| Age | Commit message (Collapse) | Author |
|---|
|
commit 79989bd4ab86404743953fa382af0a22900050cf upstream.
Usb device connect may not be detected after runtime resume if
xHC is reset during resume.
In runtime resume cases xhci_resume() will only resume roothubs if there
are pending port events. If the xHC host is reset during runtime resume
due to a Save/Restore Error (SRE) then these pending port events won't be
detected as PORTSC change bits are not immediately set by host after reset.
Unconditionally resume roothubs if xHC is reset during resume to ensure
device connections are detected.
Also return early with error code if starting xHC fails after reset.
Issue was debugged and a similar solution suggested by Remi Pommarel.
Using this instead as it simplifies future refactoring.
Reported-by: Remi Pommarel <repk@triplefau.lt>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218987
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240627145523.1453155-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
events without TRB
[ Upstream commit 66cb618bf0bb82859875b00eeffaf223557cb416 ]
Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.
To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34b67198244f2d7d8409fa4eb76204c409c0c97e ]
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 91f7a1524a92c70ffe264db8bdfa075f15bbbeb9 upstream.
As described in commit 8f873c1ff4ca ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ceac4402f5d975e5a01c806438eb4e554771577 upstream.
When multiple streams are in use, multiple TDs might be in flight when
an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for
each, to ensure everything is reset properly and the caches cleared.
Change the logic so that any N>1 TDs found active for different streams
are deferred until after the first one is processed, calling
xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to
queue another command until we are done with all of them. Also change
the error/"should never happen" paths to ensure we at least clear any
affected TDs, even if we can't issue a command to clear the hardware
cache, and complain loudly with an xhci_warn() if this ever happens.
This problem case dates back to commit e9df17eb1408 ("USB: xhci: Correct
assumptions about number of rings per endpoint.") early on in the XHCI
driver's life, when stream support was first added.
It was then identified but not fixed nor made into a warning in commit
674f8438c121 ("xhci: split handling halted endpoints into two steps"),
which added a FIXME comment for the problem case (without materially
changing the behavior as far as I can tell, though the new logic made
the problem more obvious).
Then later, in commit 94f339147fc3 ("xhci: Fix failure to give back some
cached cancelled URBs."), it was acknowledged again.
[Mathias: commit 94f339147fc3 ("xhci: Fix failure to give back some cached
cancelled URBs.") was a targeted regression fix to the previously mentioned
patch. Users reported issues with usb stuck after unmounting/disconnecting
UAS devices. This rolled back the TD clearing of multiple streams to its
original state.]
Apparently the commit author was aware of the problem (yet still chose
to submit it): It was still mentioned as a FIXME, an xhci_dbg() was
added to log the problem condition, and the remaining issue was mentioned
in the commit description. The choice of making the log type xhci_dbg()
for what is, at this point, a completely unhandled and known broken
condition is puzzling and unfortunate, as it guarantees that no actual
users would see the log in production, thereby making it nigh
undebuggable (indeed, even if you turn on DEBUG, the message doesn't
really hint at there being a problem at all).
It took me *months* of random xHC crashes to finally find a reliable
repro and be able to do a deep dive debug session, which could all have
been avoided had this unhandled, broken condition been actually reported
with a warning, as it should have been as a bug intentionally left in
unfixed (never mind that it shouldn't have been left in at all).
> Another fix to solve clearing the caches of all stream rings with
> cancelled TDs is needed, but not as urgent.
3 years after that statement and 14 years after the original bug was
introduced, I think it's finally time to fix it. And maybe next time
let's not leave bugs unfixed (that are actually worse than the original
bug), and let's actually get people to review kernel commits please.
Fixes xHC crashes and IOMMU faults with UAS devices when handling
errors/faults. Easiest repro is to use `hdparm` to mark an early sector
(e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop.
At least in the case of JMicron controllers, the read errors end up
having to cancel two TDs (for two queued requests to different streams)
and the one that didn't get cleared properly ends up faulting the xHC
entirely when it tries to access DMA pages that have since been unmapped,
referred to by the stale TDs. This normally happens quickly (after two
or three loops). After this fix, I left the `cat` in a loop running
overnight and experienced no xHC failures, with all read errors
recovered properly. Repro'd and tested on an Apple M1 Mac Mini
(dwc3 host).
On systems without an IOMMU, this bug would instead silently corrupt
freed memory, making this a security bug (even on systems with IOMMUs
this could silently corrupt memory belonging to other USB devices on the
same controller, so it's still a security bug). Given that the kernel
autoprobes partition tables, I'm pretty sure a malicious USB device
pretending to be a UAS device and reporting an error with the right
timing could deliberately trigger a UAF and write to freed memory, with
no user action.
[Mathias: Commit message and code comment edit, original at:]
https://lore.kernel.org/linux-usb/20240524-xhci-streams-v1-1-6b1f13819bea@marcan.st/
Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Fixes: 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs.")
Fixes: 674f8438c121 ("xhci: split handling halted endpoints into two steps")
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17bd54555c2aaecfdb38e2734149f684a73fa584 upstream.
As described in commit c877b3b2ad5c ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0260589b439e2637ad54a2b25f00a516ef28a57 upstream.
The transferred length is set incorrectly for cancelled bulk
transfer TDs in case the bulk transfer ring stops on the last transfer
block with a 'Stop - Length Invalid' completion code.
length essentially ends up being set to the requested length:
urb->actual_length = urb->transfer_buffer_length
Length for 'Stop - Length Invalid' cases should be the sum of all
TRB transfer block lengths up to the one the ring stopped on,
_excluding_ the one stopped on.
Fix this by always summing up TRB lengths for 'Stop - Length Invalid'
bulk cases.
This issue was discovered by Alan Stern while debugging
https://bugzilla.kernel.org/show_bug.cgi?id=218890, but does not
solve that bug. Issue is older than 4.10 kernel but fix won't apply
to those due to major reworks in that area.
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Cc: stable@vger.kernel.org # v4.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db4460b6ecf07574d580f01cd88054a62607068c ]
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230ad ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci_plat.h should not need to include the entire xhci.h header.
This can cause redefinition in dwc3 if it selectively includes some xHCI
definitions. This is a prerequisite change for a fix to disable suspend
during initialization for dwc3.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/310acfa01c957a10d9feaca3f7206269866ba2eb.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pointer from a xhci usb virt device to its root hub port
(vdev->rhub_port) is set later when device is addressed, not while
vdev is allocated.
Tracepoints dereferenced this rhub_port pointer when freeing the virt
device, which causes null pointer dereference if tracing is enabled
and device is freed before addressed.
This can happen if tracing is enabled and xhci driver is unloaded before
a device is fully enumerated, or initial enumeration fails and device
is reset and freed before retry.
Don't dereference the rhub_port or show port numbers when tracing
xhci_free_virt_device(). This info is not very useful anyway.
Print the more useful slot id instead
Fixes: 06790c19086f ("xhci: replace real & fake port with pointer to root hub port")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20240402005007.klv2ij727fkz7rpd@synopsys.com/
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we get STS_HCE we give up on the interrupt, but for the purpose
of IRQ handling that still counts as ours. We may return IRQ_NONE
only if we are positive that it wasn't ours. Hence correct the default.
Fixes: 2a25e66d676d ("xhci: print warning when HCE was set")
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307112406.3625756-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable runtime PM by default for older AMD 1022:43f7 xHCI 1.1 host as it
is proven to work.
Driver enables runtime PM by default for newer xHCI 1.2 host.
Link: https://lore.kernel.org/all/12335218.O9o76ZdvQC@natalenko.name/
Cc: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240304054327.2564500-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f0609 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e58472 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DbC driver starts polling for events immediately when DbC is enabled.
The current polling interval is 1ms, which keeps the CPU busy, impacting
power management even when there are no active data transfers.
Solve this by polling at a slower rate, with a 64ms interval as default
until a transfer request is queued, or if there are still are pending
unhandled transfers at event completion.
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two NEC uPD720200 adapters have been observed to randomly misbehave:
a Stop Endpoint command fails with Context Error, the Output Context
indicates Stopped state, and the endpoint keeps running. Very often,
Set TR Dequeue Pointer is seen to fail next with Context Error too,
in addition to problems from unexpectedly completed cancelled work.
The pathology is common on fast running isoc endpoints like uvcvideo,
but has also been reproduced on a full-speed bulk endpoint of pl2303.
It seems all EPs are affected, with risk proportional to their load.
Reproduction involves receiving any kind of stream and closing it to
make the device driver cancel URBs already queued in advance.
Deal with it by retrying the command like in the Running state.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A trb_in_td() call is used to determine if a completion event matches
any TRB of the currently executing TD. This function is told to start
searching right after the last finished TD, which is not at all where
the currently expected TD is guaranteed to begin, because some TDs in
between may have been cancelled.
Not only is a pointless work performed, but a bug resulting in the HC
executing cancelled TDs was seen to trick the driver into associating
events from a TD just cancelled with an unrelated future TD.
Since the ring is being traversed for the specific purpose of finding
a match with the current TD, always start from its first TRB. This is
the most reliable bit of information that we posses.
Tracking of HC's work progress is not affected, except for cases when
a misattributed event would have moved dequeue past a pending TD.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor the code to improve readability by using
'xhci_free_segments_for_ring()' function for freeing ring segments.
This replaces the custom while loop previously used within
'xhci_ring_expansion()' and 'xhci_alloc_segments_for_ring()'.
Slightly modify 'xhci_free_segments_for_ring()' to handle lists
which do not loop. This makes it possible to use it in error
paths of 'xhci_alloc_segments_for_ring()'.
This change also prepares for switching the custom xhci linked segment
list into to more standard list.h lists.
[minor commit message rewording -Mathias]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace a segment of code within 'xhci_clear_command_ring()' with a
function call to 'xhci_initialize_ring_info()'. This change eliminates
code duplication, as 'xhci_initialize_ring_info()' performs the same
operations as the replaced code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variables real & fake port do not convey their purpose, thus they are
replaced with a pointer to the root hub port 'struct xhci_port *rhub_port'.
'rhub_port' contains real & fake ports in zero-based format, which happens
to be more widely used inside the xHCI driver:
- 'real_port' is ('rhub_port->hw_portnum' + 1)
- 'fake_port' is ('rhub_port->hcd_portnum' + 1)
One reason for real port being one-based, is to signal other functions in
case struct 'xhci_virt_device' initialization failed, in this case the
value will remain 0. This is no longer needed, instead we check whether
or not 'rhub_port' is 'NULL'.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC hardware needs to know which roothub port a USB device is attached to
when controlling the device, so the xHCI driver stores in each device the
roothub port which it's connected behind. This is done with two different
port index values, the 'real_port' which is an index to the xHC hardware
port register array, and the 'fake_port' which is the per hub port index
used by the hub driver.
Instead of finding real & fake port separately, find the root hub port
'xhci_port' structure which contains both real & fake port values:
- 'real_port' is ('hw_portnum' + 1)
- 'fake_port' is ('hcd_portnum' + 1)
i.e. real & fake port are 'hw_portnum' & 'hcd_portnum' in one-based
format.
The 'xhci_port' structure is a better way to refer to roothub ports than
the 'real_port' & 'fake_port'. As a result, these port indexes are slated
to be replaced with a direct pointer to the root hub port. This patch
setups the ground work for the future changes.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need it here for the USB fixes, and it resolves a merge conflict as
reported in linux-next in drivers/usb/roles/class.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 9affb1d9a9d9918adff519a129daba5e369dd741.
It's not ready to be merged, based on reviews.
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/96ab6033-2cb9-daa7-ddad-090138896739@linux.intel.com
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes relying upon linux/of_platform.h to include
linux/platform_device.h, which it no longer does, thereby fixing
compilation problems like:
In file included from drivers/usb/host/uhci-hcd.c:850:
drivers/usb/host/uhci-grlib.c: In function 'uhci_hcd_grlib_probe':
drivers/usb/host/uhci-grlib.c:92:29: error: invalid use of undefined type 'struct platform_device'
92 | struct device_node *dn = op->dev.of_node;
| ^~
Fixes: ef175b29a242 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240129075056.1511630-1-andreas@gaisler.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some sequences, will require traversing through the entire event ring
without handling the event TRB. This is ideal for when secondary
interrupters that are utilized by external entities need to clean up the
interrupter's event rings during halting of the XHCI HCD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-10-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check if the event ring exists and is valid once when the event handler
is called, not before every individual event TRB.
At this point the interrupter is valid, so no need to check that.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-9-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add unhandled_event_trb() that returns true in case xHC hardware has
written new event trbs to the event ring that driver has not yet handled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-8-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the main XHCI interrupt handler into a different API, so that other
potential interrupters can utilize similar event ring handling. A scenario
would be if a secondary interrupter required to skip pending events in the
event ring, which would warrant a similar set of operations.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The event ring dequeue pointer field (ERDP) in xHC hardware is used to
inform controller how far the driver has processed events on the event
ring.
In the case all events are handled and event ring is empty then the
address of the TRB after the last processed one should be written.
This TRB is both the enqueue and dequeue pointer.
But in case we are writing the ERDP in the middle of processing
several events then ERDP field should be written with the "up to and
including" address of the last handled event TRB.
Currenly each ERDP write by driver is done as if all events are handled
and ring is empty.
Fix this by adjusting the order when software dequeue "inc_deq()"
is called and hardware dequeue "xhci_update_erst_dequeue()" is updated.
Details in xhci 1.2 specification section 4.9.4:
"System software shall write the Event Ring Dequeue Pointer (ERDP)
register to inform the xHC that it has completed the processing of Event
TRBs up to and including the Event TRB referenced by the ERDP.
The detection of a Cycle bit mismatch in an Event TRB processed by
software indicates the location of the xHC Event Ring Enqueue Pointer
and that the Event Ring is empty. Software shall write the ERDP with
the address of this TRB to indicate that it has processed all Events
in the ring"
This change depends on fixes made to relocate inc_deq() calls captured
in the below commits:
commit 3321f84bfae0 ("xhci: simplify event ring dequeue tracking for
transfer events")
commit d1830364e963 ("xhci: Simplify event ring dequeue pointer update
for port change events")
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The event_ring_deq parameter is used to check if the event ring dequeue
position is updated while calling by xhci_handle_event(), meaning there was
an actual event on the ring to handle. In this case the driver needs to
inform hardware about the updated dequeue position.
Basically event_ring_deq just stores the old event ring dequeue position
before calling the event handler.
Keeping track of software event dequeue updates this way is no longer
useful as driver anyways reads the current hardware dequeue position
within the handle event, and checks if it needs to be updated.
The driver might anyway need to modify the EHB (event handler busy) bit in
the same register as the dequeue pointer even if the actual dequeue
position did not change.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a helper to set the interrupt moderation interval for an interrupter.
Each interrupter can have its own moderation value.
Hardware has a 16bit register for the moderation value, each step is 250ns.
Helper function imod_interval argument is in nanoseconds.
Values from 0 to 16383750 (250 x 0xffff) are accepted.
0 means no interrupt throttling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for ac5 to the EHCI Orion platform driver.
The ac5 SOC has DDR starting at offset 0x2_0000_0000,
Hence it requires a larger than 32-bit DMA mask to operate.
Move the dma mask to be pointed by the OF match data, and
use that match data when initializng the DMA mask.
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240114172154.2622275-3-enachman@marvell.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sanity check of interrupter index when adding a new interrupter is
off by one. intr_num needs to be smaller than xhci->max_interrupter to
fit the array of interrupters.
Luckily this doesn't cause any real word harm as xhci_add_interrupter()
is always called with a intr_num value smaller than xhci->max_interrupters
in any current kernel.
Should not be needed for stable as 6.7 kernel and older only supports
one interrupter, with intr_num always being zero.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/e9771296-586d-456a-ac24-a82de79bb2e6@moroto.mountain/
Fixes: 4bf398e15aa4 ("xhci: split allocate interrupter into separate alloacte and add parts")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't try to remove a secondary interrupter that is known to be invalid.
Also check if the interrupter is valid inside the spinlock that protects
the array of interrupters.
Found by smatch static checker
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/ffaa0a1b-5984-4a1f-bfd3-9184630a97b9@moroto.mountain/
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Upstream commit bac1ec551434 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec551434 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Quite a lot of kexec work this time around. Many singleton patches in
many places. The notable patch series are:
- nilfs2 folio conversion from Matthew Wilcox in 'nilfs2: Folio
conversions for file paths'.
- Additional nilfs2 folio conversion from Ryusuke Konishi in 'nilfs2:
Folio conversions for directory paths'.
- IA64 remnant removal in Heiko Carstens's 'Remove unused code after
IA-64 removal'.
- Arnd Bergmann has enabled the -Wmissing-prototypes warning
everywhere in 'Treewide: enable -Wmissing-prototypes'. This had
some followup fixes:
- Nathan Chancellor has cleaned up the hexagon build in the series
'hexagon: Fix up instances of -Wmissing-prototypes'.
- Nathan also addressed some s390 warnings in 's390: A couple of
fixes for -Wmissing-prototypes'.
- Arnd Bergmann addresses the same warnings for MIPS in his series
'mips: address -Wmissing-prototypes warnings'.
- Baoquan He has made kexec_file operate in a top-down-fitting manner
similar to kexec_load in the series 'kexec_file: Load kernel at top
of system RAM if required'
- Baoquan He has also added the self-explanatory 'kexec_file: print
out debugging message if required'.
- Some checkstack maintenance work from Tiezhu Yang in the series
'Modify some code about checkstack'.
- Douglas Anderson has disentangled the watchdog code's logging when
multiple reports are occurring simultaneously. The series is
'watchdog: Better handling of concurrent lockups'.
- Yuntao Wang has contributed some maintenance work on the crash code
in 'crash: Some cleanups and fixes'"
* tag 'mm-nonmm-stable-2024-01-09-10-33' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (157 commits)
crash_core: fix and simplify the logic of crash_exclude_mem_range()
x86/crash: use SZ_1M macro instead of hardcoded value
x86/crash: remove the unused image parameter from prepare_elf_headers()
kdump: remove redundant DEFAULT_CRASH_KERNEL_LOW_SIZE
scripts/decode_stacktrace.sh: strip unexpected CR from lines
watchdog: if panicking and we dumped everything, don't re-enable dumping
watchdog/hardlockup: use printk_cpu_sync_get_irqsave() to serialize reporting
watchdog/softlockup: use printk_cpu_sync_get_irqsave() to serialize reporting
watchdog/hardlockup: adopt softlockup logic avoiding double-dumps
kexec_core: fix the assignment to kimage->control_page
x86/kexec: fix incorrect end address passed to kernel_ident_mapping_init()
lib/trace_readwrite.c:: replace asm-generic/io with linux/io
nilfs2: cpfile: fix some kernel-doc warnings
stacktrace: fix kernel-doc typo
scripts/checkstack.pl: fix no space expression between sp and offset
x86/kexec: fix incorrect argument passed to kexec_dprintk()
x86/kexec: use pr_err() instead of kexec_dprintk() when an error occurs
nilfs2: add missing set_freezable() for freezable kthread
kernel: relay: remove relay_file_splice_read dead code, doesn't work
docs: submit-checklist: remove all of "make namespacecheck"
...
|
|
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
