOLL completions on NVMe, if it is necessary
to do so. An earlier fix for an issue resulted in all these
completions being punted to task_work, to guarantee that completions
were only run for a given io_uring ring when it was local to that
ring. With the new changes, we can detect if it's necessary to use
task_work or not, and avoid it if possible.
- rnbd fixes:
- Fix refcount underflow in device unmap path
- Handle PREFLUSH and NOUNMAP flags properly in protocol
- Fix server-side bi_size for special IOs
- Zero response buffer before use
- Fix trace format for flags
- Add .release to rnbd_dev_ktype
- MD pull requests via Yu Kuai
- Fix raid5_run() to return error when log_init() fails
- Fix IO hang with degraded array with llbitmap
- Fix percpu_ref not resurrected on suspend timeout in llbitmap
- Fix GPF in write_page caused by resize race
- Fix NULL pointer dereference in process_metadata_update
- Fix hang when stopping arrays with metadata through dm-raid
- Fix any_working flag handling in raid10_sync_request
- Refactor sync/recovery code path, improve error handling for
badblocks, and remove unused recovery_disabled field
- Consolidate mddev boolean fields into mddev_flags
- Use mempool to allocate stripe_request_ctx and make sure
max_sectors is not less than io_opt in raid5
- Fix return value of mddev_trylock
- Fix memory leak in raid1_run()
- Add Li Nan as mdraid reviewer
- Move phys_vec definitions to the kernel types, mostly in preparation
for some VFIO and RDMA changes
- Improve the speed for secure erase for some devices
- Various little rust updates
- Various other minor fixes, improvements, and cleanups
* tag 'for-7.0/block-20260206' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (162 commits)
blk-mq: ABI/sysfs-block: fix docs build warnings
selftests: ublk: organize test directories by test ID
block: decouple secure erase size limit from discard size limit
block: remove redundant kill_bdev() call in set_blocksize()
blk-mq: add documentation for new queue attribute async_dpeth
block, bfq: convert to use request_queue->async_depth
mq-deadline: covert to use request_queue->async_depth
kyber: covert to use request_queue->async_depth
blk-mq: add a new queue sysfs attribute async_depth
blk-mq: factor out a helper blk_mq_limit_depth()
blk-mq-sched: unify elevators checking for async requests
block: convert nr_requests to unsigned int
block: don't use strcpy to copy blockdev name
blk-mq-debugfs: warn about possible deadlock
blk-mq-debugfs: add missing debugfs_mutex in blk_mq_debugfs_register_hctxs()
blk-mq-debugfs: remove blk_mq_debugfs_unregister_rqos()
blk-mq-debugfs: make blk_mq_debugfs_register_rqos() static
blk-rq-qos: fix possible debugfs_mutex deadlock
blk-mq-debugfs: factor out a helper to register debugfs for all rq_qos
blk-wbt: fix possible deadlock to nest pcpu_alloc_mutex under q_usage_counter
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs mount updates from Christian Brauner:
- statmount: accept fd as a parameter
Extend struct mnt_id_req with a file descriptor field and a new
STATMOUNT_BY_FD flag. When set, statmount() returns mount information
for the mount the fd resides on — including detached mounts
(unmounted via umount2(MNT_DETACH)).
For detached mounts the STATMOUNT_MNT_POINT and STATMOUNT_MNT_NS_ID
mask bits are cleared since neither is meaningful. The capability
check is skipped for STATMOUNT_BY_FD since holding an fd already
implies prior access to the mount and equivalent information is
available through fstatfs() and /proc/pid/mountinfo without
privilege. Includes comprehensive selftests covering both attached
and detached mount cases.
- fs: Remove internal old mount API code (1 patch)
Now that every in-tree filesystem has been converted to the new
mount API, remove all the legacy shim code in fs_context.c that
handled unconverted filesystems. This deletes ~280 lines including
legacy_init_fs_context(), the legacy_fs_context struct, and
associated wrappers. The mount(2) syscall path for userspace remains
untouched. Documentation references to the legacy callbacks are
cleaned up.
- mount: add OPEN_TREE_NAMESPACE to open_tree()
Container runtimes currently use CLONE_NEWNS to copy the caller's
entire mount namespace — only to then pivot_root() and recursively
unmount everything they just copied. With large mount tables and
thousands of parallel container launches this creates significant
contention on the namespace semaphore.
OPEN_TREE_NAMESPACE copies only the specified mount tree (like
OPEN_TREE_CLONE) but returns a mount namespace fd instead of a
detached mount fd. The new namespace contains the copied tree mounted
on top of a clone of the real rootfs.
This functions as a combined unshare(CLONE_NEWNS) + pivot_root() in a
single syscall. Works with user namespaces: an unshare(CLONE_NEWUSER)
followed by OPEN_TREE_NAMESPACE creates a mount namespace owned by
the new user namespace. Mount namespace file mounts are excluded from
the copy to prevent cycles. Includes ~1000 lines of selftests"
* tag 'vfs-7.0-rc1.namespace' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
selftests/open_tree: add OPEN_TREE_NAMESPACE tests
mount: add OPEN_TREE_NAMESPACE
fs: Remove internal old mount API code
selftests: statmount: tests for STATMOUNT_BY_FD
statmount: accept fd as a parameter
statmount: permission check should return EPERM
|
|
The my_syscall*() macros are internal implementation details of nolibc.
Now that nolibc has a normal prctl() function, use that.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20260117-nolibc-mysyscall-riscv-v1-1-0ae1ae3513e9@weissschuh.net
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
Add a test to v_ptrace test suite to verify that ptrace accepts the
valid input combinations of vector csr registers. Use kselftest
fixture variants to create multiple inputs for the test.
The test simulates a debug scenario with three breakpoints:
0. init: let the tracee set up its initial vector configuration
1. 1st bp: modify the tracee's vector csr registers from the debugger
- resume the tracee to execute a block without vector instructions
2. 2nd bp: read back the tracees's vector csr registers from the debugger
- compare with values set by the debugger
- resume the tracee to execute a block with vector instructions
3. 3rd bp: read back the tracess's vector csr registers again
- compare with values set by the debugger
The last check helps to confirm that ptrace validation check for vector
csr registers input values works properly and maintains an accurate view
of the tracee's vector context in debugger.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Link: https://patch.msgid.link/20251214163537.1054292-10-geomatsi@gmail.com
[pjw@kernel.org: cleaned up a checkpatch issue]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
Add a test to v_ptrace test suite to verify that ptrace rejects the
invalid input combinations of vector csr registers. Use kselftest
fixture variants to create multiple invalid inputs for the test.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Link: https://patch.msgid.link/20251214163537.1054292-9-geomatsi@gmail.com
[pjw@kernel.org: cleaned up some checkpatch issues]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
Add a test to v_ptrace test suite to verify that vector csr registers
are clobbered on syscalls.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Andy Chiu <andybnac@gmail.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Link: https://patch.msgid.link/20251214163537.1054292-8-geomatsi@gmail.com
[pjw@kernel.org: cleaned up a checkpatch issue]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
Add a test case that attaches to a traced process immediately after its
first executed vector instructions to verify the initial vector context.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Andy Chiu <andybnac@gmail.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Link: https://patch.msgid.link/20251214163537.1054292-7-geomatsi@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
Add a test case to check ptrace behavior in the case when vector
extension is supported by the system, but vector context is not
yet enabled for the traced process.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Andy Chiu <andybnac@gmail.com>
Tested-by: Andy Chiu <andybnac@gmail.com>
Link: https://patch.msgid.link/20251214163537.1054292-6-geomatsi@gmail.com
[pjw@kernel.org: dropped duplicate sys/wait.h include]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs error reporting updates from Christian Brauner:
"This contains the changes to support generic I/O error reporting.
Filesystems currently have no standard mechanism for reporting
metadata corruption and file I/O errors to userspace via fsnotify.
Each filesystem (xfs, ext4, erofs, f2fs, etc.) privately defines
EFSCORRUPTED, and error reporting to fanotify is inconsistent or
absent entirely.
This introduces a generic fserror infrastructure built around struct
super_block that gives filesystems a standard way to queue metadata
and file I/O error reports for delivery to fsnotify.
Errors are queued via mempools and queue_work to avoid holding
filesystem locks in the notification path; unmount waits for pending
events to drain. A new super_operations::report_error callback lets
filesystem drivers respond to file I/O errors themselves (to be used
by an upcoming XFS self-healing patchset).
On the uapi side, EFSCORRUPTED and EUCLEAN are promoted from private
per-filesystem definitions to canonical errno.h values across all
architectures"
* tag 'vfs-7.0-rc1.fserror' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
ext4: convert to new fserror helpers
xfs: translate fsdax media errors into file "data lost" errors when convenient
xfs: report fs metadata errors via fsnotify
iomap: report file I/O errors to the VFS
fs: report filesystem and file I/O errors to fsnotify
uapi: promote EFSCORRUPTED and EUCLEAN to errno.h
|
|
Handle functions that are marked with __exit to prevent warnings:
Documentation/networking/iucv:35: ../net/iucv/iucv.c:1918: WARNING: Error in declarator or parameters
Invalid C declaration: Expecting "(" in parameters. [error at 12]
void __exit iucv_exit (void)
------------^
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20260206065440.2412185-1-rdunlap@infradead.org>
|
|
Test case perftool-testsuite_report fails on s390 for some time
now.
Root cause is a time out which is too tight for large s390 machines.
The time out value addr2line_timeout_ms is per default set to 1 second.
This is the maximum time the function read_addr2line_record() waits for
a reply from the forked off tool addr2line, which is started as a child
in interactive mode.
It reads stdin (an address in hexadecimal) and replies on stdout with
function name, file name and line number. This might take more than one
second.
However one second is not always enough and the reply from addr2line
tool is not received. Function read_addr2line_record() fails and emits
a warning, which is not expected by the test case. It fails.
Output before:
# perf test -F 133
-- [ PASS ] -- perf_report :: setup :: prepare the perf.data file
==================
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.087 MB \
/tmp/perftool-testsuite_report.FHz/perf_report/perf.data.1 \
(207 samples) ]
==================
-- [ PASS ] -- perf_report :: setup :: prepare the perf.data.1 file
## [ PASS ] ## perf_report :: setup SUMMARY
-- [ SKIP ] -- perf_report :: test_basic :: help message :: testcase skipped
Line did not match any pattern: "cmd__addr2line /usr/lib/debug/lib/modules/
6.19.0-20260205.rc8.git366.9845cf73f7db.300.fc43.s390x+next/
vmlinux: could not read first record"
Line did not match any pattern: "cmd__addr2line /usr/lib/debug/lib/modules/
6.19.0-20260205.rc8.git366.9845cf73f7db.300.fc43.s390x+next/
vmlinux: could not read first record"
-- [ FAIL ] -- perf_report :: test_basic :: basic execution
(output regexp parsing)
....
133: perftool-testsuite_report : FAILED!
Output after:
# ./perf test -F 133
-- [ PASS ] -- perf_report :: setup :: prepare the perf.data file
==================
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.087 MB \
/tmp/perftool-testsuite_report.Mlp/perf_report/perf.data.1
(188 samples) ]
==================
-- [ PASS ] -- perf_report :: setup :: prepare the perf.data.1 file
## [ PASS ] ## perf_report :: setup SUMMARY
-- [ SKIP ] -- perf_report :: test_basic :: help message :: testcase skipped
-- [ PASS ] -- perf_report :: test_basic :: basic execution
-- [ PASS ] -- perf_report :: test_basic :: number of samples
-- [ PASS ] -- perf_report :: test_basic :: header
-- [ PASS ] -- perf_report :: test_basic :: header timestamp
-- [ PASS ] -- perf_report :: test_basic :: show CPU utilization
-- [ PASS ] -- perf_report :: test_basic :: pid
-- [ PASS ] -- perf_report :: test_basic :: non-existing symbol
-- [ PASS ] -- perf_report :: test_basic :: symbol filter
-- [ PASS ] -- perf_report :: test_basic :: latency header
-- [ PASS ] -- perf_report :: test_basic :: default report for latency profile
-- [ PASS ] -- perf_report :: test_basic :: latency report for latency profile
-- [ PASS ] -- perf_report :: test_basic :: parallelism histogram
## [ PASS ] ## perf_report :: test_basic SUMMARY
133: perftool-testsuite_report : Ok
#
Fixes: 257046a36750a6db ("perf srcline: Fallback between addr2line implementations")
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: linux-s390@vger.kernel.org
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
$ perf test 'perf data type profiling tests'
83: perf data type profiling tests : Skip
$ perf test -vv 'perf data type profiling tests'
83: perf data type profiling tests:
--- start ---
test child forked, pid 977213
Skip: code_with_type workload not built in 'perf test'
---- end(-2) ----
83: perf data type profiling tests : Skip
$
Cc: Dmitrii Dolgov <9erthalion6@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
One part of the rust code for code_with_type workload wasn't properly
formatted.
Pass it through rustfmt to fix that.
Closes: https://lore.kernel.org/oe-kbuild-all/202602091357.oyRv6hgQ-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
KVM SVM changes for 6.20
- Drop a user-triggerable WARN on nested_svm_load_cr3() failure.
- Add support for virtualizing ERAPS. Note, correct virtualization of ERAPS
relies on an upcoming, publicly announced change in the APM to reduce the
set of conditions where hardware (i.e. KVM) *must* flush the RAP.
- Ignore nSVM intercepts for instructions that are not supported according to
L1's virtual CPU model.
- Add support for expedited writes to the fast MMIO bus, a la VMX's fastpath
for EPT Misconfig.
- Don't set GIF when clearing EFER.SVME, as GIF exists independently of SVM,
and allow userspace to restore nested state with GIF=0.
- Treat exit_code as an unsigned 64-bit value through all of KVM.
- Add support for fetching SNP certificates from userspace.
- Fix a bug where KVM would use vmcb02 instead of vmcb01 when emulating VMLOAD
or VMSAVE on behalf of L2.
- Misc fixes and cleanups.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux
Pull RCU updates from Boqun Feng:
- RCU Tasks Trace:
Re-implement RCU tasks trace in term of SRCU-fast, not only more than
500 lines of code are saved because of the reimplementation, a new
set of API, rcu_read_{,un}lock_tasks_trace(), becomes possible as
well. Compared to the previous rcu_read_{,un}lock_trace(), the new
API avoid the task_struct accesses thanks to the SRCU-fast semantics.
As a result, the old rcu_read{,un}lock_trace() API is now deprecated.
- RCU Torture Test:
- Multiple improvements on kvm-series.sh (parallel run and
progress showing metrics)
- Add context checks to rcu_torture_timer()
- Make config2csv.sh properly handle comments in .boot files
- Include commit discription in testid.txt
- Miscellaneous RCU changes:
- Reduce synchronize_rcu() latency by reporting GP kthread's
CPU QS early
- Use suitable gfp_flags for the init_srcu_struct_nodes()
- Fix rcu_read_unlock() deadloop due to softirq
- Correctly compute probability to invoke ->exp_current()
in rcutorture
- Make expedited RCU CPU stall warnings detect stall-end races
- RCU nocb:
- Remove unnecessary WakeOvfIsDeferred wake path and callback
overload handling
- Extract nocb_defer_wakeup_cancel() helper
* tag 'rcu.release.v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux: (25 commits)
rcu/nocb: Extract nocb_defer_wakeup_cancel() helper
rcu/nocb: Remove dead callback overload handling
rcu/nocb: Remove unnecessary WakeOvfIsDeferred wake path
rcu: Reduce synchronize_rcu() latency by reporting GP kthread's CPU QS early
srcu: Use suitable gfp_flags for the init_srcu_struct_nodes()
rcu: Fix rcu_read_unlock() deadloop due to softirq
rcutorture: Correctly compute probability to invoke ->exp_current()
rcu: Make expedited RCU CPU stall warnings detect stall-end races
rcutorture: Add --kill-previous option to terminate previous kvm.sh runs
rcutorture: Prevent concurrent kvm.sh runs on same source tree
torture: Include commit discription in testid.txt
torture: Make config2csv.sh properly handle comments in .boot files
torture: Make kvm-series.sh give run numbers and totals
torture: Make kvm-series.sh give build numbers and totals
torture: Parallelize kvm-series.sh guest-OS execution
rcutorture: Add context checks to rcu_torture_timer()
rcutorture: Test rcu_tasks_trace_expedite_current()
srcu: Create an rcu_tasks_trace_expedite_current() function
checkpatch: Deprecate rcu_read_{,un}lock_trace()
rcu: Update Requirements.rst for RCU Tasks Trace
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"resctrl test:
- fix division by zero error on Hygon
- fix non-contiguous CBM check for Hygon
- define CPU vendor IDs as bits to match usage
- add CPU vendor detection for Hygon
misc:
- coredeump test: use __builtin_trap() instead of a null pointer
- anon_inode: replace null pointers with empty arrays
- kublk: include message in _Static_assert for C11 compatibility
- run_kselftest.sh: add `--skip` argument option
- pidfd: fix typo in comment"
* tag 'linux_kselftest-next-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/pidfd: fix typo in comment
selftests/run_kselftest.sh: Add `--skip` argument option
selftests/resctrl: Fix non-contiguous CBM check for Hygon
selftests/resctrl: Add CPU vendor detection for Hygon
selftests/resctrl: Define CPU vendor IDs as bits to match usage
selftests/resctrl: Fix a division by zero error on Hygon
kselftest/kublk: include message in _Static_assert for C11 compatibility
kselftest/anon_inode: replace null pointers with empty arrays
kselftest/coredump: use __builtin_trap() instead of null pointer
|
|
KVM selftests changes for 6.20
- Add a regression test for TPR<=>CR8 synchronization and IRQ masking.
- Overhaul selftest's MMU infrastructure to genericize stage-2 MMU support,
and extend x86's infrastructure to support EPT and NPT (for L2 guests).
- Extend several nested VMX tests to also cover nested SVM.
- Add a selftest for nested VMLOAD/VMSAVE.
- Rework the nested dirty log test, originally added as a regression test for
PML where KVM logged L2 GPAs instead of L1 GPAs, to improve test coverage
and to hopefully make the test easier to understand and maintain.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit updates from Shuah Khan:
"kunit:
- add __rust_helper to helpers
- fix up const mismatch in many assert functions
- fix up const mismatch in test_list_sort
- protect KUNIT_BINARY_STR_ASSERTION against ERR_PTR values
- respect KBUILD_OUTPUT env variable by default
- add bash completion
kunit tool:
- add test for nested test result reporting
- do not overwrite test status based on subtest counts
- add 32-bit big endian ARM configuration to qemu_configs
- rename test_data_path() to _test_data_path()
- do not rely on implicit working directory change"
* tag 'linux_kselftest-kunit-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: add bash completion
kunit: tool: test: Don't rely on implicit working directory change
kunit: tool: test: Rename test_data_path() to _test_data_path()
kunit: qemu_configs: Add 32-bit big endian ARM configuration
kunit: tool: Don't overwrite test status based on subtest counts
kunit: tool: Add test for nested test result reporting
kunit: respect KBUILD_OUTPUT env variable by default
kunit: Protect KUNIT_BINARY_STR_ASSERTION against ERR_PTR values
test_list_sort: fix up const mismatch
kunit: fix up const mis-match in many assert functions
rust: kunit: add __rust_helper to helpers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for 7.0
- Add support for FEAT_IDST, allowing ID registers that are not
implemented to be reported as a normal trap rather than as an UNDEF
exception.
- Add sanitisation of the VTCR_EL2 register, fixing a number of
UXN/PXN/XN bugs in the process.
- Full handling of RESx bits, instead of only RES0, and resulting in
SCTLR_EL2 being added to the list of sanitised registers.
- More pKVM fixes for features that are not supposed to be exposed to
guests.
- Make sure that MTE being disabled on the pKVM host doesn't give it
the ability to attack the hypervisor.
- Allow pKVM's host stage-2 mappings to use the Force Write Back
version of the memory attributes by using the "pass-through'
encoding.
- Fix trapping of ICC_DIR_EL1 on GICv5 hosts emulating GICv3 for the
guest.
- Preliminary work for guest GICv5 support.
- A bunch of debugfs fixes, removing pointless custom iterators stored
in guest data structures.
- A small set of FPSIMD cleanups.
- Selftest fixes addressing the incorrect alignment of page
allocation.
- Other assorted low-impact fixes and spelling fixes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson into HEAD
LoongArch KVM changes for v6.20
1. Add more CPUCFG mask bits.
2. Improve feature detection.
3. Add FPU/LBT delay load support.
4. Set default return value in KVM IO bus ops.
5. Add paravirt preempt feature support.
6. Add KVM steal time test case for tools/selftests.
|
|
Features in FEATURE_TESTS_BASIC will be set as being available if
test-all.c builds, so since the rust test isn't included in test-all.c,
we can't have 'rust' in there, remove it from FEATURE_TESTS_BASIC and
use feature-check so that it tries to build test-rust.bin, doing the
actual feature detection.
On a system lacking a rust compiler:
Makefile.config:1158: Rust is not found. Test workloads with rust are disabled.
Auto-detecting system features:
... libdw: [ on ]
... glibc: [ on ]
... libelf: [ on ]
... libnuma: [ on ]
... numa_num_possible_cpus: [ on ]
... libpython: [ on ]
... libcapstone: [ on ]
... llvm-perf: [ on ]
... zlib: [ on ]
... lzma: [ on ]
... bpf: [ on ]
... libaio: [ on ]
... libzstd: [ on ]
... libopenssl: [ on ]
... rust: [ OFF ]
$ cat /tmp/build/perf-tools-next/feature/test-rust.make.output
/bin/sh: line 1: rustc: command not found
$ file /tmp/build/perf-tools-next/feature/test-rust.bin
/tmp/build/perf-tools-next/feature/test-rust.bin: cannot open `/tmp/build/perf-tools-next/feature/test-rust.bin' (No such file or directory)
$
$ perf -vv | grep RUST
rust: [ OFF ] # HAVE_RUST_SUPPORT
$
And after installing it:
... rust: [ on ]
$ cat /tmp/build/perf-tools-next/feature/test-rust.make.output
$ file /tmp/build/perf-tools-next/feature/test-rust.bin
/tmp/build/perf-tools-next/feature/test-rust.bin: ELF 64-bit LSB pie executable, x86-64, version 1 (SYSV), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=9c416edf673ee3705b97bae893a99a6fcf1ee258, for GNU/Linux 3.2.0, with debug_info, not stripped
$
$ perf -vv | grep RUST
rust: [ on ] # HAVE_RUST_SUPPORT
$
Fixes: 6a32fa5ccd33da5d ("tools build: Add a feature test for rust compiler")
Cc: Dmitrii Dolgov <9erthalion6@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The Makefile for the SPI tools creates an include/linux/spi folder and some
symlinks inside it. After running `make -C spi/tools`, this folder shows up
as untracked in the git status.
Add the above folder to the .gitignore file.
Fixes: f325b73dc4db ("spi: tools: move to tools buildsystem")
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Link: https://patch.msgid.link/20260209095001.556495-1-flavra@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Exercise the annotate command with data type profiling feature with C.
For that extend the existing data type profiling shell test to profile
the datasym workload, then annotate the result expecting to see some
data structures from the C code.
Committer testing:
root@number:~# perf test 'perf data type profiling tests'
83: perf data type profiling tests : Ok
root@number:~# perf test -vv 'perf data type profiling tests'
83: perf data type profiling tests:
--- start ---
test child forked, pid 125028
Basic Rust perf annotate test
Basic annotate test [Success]
Pipe Rust perf annotate test
Pipe annotate test [Success]
Basic C perf annotate test
Basic annotate test [Success]
Pipe C perf annotate test
Pipe annotate test [Success]
---- end(0) ----
83: perf data type profiling tests : Ok
root@number:~#
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Exercise the annotate command with data type profiling feature on the
rust runtime. For that add a new shell test, which will profile the
code_with_type workload, then annotate the result expecting to see some
data structures from the rust code.
Committer testing:
root@number:~# perf test 'perf data type profiling tests'
83: perf data type profiling tests : Ok
root@number:~# perf test -v 'perf data type profiling tests'
83: perf data type profiling tests : Ok
root@number:~# perf test -vv 'perf data type profiling tests'
83: perf data type profiling tests:
--- start ---
test child forked, pid 111044
Basic perf annotate test
Basic annotate test [Success]
Pipe perf annotate test
Pipe annotate test [Success]
---- end(0) ----
83: perf data type profiling tests : Ok
root@number:~#
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The purpose of the workload is to gather samples of rust runtime. To
achieve that it has a dummy rust library linked with it.
Per recommendations for such scenarios [1], the rust library is
statically linked.
An example:
$ perf record perf test -w code_with_type
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.160 MB perf.data (4074 samples) ]
$ perf report --stdio --dso perf -s srcfile,srcline
45.16% ub_checks.rs ub_checks.rs:72
6.72% code_with_type.rs code_with_type.rs:15
6.64% range.rs range.rs:767
4.26% code_with_type.rs code_with_type.rs:21
4.23% range.rs range.rs:0
3.99% code_with_type.rs code_with_type.rs:16
[...]
[1]: https://doc.rust-lang.org/reference/linkage.html#mixed-rust-and-foreign-codebases
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add a feature test to identify if the rust compiler is available, so
that perf could build rust based worloads based on that.
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit bb5a920b90991279 ("perf stat: Ensure metrics are displayed even
with failed events") with failed events") made it so that counters which
weren't enabled in the kernel were handled as NaN in metrics.
This caused the "Parse and process metrics" test to start failing as it
wasn't putting a non-zero value in these variables.
Add arbitrary values of 1 to fix the test.
Fixes: bb5a920b90991279 ("perf stat: Ensure metrics are displayed even with failed events")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Chun-Tse Shao <ctshao@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add quotes to avoid the following warning:
```
In tests/shell/record.sh line 264:
[ $(uname -m) = "s390x" ] && {
^---------^ SC2046 (warning): Quote this to prevent word splitting.
For more information:
https://www.shellcheck.net/wiki/SC2046 -- Quote this to prevent word splitt...
```
Fixes: c73a56ed3c97ae65 ("perf test: Fix test case Leader sampling on s390")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar::
- Bump up the Clang minimum version requirements for livepatch
builds, due to Clang assembler section handling bugs causing
silent miscompilations
- Strip livepatching symbol artifacts from non-livepatch modules
- Fix livepatch build warnings when certain Clang LTO options
are enabled
- Fix livepatch build error when CONFIG_MEM_ALLOC_PROFILING_DEBUG=y
* tag 'objtool-urgent-2026-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool/klp: Fix unexported static call key access for manually built livepatch modules
objtool/klp: Fix symbol correlation for orphaned local symbols
livepatch: Free klp_{object,func}_ext data after initialization
livepatch: Fix having __klp_objects relics in non-livepatch modules
livepatch/klp-build: Require Clang assembler >= 20
|
|
This warning can be seen with GCC 15.2:
mptcp_connect.c: In function ‘main_loop’:
mptcp_connect.c:1422:37: warning: ‘peer’ may be used uninitialized [-Wmaybe-uninitialized]
1422 | if (connect(fd, peer->ai_addr, peer->ai_addrlen))
| ~~~~^~~~~~~~~
mptcp_connect.c:1377:26: note: ‘peer’ was declared here
1377 | struct addrinfo *peer;
| ^~~~
This variable is set in sock_connect_mptcp() in some conditions. If not,
this helper returns an error, and the program stops. So this is a false
positive, but better removing it by initialising peer to NULL.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260205-net-mptcp-misc-fixes-6-19-rc8-v2-4-c2720ce75c34@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bpf_local_storage_free() already does not rely on local_storage->smap
since switching to kmalloc_nolock(). As local_storage->smap is removed,
fix the outdated test by dropping the local_storage->smap check. Keep
the second map in task local storage map test to test that multiple
elements can be added to the storage similar to sk storage test.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-18-ameryhung@gmail.com
|
|
bpf_cgrp_storage_busy has been removed. Use bpf_bprintf_nest_level
instead. This percpu variable is also in the bpf subsystem so that
if it is removed in the future, BPF-CI will catch this type of CI-
breaking change.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-17-ameryhung@gmail.com
|
|
Remove a test in test_maps that checks if the updating of the percpu
counter in task local storage map is preemption safe as the percpu
counter is now removed.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-16-ameryhung@gmail.com
|
|
Adjust the error code we are checking against as
bpf_task_storage_delete() now returns -EDEADLK or -ETIMEDOUT when
deadlock happens.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-15-ameryhung@gmail.com
|
|
Update the expected result of the selftest as recursion of task local
storage syscall and helpers have been relaxed. Now that the percpu
counter is removed, task local storage helpers, bpf_task_storage_get()
and bpf_task_storage_delete() can now run on the same CPU at the same
time unless they cause deadlock.
Note that since there is no percpu counter preventing recursion in
task local storage helpers, bpf_trampoline now catches the recursion
of on_update as reported by recursion_misses.
on_enter: tp_btf/sys_enter
on_update: fentry/bpf_local_storage_update
Old behavior New behavior
____________ ____________
on_enter on_enter
bpf_task_storage_get(&map_a) bpf_task_storage_get(&map_a)
bpf_task_storage_trylock succeed bpf_local_storage_update(&map_a)
bpf_local_storage_update(&map_a)
on_update on_update
bpf_task_storage_get(&map_a) bpf_task_storage_get(&map_a)
bpf_task_storage_trylock fail on_update::misses++ (1)
return NULL create and return map_a::ptr
map_a::ptr += 1 (1)
bpf_task_storage_delete(&map_a)
return 0
bpf_task_storage_get(&map_b) bpf_task_storage_get(&map_b)
bpf_task_storage_trylock fail on_update::misses++ (2)
return NULL create and return map_b::ptr
map_b::ptr += 1 (1)
create and return map_a::ptr create and return map_a::ptr
map_a::ptr = 200 map_a::ptr = 200
bpf_task_storage_get(&map_b) bpf_task_storage_get(&map_b)
bpf_task_storage_trylock succeed lockless lookup succeed
bpf_local_storage_update(&map_b) return map_b::ptr
on_update
bpf_task_storage_get(&map_a)
bpf_task_storage_trylock fail
lockless lookup succeed
return map_a::ptr
map_a::ptr += 1 (201)
bpf_task_storage_delete(&map_a)
bpf_task_storage_trylock fail
return -EBUSY
nr_del_errs++ (1)
bpf_task_storage_get(&map_b)
bpf_task_storage_trylock fail
return NULL
create and return ptr
map_b::ptr = 100
Expected result:
map_a::ptr = 201 map_a::ptr = 200
map_b::ptr = 100 map_b::ptr = 1
nr_del_err = 1 nr_del_err = 0
on_update::recursion_misses = 0 on_update::recursion_misses = 2
On_enter::recursion_misses = 0 on_enter::recursion_misses = 0
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-14-ameryhung@gmail.com
|
|
Check sk_omem_alloc when the caller of bpf_local_storage_destroy()
returns. bpf_local_storage_destroy() now returns the memory to uncharge
to the caller instead of directly uncharge. Therefore, in the
sk_storage_omem_uncharge, check sk_omem_alloc when bpf_sk_storage_free()
returns instead of bpf_local_storage_destroy().
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20260205222916.1788211-13-ameryhung@gmail.com
|
|
When building to an output directory the previous code would remove
files and then copy the source files over.
Each source file copy would have a rule to make its directory. All JSON
for every architecture was considered a source file.
This led to unnecessary copying as a file would be deleted and then the
same file copied again, unnecessary directory making, and copying of
files not used in the build.
A side-effect would be a lot of build messages.
This change makes it so that all computed output files are created and
then compared to all files in the OUTPUT directory.
By filtering out the files that would be copied, unnecessary files can
be determined and then deleted - note, this is a phony target which
would remake the pmu-events.c if always depended upon, and so the
dependency is conditional on there being files to remove.
This has some overhead as the $(OUTPUT)/pmu-events is "find" over rather
than just "rm -fr", but the savings from unnecessary copying, etc.
should make up for this new make overhead.
The copy target just does copying but has a dependency on the directory
it needs being built, avoiding repetitive mkdirs.
The source files for copying only consider the JEVENTS_ARCH unless the
JEVENTS_ARCH is all.
The metric JSON is only generated if appropriate, rather than always
being generated and jevents.py deciding whether or not to use the files.
The mypy and pylint targets are fixed as variable names had changed but
the rules not updated.
The line count of a build with "make -C tools/perf O=/tmp/perf clean all"
prior to this change was 2181 lines, after this change it is 1596
lines.
This is a reduction of 585 lines or about 27%.
The generated pmu-events.c for JEVENTS_ARCH "x86" and "all" were
validated as being identical after this change.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Only build vfio self-tests on arm64 and x86_64; these are the only
architectures where the vfio self-tests are run. Addresses compiler
warnings for format and conversions on i386.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202601211830.aBEjmEFD-lkp@intel.com/
Signed-off-by: Ted Logan <tedlogan@fb.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Link: https://lore.kernel.org/r/20260202-vfio-selftest-only-64bit-v2-1-9c3ebb37f0f4@fb.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
