| Age | Commit message (Collapse) | Author |
|---|
|
Improve support for system suspend. The register information has been
extracted from the ACPI DSDT code handling Windows Modern Standby. I
took over the weird multi-write function from the ACPI DSDT code where
it is called ECWS.
In addition to writing to the 0xE0 register, the ACPI Windows Modern
Standby code also does some changes to the thermal configuration. This
part is not implemented.
After this patch the laptop's power and LID LEDs will switch into the
typical breathing animation when the system is suspended and enabled
normally again after resuming.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Link: https://patch.msgid.link/20251119-thinkpad-t14s-ec-improvements-v2-3-441219857c02@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Module asus-armoury must use AC tunables to check availability
of power-related firmware attributes: fix missing attributes
by using AC attributes instead of DC.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Link: https://patch.msgid.link/20251123150535.267339-1-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
This passes the address of the pointer "&punit_ipcdev" when the intent
was to pass the pointer itself "punit_ipcdev" (without the ampersand).
This means that the:
complete(&ipcdev->cmd_complete);
in intel_punit_ioc() will write to a wrong memory address corrupting it.
Fixes: fdca4f16f57d ("platform:x86: add Intel P-Unit mailbox IPC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSCmoBipSQ_tlD-D@stanley.mountain
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The ACPI ECRD and ECWR functions have a 10ms sleep at the end. It turns
out, that this is sometimes needed to avoid I2C transmission failures,
especially for functions doing regmap_update_bits (and thus read + write
shortly after each other). This fixes problems like the following
appearing in the kernel log:
leds platform::micmute: Setting an LED's brightness failed (-6)
leds platform::kbd_backlight: Setting an LED's brightness failed (-6)
The ACPI QEVT function used to read the interrupt status register also
has a 10ms sleep at the end. Without that there are problems with
reading multiple events following directly after each other resulting
in the following error message being logged:
thinkpad-t14s-ec 4-0028: Failed to read event
Fixes: 60b7ab6ce030 ("platform: arm64: thinkpad-t14s-ec: new driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Link: https://patch.msgid.link/20251119-thinkpad-t14s-ec-improvements-v2-2-441219857c02@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Fix a race condition, that an input key related interrupt might be
triggered before the input handler has been registered, which results
in a NULL pointer dereference. This can happen if the user enables
the keyboard backlight shortly before the driver is being probed.
This fixes the following backtrace visible in dmesg:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e0
...
Call trace:
sparse_keymap_report_event+0x2c/0x978 [sparse_keymap] (P)
t14s_ec_irq_handler+0x190/0x3e8 [lenovo_thinkpad_t14s]
irq_thread_fn+0x30/0xb8
irq_thread+0x18c/0x3b0
kthread+0x148/0x228
ret_from_fork+0x10/0x20
Fixes: 60b7ab6ce030 ("platform: arm64: thinkpad-t14s-ec: new driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Bryan O'Donoghue <bod@kernel.org>
Link: https://patch.msgid.link/20251119-thinkpad-t14s-ec-improvements-v2-1-441219857c02@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The Ayaneo EC resets after hibernation, losing the charge control state.
Add a small PM hook to restore this state on hibernation resume.
The fan speed is also lost during hibernation, but since hibernation
failures are common with this class of devices, setting a low fan speed
when the userspace program controlling the fan will potentially not
take over could cause the device to overheat, so it is not restored.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-7-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Currently, the oxpec driver contains Ayaneo devices. Move them to the
new ayaneo-ec driver, which is dedicated to them.
As this driver supports charge inhibition for Ayaneo, add support for it
for the AIR, AIR 1S, AB05-Medoncino, AIR Pro, and Kun, referenced from
the out-of-tree ayaneo-platform driver.
In addition, update the readmes of oxpec to reflect this change.
Link: https://github.com/ShadowBlip/ayaneo-platform
Tested-by: Derek J. Clark <derekjohn.clark@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-6-lkml@antheas.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The Ayaneo 3 features hot-swappable controller modules. The ejection
and management is done through HID. However, after ejecting the modules,
the controller needs to be power cycled via the EC to re-initialize.
For this, the EC provides a variable that holds whether the left or
right modules are connected, and a power control register to turn
the controller on or off. After ejecting the modules, the controller
should be turned off. Then, after both modules are reinserted,
the controller may be powered on again to re-initialize.
This patch introduces two new sysfs attributes:
- `controller_modules`: a read-only attribute that indicates whether
the left and right modules are connected (none, left, right, both).
- `controller_power`: a read-write attribute that allows the user
to turn the controller on or off (with '1'/'0').
Therefore, after ejection is complete, userspace can power off the
controller, then wait until both modules have been reinserted
(`controller_modules` will return 'both') to turn on the controller.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-5-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Ayaneo devices support charge inhibition via the EC. This inhibition
only works while the device is powered on, and resets between restarts.
However, it is maintained across suspend/resume cycles.
The EC does not support charge threshold control. Instead, userspace
software on Windows manually toggles charge inhibition depending on
battery level.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-4-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add hwmon single fan sensor reads and control for Ayaneo devices.
The register and method of access is the same for all devices.
Reviewed-by: Armin-Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-3-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Recent Ayaneo devices feature an ACPI mapped Embedded Controller (EC)
with standard addresses across models that provides access to fan
speed, fan control, battery charge limits, and controller power
controls. Introduce a new driver stub that will handle these driver
features.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://patch.msgid.link/20251119174505.597218-2-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
https://git.pengutronix.de/git/pza/linux into gpio/for-next
Reset/GPIO/swnode changes for v6.19 (v2)
* Fix chtwc_int33fe build issue since commit d7cdbbc93c56 ("software
node: allow referencing firmware nodes").
|
|
Add TDP data for laptop mode FA507UV.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Link: https://patch.msgid.link/20251120025413.1686540-1-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Perform the actual check of the mini-led mode against supported modes
and do not return the first one regardless of the WMI devstate.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/aR1xbxEQyQPEvB9o@stanley.mountain/
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Link: https://patch.msgid.link/20251120024059.1341326-1-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
mini_led_mode_current_value_store()
There are two return statements in a row here. The first one is wrong
so delete that one. This changes the return value to -ENODEV.
Fixes: f99eb098090e ("platform/x86: asus-armoury: move existing tunings to asus-armoury module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSBqRHs256Tz7EKr@stanley.mountain
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add METRICS_TABLE_ID (7) and use it when requesting the metrics
transfer table instead of the hard-coded literal. This clarifies the
meaning of the argument to amd_pmf_send_cmd() and centralizes the table
ID definition for easier maintenance.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251120105210.3945710-4-Shyam-sundar.S-k@amd.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add SET_CMD and GET_CMD constants and replace boolean values passed as the
get/set argument to amd_pmf_send_cmd() with the new explicit flags. This
improves readability, avoids ambiguity around true/false and 0/1 usage.
There is no functional change.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://patch.msgid.link/20251120105210.3945710-3-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Update smu_pmf_metrics_v2 to use NPU terminology instead of IPU. This
aligns the driver with current firmware/hardware naming and fixes the
mismatch. There is no functional change and no impact to the struct layout
and only field names are updated.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by:
Link: https://patch.msgid.link/20251120105210.3945710-2-Shyam-sundar.S-k@amd.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Members of struct software_node_ref_args should not be dereferenced
directly but set using the provided macros. Commit d7cdbbc93c56
("software node: allow referencing firmware nodes") changed the name of
the software node member and caused a build failure. Remove all direct
dereferences of the ref struct as a fix.
However, this driver also seems to abuse the software node interface by
waiting for a node with an arbitrary name "intel-xhci-usb-sw" to appear
in the system before setting up the reference for the I2C device, while
the actual software node already exists in the intel-xhci-usb-role-switch
module and should be used to set up a static reference. Add a FIXME for
a future improvement.
Fixes: d7cdbbc93c56 ("software node: allow referencing firmware nodes")
Fixes: 53c24c2932e5 ("platform/x86: intel_cht_int33fe: use inline reference properties")
Cc: stable@vger.kernel.org
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/all/20251121111534.7cdbfe5c@canb.auug.org.au/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
into gpio/for-next
Reset/GPIO/swnode changes for v6.19
* Extend software node implementation, allowing its properties to reference
existing firmware nodes.
* Update the GPIO property interface to use reworked swnode macros.
* Rework reset-gpio code to use GPIO lookup via swnode.
* Fix spi-cs42l43 driver to work with swnode changes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Ilpo Järvinen:
"This one has lots of new HW entries which adds to the size in diffstat
but the individual changes are simple.
Fixes
- acer-wmi: Ignore backlight event
- alienware-wmi-wmax: Fix quirk match table order & drop redundant
entries
- amd/pmc:
- Add Xbox Ally to spurious 8042 quirk list
- Quirk list Lenovo Legion Go 2 NVMe resume
- msi-wmi-platform:
- Correct GUID to uppercase
- GUID is uncleverly copy-pasted from an example so add a DMI
whitelist
- intel/speed_select_if: PCIBIOS_* return code conversion
- intel-uncore-freq & ISST: Fix kernel doc warnings
New HW support
- alienware-wmi-wmax:
- Alienware 16 Aurora support
- Alienware M support
- Alienware X support
- Dell G support
- amd/pmc:
- ROG Xbox Ally (non-X) support
- huaway-wmi: HONOR MagicBoox X16/X14 PrintScreen & YOYO keys
- hp-wmi:
- Omen 16-wf1xxx fan support
- Omen MAX 16-ah0xx fan + thermal profile support
- Victus 16-r0 and 16-s0 fan + thermal profile support
- intel/hid: Intel Nova Lake support
- intel-uncore-freq:
- Intel Panther Lake support
- Intel Wildcat Lake support
- Intel Nova Lake support"
* tag 'platform-drivers-x86-v6.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (21 commits)
platform/x86: intel-uncore-freq: fix all header kernel-doc warnings
platform/x86: acer-wmi: Ignore backlight event
platform/x86/intel/speed_select_if: Convert PCIBIOS_* return codes to errnos
platform/x86/intel/hid: Add Nova Lake support
platform/x86: alienware-wmi-wmax: Add AWCC support to Alienware 16 Aurora
platform/x86: hp-wmi: Add Omen MAX 16-ah0xx fan support and thermal profile
platform/x86: msi-wmi-platform: Fix typo in WMI GUID
platform/x86: msi-wmi-platform: Only load on MSI devices
platform/x86/amd: pmc: Add Lenovo Legion Go 2 to pmc quirk list
platform/x86/amd/pmc: Add spurious_8042 to Xbox Ally
platform/x86/amd/pmc: Add support for Van Gogh SoC
platform/x86: alienware-wmi-wmax: Add support for the whole "G" family
platform/x86: alienware-wmi-wmax: Add support for the whole "X" family
platform/x86: alienware-wmi-wmax: Add support for the whole "M" family
platform/x86: alienware-wmi-wmax: Drop redundant DMI entries
platform/x86: alienware-wmi-wmax: Fix "Alienware m16 R1 AMD" quirk order
platform/x86: ISST: isst_if.h: fix all kernel-doc warnings
platform/x86: intel-uncore-freq: Add additional client processors
platform/x86: hp-wmi: Add Omen 16-wf1xxx fan support
platform/x86: huawei-wmi: add keys for HONOR models
...
|
|
Intel Elkhart Lake Programmable Service Engine (PSE) includes two PCI
devices that expose two different capabilities of GPIO and Timed I/O
as a single PCI function through shared MMIO with below layout.
GPIO: 0x0000 - 0x1000
TIO: 0x1000 - 0x2000
This driver enumerates the PCI parent device and creates auxiliary child
devices for these capabilities. The actual functionalities are provided
by their respective auxiliary drivers.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20251112034040.457801-2-raag.jadav@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Move the WMI core code into a separate directory to prepare for
future additions to the WMI driver. Also update the description
of the Kconfig entry to better fit with the other subsystem
Kconfig entries.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251111131125.3379-5-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
When evaluating a WMxx/WSxx ACPI control method, the data buffer
either needs to be passed as an ACPI buffer or as an ACPI string.
Use the correct type (buffer/string) when populating the associated
ACPI object.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251111131125.3379-3-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Adds the ppt_* and nv_* tuning knobs that are available via WMI methods
and adds proper min/max levels plus defaults.
The min/max are defined by ASUS and typically gained by looking at what
they allow in the ASUS Armoury Crate application - ASUS does not share
the values outside of this. It could also be possible to gain the AMD
values by use of ryzenadj and testing for the minimum stable value.
The general rule of thumb for adding to the match table is that if the
model range has a single CPU used throughout, then the DMI match can
omit the last letter of the model number as this is the GPU model.
If a min or max value is not provided it is assumed that the particular
setting is not supported. for example ppt_pl2_sppt_min/max is not set.
If a <ppt_setting>_def is not set then the default is assumed to be
<ppt_setting>_max
It is assumed that at least AC settings are available so that the
firmware attributes will be created - if no DC table is available
and power is on DC, then reading the attributes is -ENODEV.
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mateusz Schyboll <dragonn@op.pl>
Tested-by: Porfet Lillian <porfet828@gmail.com>
Link: https://patch.msgid.link/20251102215319.3126879-10-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Maintain power-related WMI macros naming consistency:
rename ASUS_WMI_DEVID_PPT_FPPT to ASUS_WMI_DEVID_PPT_PL3_FPPT.
Link: https://lore.kernel.org/all/cad7b458-5a7a-4975-94a1-d0c74f6f3de5@oracle.com/
Suggested-by: ALOK TIWARI <alok.a.tiwari@oracle.com>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Link: https://.../
Link: https://patch.msgid.link/20251102215319.3126879-9-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
With the existence of the asus-armoury module the attributes no longer
need to live under the /sys/devices/platform/asus-nb-wmi/ path.
Deprecate all those that were implemented in asus-bioscfg with the goal
of removing them fully in the next LTS cycle.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20251102215319.3126879-8-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add screen_auto_brightness toggle supported on some laptops.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251102215319.3126879-7-denis.benato@linux.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Implement the APU memory size control under the asus-armoury module using
the fw_attributes class.
This allows the APU allocated memory size to be adjusted depending on
the users priority. A reboot is required after change.
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://patch.msgid.link/20251102215319.3126879-5-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
In file uncore-frequency/uncore-frequency-common.h,
correct all kernel-doc warnings by adding missing leading " *" to some
lines, adding a missing kernel-doc entry, and fixing a name typo.
Warning: uncore-frequency-common.h:50 bad line:
Storage for kobject attribute elc_low_threshold_percent
Warning: uncore-frequency-common.h:52 bad line:
Storage for kobject attribute elc_high_threshold_percent
Warning: uncore-frequency-common.h:54 bad line:
Storage for kobject attribute elc_high_threshold_enable
Warning: uncore-frequency-common.h:92 struct member
'min_freq_khz_kobj_attr' not described in 'uncore_data'
Warning: uncore-frequency-common.h:92 struct member
'die_id_kobj_attr' not described in 'uncore_data'
Fixes: 24b6616355f7 ("platform/x86/intel-uncore-freq: Add efficiency latency control to sysfs interface")
Fixes: 416de0246f35 ("platform/x86: intel-uncore-freq: Fix types in sysfs callbacks")
Fixes: 247b43fcd872 ("platform/x86/intel-uncore-freq: Add attributes to show die_id")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20251111060938.1998542-1-rdunlap@infradead.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
On the Acer Nitro AN515-58, the event 4 - 0 is send by the ACPI
firmware when the backlight up/down keys are pressed. Ignore this
event to avoid spamming the kernel log with error messages, as the
acpi-video driver already handles brightness up/down events.
Reported-by: Bugaddr <Bugaddr@protonmail.com>
Closes: https://bugaddr.tech/posts/2025-11-16-debugging-the-acer-nitro-5-an515-58-fn-f10-keyboard-backlight-bug-on-linux/#wmi-interface-issues
Tested-by: Bugaddr <Bugaddr@protonmail.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251117155938.3030-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
isst_if_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c.
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning.
Fixes: d3a23584294c ("platform/x86: ISST: Add Intel Speed Select mmio interface")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20251117033354.132-1-vulab@iscas.ac.cn
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add ACPI ID for Nova Lake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20251110235041.123685-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add AWCC support to Alienware 16 Aurora
Cc: stable@vger.kernel.org
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Reviewed-by: Kurt Borja <kuurtb@gmail.com>
Link: https://patch.msgid.link/20251116185311.18074-1-anthony.wong@canonical.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Some devices (such as Smaug) report having MOTION_SENSE_FIFO but do not
support controlling the behaviour of the FIFO interrupt via the
FIFO_INT_ENABLE command and in these cases the interrupt is always
enabled. However, currently the code assumes that if MOTION_SENSE_FIFO
is supported then so is FIFO_INT_ENABLE, and when it tries to enable
the interrupt via this command and an unsupported device reports a
failure it then propagates this into failing the sensors probe.
Interpret the return value -EINVAL as a device where FIFO_INT_ENABLE is
not present and the interrupt is always enabled.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Link: https://lore.kernel.org/r/20251112-diogo-smaug_ec_sensorhub-v1-1-f71d4e9eb9d4@tecnico.ulisboa.pt
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
|
|
New HP Omen laptops follow the same WMI thermal profile as Victus
16-r1000 and 16-s1000.
Add DMI board 8D41 to victus_s_thermal_profile_boards.
Signed-off-by: Marcos Vega <marcosmola2@gmail.com>
Link: https://patch.msgid.link/20251108114739.9255-3-marcosmola2@gmail.com
[ij: changelog taken partially from v1]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add panel_hd_mode to toggle the panel mode between single and high
definition modes.
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251102215319.3126879-4-denis.benato@linux.dev
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The fw_attributes_class provides a much cleaner interface to all of the
attributes introduced to asus-wmi. This patch moves all of these extra
attributes over to fw_attributes_class, and shifts the bulk of these
definitions to a new kernel module to reduce the clutter of asus-wmi
with the intention of deprecating the asus-wmi attributes in future.
The work applies only to WMI methods which don't have a clearly defined
place within the sysfs and as a result ended up lumped together in
/sys/devices/platform/asus-nb-wmi/ with no standard API.
Where possible the fw attrs now implement defaults, min, max, scalar,
choices, etc. As en example dgpu_disable becomes:
/sys/class/firmware-attributes/asus-armoury/attributes/dgpu_disable/
├── current_value
├── display_name
├── possible_values
└── type
as do other attributes.
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://patch.msgid.link/20251102215319.3126879-3-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The WMI driver core only supports GUID strings containing only
uppercase characters, however the GUID string used by the
msi-wmi-platform driver contains a single lowercase character.
This prevents the WMI driver core from matching said driver to
its WMI device.
Fix this by turning the lowercase character into a uppercase
character. Also update the WMI driver development guide to warn
about this.
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Fixes: 9c0beb6b29e7 ("platform/x86: wmi: Add MSI WMI Platform driver")
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251110111253.16204-3-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
It turns out that the GUID used by the msi-wmi-platform driver
(ABBC0F60-8EA1-11D1-00A0-C90629100000) is not unique, but was instead
copied from the WIndows Driver Samples. This means that this driver
could load on devices from other manufacturers that also copied this
GUID, potentially causing hardware errors.
Prevent this by only loading on devices whitelisted via DMI. The DMI
matches where taken from the msi-ec driver.
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Fixes: 9c0beb6b29e7 ("platform/x86: wmi: Add MSI WMI Platform driver")
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251110111253.16204-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Export symbols for reading/writing WMI symbols using a namespace.
Existing functions:
- asus_wmi_evaluate_method
- asus_wmi_set_devstate
New function:
- asus_wmi_get_devstate_dsts
The new function is intended for use with DSTS WMI method only and
avoids requiring the asus_wmi driver data to select the WMI method.
Co-developed-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Denis Benato <denis.benato@linux.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20251102215319.3126879-2-denis.benato@linux.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Drop profile matching micro-optimizations to improve readability and
long-term maintainability.
Additionally, is_awcc_thermal_profile_id is implicitly ignoring the
AWCC_PROFILE_SPECIAL_GMODE ID. State this explicitly with code and a
comment.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://patch.msgid.link/20251103-aw-gmode-v1-1-eba7b7be0a9c@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add a new driver for Uniwill laptops. The driver uses a ACPI
interface to talk with the embedded controller, but relies on a
ACPI WMI interface for receiving event notifications.
The driver is reverse-engineered based on the following information:
- OEM software from intel
- https://github.com/pobrn/qc71_laptop
- https://gitlab.com/tuxedocomputers/development/packages/tuxedo-drivers
- https://github.com/tuxedocomputers/tuxedo-control-center
The underlying EC supports various features, including hwmon sensors,
battery charge limiting, a RGB lightbar and keyboard-related controls.
Reported-by: cyear <chumuzero@gmail.com>
Closes: https://github.com/lm-sensors/lm-sensors/issues/508
Closes: https://github.com/Wer-Wolf/uniwill-laptop/issues/3
Tested-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://patch.msgid.link/20251102172942.17879-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The GBMD/SBMC interface on recent devices supports Rapid Charge mode
(charge_types: Fast) in addition to Conservation Mode (charge_types:
Long_Life).
Query the GBMD interface on probe to determine if a device supports
Rapid Charge. If so, expose these two modes while carefully maintaining
their mutually exclusive state, which aligns with the behavior of
manufacturer utilities on Windows.
Signed-off-by: Rong Zhang <i@rong.moe>
Acked-by: Ike Panhc <ikepanhc@gmail.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-By: Jelle van der Waa <jelle@vdwaa.nl>
Link: https://patch.msgid.link/20251105182832.104946-5-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Some recent devices supports more charge_types. To properly support
these device without breaking the existing ones, we need to define
multiple power_supply_ext for different GBMD/SBMC interface revisions.
No functional change intended.
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20251105182832.104946-4-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The upcoming changes for Rapid Charge support require two consecutive
SBMC calls to switch charge_types. Hence, a mutex is required.
No functional change intended.
Signed-off-by: Rong Zhang <i@rong.moe>
Acked-by: Ike Panhc <ikepanhc@gmail.com>
Link: https://patch.msgid.link/20251105182832.104946-3-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Use the str_on_off() helper instead of open-coding the same operation.
This improves code readability.
No functional change intended.
Suggested-by: kernel test robot <lkp@intel.com>
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/202510311551.xjWbHTrm-lkp@intel.com/
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/2bae2ea7-2ef9-0cfa-0c2c-39a7043b2aa5@linux.intel.com/
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://patch.msgid.link/20251105182832.104946-2-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
After unbinding the driver, another kthread `cros_ec_console_log_work`
is still accessing the device, resulting an UAF and crash.
The driver doesn't unregister the EC device in .remove() which should
shutdown sub-devices synchronously. Fix it.
Fixes: 26a14267aff2 ("platform/chrome: Add ChromeOS EC ISHTP driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20251031033900.3577394-1-tzungbi@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
|
|
Destage the VCHIQ MMAL driver to drivers/platform/raspberrypi.
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Link: https://patch.msgid.link/20251029-vchiq-destage-v3-7-da8d6c83c2c5@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Destage the VCHIQ interface driver to drivers/platform/raspberrypi.
There is still the remaining TODO item of improving the documentation,
which can be handled post destaging.
Secondly, multimedia drivers like codec and ISP that rely on this
interface need to be upstreamed. And lastly, the drivers that facilitate
the shared memory between VideoCore and Linux, like the vc-sm-cma driver
and vc_mem char driver also need to be upstreamed.
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Link: https://patch.msgid.link/20251029-vchiq-destage-v3-6-da8d6c83c2c5@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
