| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 2ba8425678af422da37b6c9b50e9ce66f0f55cae ]
Since the CONFIG_CTL register is only 32 bits wide in the Stromer
and Stromer Plus PLLs , the 'config_ctl_hi_val' values from the
IPQ5018 and IPQ5332 configurations are not used so remove those.
No functional changes.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240509-stromer-config-ctl-v1-1-6034e17b28d5@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 878e845d8db04df9ff3bbbaac09d335b24153704 ]
Commit 2f7b1d8b5505 ("clk: mediatek: Do a runtime PM get on controllers
during probe") enabled runtime PM for all mediatek clock controllers,
but this introduced an issue on the resume path.
If a device resumes earlier than the clock controller and calls
clk_prepare() when runtime PM is enabled on the controller, it will end
up calling clk_pm_runtime_get(). But the subsequent
pm_runtime_resume_and_get() call will fail because the runtime PM is
temporarily disabled during suspend.
To workaround this, introduce a need_runtime_pm flag and only enable it
on mt8183-mfgcfg, which is the driver that observed deadlock previously.
Hopefully mt8183-cfgcfg won't run into the issue at the resume stage
because the GPU should have stopped rendering before the system calls
suspend.
Fixes: 2f7b1d8b5505 ("clk: mediatek: Do a runtime PM get on controllers during probe")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240613120357.1043342-1-treapking@chromium.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a33a64524e6381c399e5e42571d9363ffc0bed4 ]
The clk_alpha_pll_stromer_plus_set_rate() function does not
sets the ALPHA_EN bit in the USER_CTL register, so setting
rates which requires using alpha mode works only if the bit
gets set already prior calling the function.
Extend the function to set the ALPHA_EN bit in order to allow
using fractional rates regardless whether the bit gets set
previously or not.
Fixes: 84da48921a97 ("clk: qcom: clk-alpha-pll: introduce stromer plus ops")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240508-stromer-plus-alpha-en-v1-1-6639ce01ca5b@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3414f41a13eb41db15c558fbc695466203dca4fa ]
Both gpll6 and gpll7 are parented to CXO at 19.2 MHz and not to GPLL0
which runs at 600 MHz. Also gpll6_out_even should have the parent gpll6
and not gpll0.
Adjust the parents of these clocks to make Linux report the correct rate
and not absurd numbers like gpll7 at ~25 GHz or gpll6 at 24 GHz.
Corrected rates are the following:
gpll7 807999902 Hz
gpll6 768000000 Hz
gpll6_out_even 384000000 Hz
gpll0 600000000 Hz
gpll0_out_odd 200000000 Hz
gpll0_out_even 300000000 Hz
And because gpll6 is the parent of gcc_sdcc2_apps_clk_src (at 202 MHz)
that clock also reports the correct rate now and avoids this warning:
[ 5.984062] mmc0: Card appears overclocked; req 202000000 Hz, actual 6312499237 Hz
Fixes: 131abae905df ("clk: qcom: Add SM6350 GCC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240508-sm6350-gpll-fix-v1-1-e4ea34284a6d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ea977d742507e534d9fe4f4d74256f6b7f589338 upstream.
In order to set the rate range of a hw sunxi_ccu_probe calls
hw_to_ccu_common() assuming all entries in desc->ccu_clks are contained
in a ccu_common struct. This assumption is incorrect and, in
consequence, causes invalid pointer de-references.
Remove the faulty call. Instead, add one more loop that iterates over
the ccu_clks and sets the rate range, if required.
Fixes: b914ec33b391 ("clk: sunxi-ng: common: Support minimum and maximum rate")
Reported-by: Robert J. Pafford <pafford.9@buckeyemail.osu.edu>
Closes: https://lore.kernel.org/lkml/DM6PR01MB58047C810DDD5D0AE397CADFF7C22@DM6PR01MB5804.prod.exchangelabs.com/
Cc: stable@vger.kernel.org
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Tested-by: Robert J. Pafford <pafford.9@buckeyemail.osu.edu>
Link: https://lore.kernel.org/r/20240623-sunxi-ng_fix_common_probe-v1-1-7c97e32824a1@oltmanns.dev
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72ceafb587a56e26c905472418c7dc2033c294d3 upstream.
The crypto_ahb and crypto_axi clks are hardware voteable.
This means that the halt bit isn't reliable because some
other voter in the system, e.g. TrustZone, could be keeping
the clk enabled when the kernel turns it off from clk_disable().
Make these clks use voting mode by changing the halt check to
BRANCH_HALT_VOTED and toggle the voting bit in the voting register
instead of directly controlling the branch by writing to the branch
register. This fixes stuck clk warnings seen on ipq9574 and saves
power by actually turning the clk off.
Also changes the CRYPTO_AHB_CLK_ENA & CRYPTO_AXI_CLK_ENA
offset to 0xb004 from 0x16014.
Cc: stable@vger.kernel.org
Fixes: f6b2bd9cb29a ("clk: qcom: gcc-ipq9574: Enable crypto clocks")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://lore.kernel.org/r/20240509105405.1262369-1-quic_mdalam@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2607133196c35f31892ee199ce7ffa717bea4ad1 ]
These clkdevs were unnecessary, because systems using this driver always
look up clocks using the devicetree. And as Russell King points out[1],
since the provided device name was truncated, lookups via clkdev would
never match.
Recently, commit 8d532528ff6a ("clkdev: report over-sized strings when
creating clkdev entries") caused clkdev registration to fail due to the
truncation, and this now prevents the driver from probing. Fix the
driver by removing the clkdev registration.
Link: https://lore.kernel.org/linux-clk/ZkfYqj+OcAxd9O2t@shell.armlinux.org.uk/ [1]
Fixes: 30b8e27e3b58 ("clk: sifive: add a driver for the SiFive FU540 PRCI IP block")
Fixes: 8d532528ff6a ("clkdev: report over-sized strings when creating clkdev entries")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/linux-clk/7eda7621-0dde-4153-89e4-172e4c095d01@roeck-us.net/
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20240528001432.1200403-1-samuel.holland@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5fce38e2a1a97900989d9fedebcf5a4dacdaee30 upstream.
Booting v6.8 results in a hang on various IPQ5018 based boards.
Investigating the problem showed that the hang happens when the
clk_alpha_pll_stromer_plus_set_rate() function tries to write
into the PLL_MODE register of the APSS PLL.
Checking the downstream code revealed that it uses [1] stromer
specific operations for IPQ5018, whereas in the current code
the stromer plus specific operations are used.
The ops in the 'ipq_pll_stromer_plus' clock definition can't be
changed since that is needed for IPQ5332, so add a new alpha pll
clock declaration which uses the correct stromer ops and use this
new clock for IPQ5018 to avoid the boot failure.
Also, change pll_type in 'ipq5018_pll_data' to
CLK_ALPHA_PLL_TYPE_STROMER to better reflect that it is a Stromer
PLL and change the apss_ipq_pll_probe() function accordingly.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c#L67
Cc: stable@vger.kernel.org
Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Tested-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240315-apss-ipq-pll-ipq5018-hang-v2-1-6fe30ada2009@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c5b3e17b8fd1f1add5a9477306c355fab126977 upstream.
The clk_alpha_pll_stromer_set_rate() function writes inproper
values into the ALPHA_VAL{,_U} registers which results in wrong
clock rates when the alpha value is used.
The broken behaviour can be seen on IPQ5018 for example, when
dynamic scaling sets the CPU frequency to 800000 KHz. In this
case the CPU cores are running only at 792031 KHz:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
792031
This happens because the function ignores the fact that the alpha
value calculated by the alpha_pll_round_rate() function is only
32 bits wide which must be extended to 40 bits if it is used on
a hardware which supports 40 bits wide values.
Extend the clk_alpha_pll_stromer_set_rate() function to convert
the alpha value to 40 bits before wrinting that into the registers
in order to ensure that the hardware really uses the requested rate.
After the change the CPU frequency is correct:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
800000
Cc: stable@vger.kernel.org
Fixes: e47a4f55f240 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240328-alpha-pll-fix-stromer-set-rate-v3-1-1b79714c78bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dc445c1905096b2ed4db1a84570375b4e00cc0f upstream.
Commit f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
raspberrypi_discover_clocks() due to ->num being assigned after ->hws
has been accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-raspberrypi.c:374:4
index 3 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-2-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9368cdf90f52a68120d039887ccff74ff33b4444 upstream.
Commit f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
clk_dvp_probe() due to ->num being assigned after ->hws has been
accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-bcm2711-dvp.c:59:2
index 0 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d67 ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-1-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c55f7ee2ec239b6afd8639c7ac06493876deb0ea ]
According to ipq5018.dtsi, the maximum supported rate by the
CPU is 1.008 GHz on the IPQ5018 platform, however the current
configuration of the PLL results in 1.2 GHz rate.
Change the 'L' value in the PLL configuration to limit the
rate to 1.008 GHz. The downstream kernel also uses the same
value [1]. Also add a comment to indicate the desired
frequency.
[1] https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c?ref_type=heads#L151
Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240326-fix-ipq5018-apss-pll-rate-v1-1-82ab31c9da7e@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07fb0a76bb757990b99fc2ab78ad7d1709cc441d ]
CONFIG_SM_GCC_8650 depends on ARM64 but it is selected by
CONFIG_SM_GPUCC_8650, which can be selected on ARM, resulting in a
Kconfig warning.
WARNING: unmet direct dependencies detected for SM_GCC_8650
Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=y] && (ARM64 || COMPILE_TEST [=n])
Selected by [y]:
- SM_GPUCC_8650 [=y] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=y]
Add the same dependencies to CONFIG_SM_GPUCC_8650 to resolve the
warning.
Fixes: 8676fd4f3874 ("clk: qcom: add the SM8650 GPU Clock Controller driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240318-fix-some-qcom-kconfig-deps-v1-2-ea0773e3df5a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e00f2540a581f8b8c165e5ae8afe52e4ad038550 ]
CONFIG_SC_GCC_8280XP depends on ARM64 but it is selected by
CONFIG_SC_CAMCC_8280XP, which can be selected on ARM, resulting in a
Kconfig warning.
WARNING: unmet direct dependencies detected for SC_GCC_8280XP
Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=y] && (ARM64 || COMPILE_TEST [=n])
Selected by [y]:
- SC_CAMCC_8280XP [=y] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=y]
Add the same dependencies to CONFIG_SC_CAMCC_8280XP to resolve the
warning.
Fixes: ff93872a9c61 ("clk: qcom: camcc-sc8280xp: Add sc8280xp CAMCC")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240318-fix-some-qcom-kconfig-deps-v1-1-ea0773e3df5a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e20ae5ae9f0c843aded4f06f3d1cab7384789e92 ]
Right now, msm8998 video decoder (venus) is non-functional:
$ time mpv --hwdec=v4l2m2m-copy --vd-lavc-software-fallback=no --vo=null --no-audio --untimed --length=30 --quiet demo-480.webm
(+) Video --vid=1 (*) (vp9 854x480 29.970fps)
Audio --aid=1 --alang=eng (*) (opus 2ch 48000Hz)
[ffmpeg/video] vp9_v4l2m2m: output VIDIOC_REQBUFS failed: Connection timed out
[ffmpeg/video] vp9_v4l2m2m: no v4l2 output context's buffers
[ffmpeg/video] vp9_v4l2m2m: can't configure decoder
Could not open codec.
Software decoding fallback is disabled.
Exiting... (Quit)
Bryan O'Donoghue suggested the proper fix:
- Set required register offsets in venus GDSC structs.
- Set HW_CTRL flag.
$ time mpv --hwdec=v4l2m2m-copy --vd-lavc-software-fallback=no --vo=null --no-audio --untimed --length=30 --quiet demo-480.webm
(+) Video --vid=1 (*) (vp9 854x480 29.970fps)
Audio --aid=1 --alang=eng (*) (opus 2ch 48000Hz)
[ffmpeg/video] vp9_v4l2m2m: VIDIOC_G_FMT ioctl
[ffmpeg/video] vp9_v4l2m2m: VIDIOC_G_FMT ioctl
...
Using hardware decoding (v4l2m2m-copy).
VO: [null] 854x480 nv12
Exiting... (End of file)
real 0m3.315s
user 0m1.277s
sys 0m0.453s
NOTES:
GDSC = Globally Distributed Switch Controller
Use same code as mmcc-msm8996 with:
s/venus_gdsc/video_top_gdsc/
s/venus_core0_gdsc/video_subcore0_gdsc/
s/venus_core1_gdsc/video_subcore1_gdsc/
https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/caf_migration/kernel.lnx.4.4.r38-rel/include/dt-bindings/clock/msm-clocks-hwio-8996.h
https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/caf_migration/kernel.lnx.4.4.r38-rel/include/dt-bindings/clock/msm-clocks-hwio-8998.h
0x1024 = MMSS_VIDEO GDSCR (undocumented)
0x1028 = MMSS_VIDEO_CORE_CBCR
0x1030 = MMSS_VIDEO_AHB_CBCR
0x1034 = MMSS_VIDEO_AXI_CBCR
0x1038 = MMSS_VIDEO_MAXI_CBCR
0x1040 = MMSS_VIDEO_SUBCORE0 GDSCR (undocumented)
0x1044 = MMSS_VIDEO_SUBCORE1 GDSCR (undocumented)
0x1048 = MMSS_VIDEO_SUBCORE0_CBCR
0x104c = MMSS_VIDEO_SUBCORE1_CBCR
Fixes: d14b15b5931c2b ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/ff4e2e34-a677-4c39-8c29-83655c5512ae@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 615a292ee4d51303246278f3fa33cc38700fe00e ]
On SM8650 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display af54000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 9e939f008338 ("clk: qcom: add the SM8650 Display Clock Controller driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-4-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e90b5139da8465a15c3820b4b67ca9468dce93b4 ]
On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 90114ca11476 ("clk: qcom: add SM8550 DISPCC driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-3-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1113501cfb46d5c0eb960f0a8a9f6c0f91dc6fb6 ]
On SM6350 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 837519775f1d ("clk: qcom: Add display clock controller driver for SM6350")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-2-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e801038a02ce1e8c652a0b668dd233a4ee48aeb7 ]
On SM8450 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 16fb89f92ec4 ("clk: qcom: Add support for Display Clock Controller on SM8450")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-1-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44019387fce230beda35b83da3a2c9fc5787704e ]
Add the missing clock and reset entry for PLIC. Also add
R9A07G043_NCEPLIC_ACLK to the critical clocks list.
Fixes: 95d48d270305ad2c ("clk: renesas: r9a07g043: Add support for RZ/Five SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240403200952.633084-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3b23118bdbd898dc2f4de8f549d598d492c42ba8 ]
According to Figure 52A.1 ("RS-CANFD Module Block Diagram (in classical
CAN mode)") in the R-Car V3U Series User’s Manual Rev. 0.5, the parent
clock for the CANFD peripheral module clock is the S3D2 clock.
Fixes: 9b621b6adff53346 ("clk: renesas: r8a779a0: Add CANFD module clock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/aef9300f44c9141b1465343f91c5cc7303249b6e.1713279523.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7cf0324ba0bc61a8c360d23d284e06d2994b1fef ]
When SPI transfer is being prepared, the spi-s3c64xx driver will call
clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK
is a gate (leaf) clock, so it must propagate the rate change up the
clock tree, so that corresponding MUX/DIV clocks can actually change
their values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for
all USI instances in GS101 PERIC1: USI{0, 9, 10, 11, 12, 13}. This change
involves the following clocks:
PERIC1 USI*:
Clock Div range MUX Selection
-------------------------------------------------------------------
gout_peric1_peric1_top0_ipclk_* - -
dout_peric1_usi*_usi /1..16 -
mout_peric1_usi*_usi_user - {24.5 MHz, 400 MHz}
With input clock of 400 MHz this scheme provides the following IPCLK
rate range, for each USI block:
PERIC1 USI*: 1.5 MHz ... 400 MHz
Accounting for internal /4 divider in SPI blocks, and because the max
SPI frequency is limited at 50 MHz, it gives us next SPI SCK rates:
PERIC1 USI_SPI*: 384 KHz ... 49.9 MHz
Which shall be fine for the applications of the SPI bus.
Note that with this we allow the reparenting of the MUX_USIx clocks to
OSCCLK. Each instance of the USI IP has its own MUX_USI clock, thus the
reparenting of a MUX_USI clock corresponds to a single instance of the
USI IP. The datasheet mentions OSCCLK just in the low-power mode
context, but the downstream driver reparents too the MUX_USI clocks to
OSCCLK. Follow the downstream driver and do the same.
Fixes: 2999e786d7e9 ("clk: samsung: gs101: add support for cmu_peric1")
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240419100915.2168573-3-tudor.ambarus@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7b54d9113cd4923432c0b2441c5e2663873b4e5b ]
Introduce nMUX() for MUX clocks that can be reparented on clock rate
change. "nMUX" comes from "n-to-1 selector", hopefully emphasising that
the selector can change on clock rate changes. Ideally MUX/MUX_F()
should change to not have the CLK_SET_RATE_NO_REPARENT flag set by
default, and all their users to be updated to add the flag back
(like in the case of DIV and GATE). But this is a very intrusive change
and because for now only GS101 allows MUX reparenting on clock rate
change, stick with nMUX().
GS101 defines MUX clocks that are dedicated for each instance of the IP.
One example is USI IP (SPI, I2C, serial). The reparenting of these MUX
clocks will not affect other instances of the same IP or different IPs
altogether.
When SPI transfer is being prepared, the spi-s3c64xx driver will call
clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK
is a gate (leaf) clock, so it must propagate the rate change up the
clock tree, so that corresponding MUX/DIV clocks can actually change
their values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for
all USI instances in GS101 PERIC0: USI{1-8, 14}. This change involves the
following clocks:
PERIC0 USI*:
Clock Div range MUX Selection
-------------------------------------------------------------------
gout_peric0_peric0_top0_ipclk_* - -
dout_peric0_usi*_usi /1..16 -
mout_peric0_usi*_usi_user - {24.5 MHz, 400 MHz}
With input clock of 400 MHz this scheme provides the following IPCLK
rate range, for each USI block:
PERIC0 USI*: 1.5 MHz ... 400 MHz
Accounting for internal /4 divider in SPI blocks, and because the max
SPI frequency is limited at 50 MHz, it gives us next SPI SCK rates:
PERIC0 USI_SPI*: 384 KHz ... 49.9 MHz
Fixes: 893f133a040b ("clk: samsung: gs101: add support for cmu_peric0")
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240419100915.2168573-2-tudor.ambarus@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f2bc4acbb1916b8cd2ce4bb3ba7b1cd7cb705fa ]
The offset of the CONFIG_CTL_U register defined for the Stromer
PLL is wrong. It is not aligned on a 4 bytes boundary which might
causes errors in regmap operations.
Maybe the intention behind of using the 0xff value was to indicate
that the register is not implemented in the PLL, but this is not
verified anywhere in the code. Moreover, this value is not used
even in other register offset arrays despite that those PLLs also
have unimplemented registers.
Additionally, on the Stromer PLLs the current code only touches
the CONFIG_CTL_U register if the result of pll_has_64bit_config()
is true which condition is not affected by the change.
Due to the reasons above, simply remove the CONFIG_CTL_U entry
from the Stromer specific array.
Fixes: e47a4f55f240 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-1-f7c0c5607cca@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1758c68c81b8b881818fcebaaeb91055362a82f8 ]
According to 9FGV0241, 9FGV0441 & 9FGV0841 datasheets, the default
value for the clock amplitude is 0.8V, while the driver assumes 0.7V.
Additionally, define constants for default values for both clock
amplitude and spread spectrum and use them.
Fixes: 892e0ddea1aa ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240415140348.2887619-1-catalin.popescu@leica-geosystems.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4c0c087772d7e29bc2489ddb068d5167140bfc38 ]
To have a working display through DPI, a workaround has been
implemented downstream to add "mm_dpi0_dpi0" and "dpi0_sel" to
the DPI node. Shortly, that add an extra clock.
It seems consistent to have the "dpi0_sel" as parent.
Additionnaly, "vpll_dpix" isn't used/managed.
Then, set the "mm_dpi0_dpi0" parent clock to "dpi0_sel".
The new clock tree is:
clk26m
lvdspll
lvdspll_X (2, 4, 8, 16)
dpi0_sel
mm_dpi0_dpi0
Fixes: d46adccb7966 ("clk: mediatek: add driver for MT8365 SoC")
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231023-display-support-v3-12-53388f3ed34b@baylibre.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb7b3c8e7180f36de75cdea200ab7127f93f58cc ]
Support for fhctl clocks in apmixedsys was introduced at a later point
and to this moment only one mt6795 based platform has a fhctl DT node
present. Therefore the fhctl support in apmixedsys should be seen as
optional and not cause an error when it is missing.
Change the message's log level to warning. The warning level is chosen
so that it will still alert the fact that fhctl support might be
unintentionally missing, but without implying that this is necessarily
an issue.
Even if the FHCTL DT nodes are added to all current platforms moving
forward, since those changes won't be backported, this ensures stable
kernel releases won't have live with this error.
Fixes: d7964de8a8ea ("clk: mediatek: Add new clock driver to handle FHCTL hardware")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20240308-mtk-fhctl-no-node-error-v1-1-51e446eb149a@collabora.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04ee3a0b44e3d18cf6b0c712d14b98624877fd26 ]
All PLL id values of CMU_TOP were incorrectly set to FOUT_SHARED0_PLL.
It modified to the correct PLL clock id value.
Fixes: 6587c62f69dc ("clk: samsung: add top clock support for Exynos Auto v9 SoC")
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240328091000.17660-1-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
device_get_match_data() function should not be used on the device other
than the one matched to the given driver, because it always returns the
match_data of the matched driver. In case of exynos-clkout driver, the
original code matches the OF IDs on the PARENT device, so replacing it
with of_device_get_match_data() broke the driver.
This has been already pointed once in commit 2bc5febd05ab ("clk: samsung:
Revert "clk: samsung: exynos-clkout: Use of_device_get_match_data()"").
To avoid further confusion, add a comment about this special case, which
requires direct of_match_device() call to pass custom IDs array.
This partially reverts commit 409c39ec92a35e3708f5b5798c78eae78512cd71.
Cc: <stable@vger.kernel.org>
Fixes: 409c39ec92a3 ("clk: Use device_get_match_data()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20240425075628.838497-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240430184656.357805-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk driver fixes from Jernej Skrabec:
- fix H6 CPU rate change via reparenting
- set A64 MIPI PLL min & max rate
* tag 'sunxi-clk-fixes-for-6.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a64: Set minimum and maximum rate for PLL-MIPI
clk: sunxi-ng: common: Support minimum and maximum rate
clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into clk-fixes
Pull Qualcomm clk driver fixes from Bjorn Andersson:
The introduction of support for the external VDD_GFX supply in SA8295P
ADP unearthed a lockdep problem in the GDSC code w.r.t regulator
supplies. Make the regulator optional, to avoid creating a dummy
regulator, on those boards that doesn't use this. While not solving the
root cause of the problem, it reduces the impact of the lockdep warning
- and it avoids wasting resources.
Refactoring of the RPM clock driver accidentally removed num_clks from
msm8976. Reintroduce this to get the clocks back.
* tag 'qcom-clk-fixes-for-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
clk: qcom: smd-rpm: Restore msm8976 num_clk
clk: qcom: gdsc: treat optional supplies as optional
|
|
When the Allwinner A64's TCON0 searches the ideal rate for the connected
panel, it may happen that it requests a rate from its parent PLL-MIPI
which PLL-MIPI does not support.
This happens for example on the Olimex TERES-I laptop where TCON0
requests PLL-MIPI to change to a rate of several GHz which causes the
panel to stay blank. It also happens on the pinephone where a rate of
less than 500 MHz is requested which causes instabilities on some
phones.
Set the minimum and maximum rate of Allwinner A64's PLL-MIPI according
to the Allwinner User Manual.
Fixes: ca1170b69968 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reported-by: Diego Roversi <diegor@tiscali.it>
Closes: https://groups.google.com/g/linux-sunxi/c/Rh-Uqqa66bw
Tested-by: Diego Roversi <diegor@tiscali.it>
Cc: stable@vger.kernel.org
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-2-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The Allwinner SoC's typically have an upper and lower limit for their
clocks' rates. Up until now, support for that has been implemented
separately for each clock type.
Implement that functionality in the sunxi-ng's common part making use of
the CCF rate liming capabilities, so that it is available for all clock
types.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Cc: stable@vger.kernel.org
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-1-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
While PLL CPUX clock rate change when CPU is running from it works in
vast majority of cases, now and then it causes instability. This leads
to system crashes and other undefined behaviour. After a lot of testing
(30+ hours) while also doing a lot of frequency switches, we can't
observe any instability issues anymore when doing reparenting to stable
clock like 24 MHz oscillator.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Reported-by: Chad Wagner <wagnerch42@gmail.com>
Link: https://forum.libreelec.tv/thread/27295-orange-pi-3-lts-freezes/
Tested-by: Chad Wagner <wagnerch42@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20231013181712.2128037-1-jernej.skrabec@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Due to what seems to be an undocumented oddity in MediaTek's MT7988
SoC design the CLK_INFRA_PCIE_PERI_26M_CK_P2 clock requires
CLK_INFRA_PCIE_PERI_26M_CK_P3 to be enabled.
This currently leads to PCIe port 2 not working in Linux.
Reflect the apparent relationship in the clk driver to make sure PCIe
port 2 of the MT7988 SoC works.
Fixes: 4b4719437d85f ("clk: mediatek: add drivers for MT7988 SoC")
Suggested-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/1da2506a51f970706bf4ec9509dd04e0471065e5.1710367453.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
mt8183-mfgcfg has a mutual dependency with genpd during the probing
stage, which leads to a deadlock in the following call stack:
CPU0: genpd_lock --> clk_prepare_lock
genpd_power_off_work_fn()
genpd_lock()
generic_pm_domain::power_off()
clk_unprepare()
clk_prepare_lock()
CPU1: clk_prepare_lock --> genpd_lock
clk_register()
__clk_core_init()
clk_prepare_lock()
clk_pm_runtime_get()
genpd_lock()
Do a runtime PM get at the probe function to make sure clk_register()
won't acquire the genpd lock. Instead of only modifying mt8183-mfgcfg,
do this on all mediatek clock controller probings because we don't
believe this would cause any regression.
Verified on MT8183 and MT8192 Chromebooks.
Fixes: acddfc2c261b ("clk: mediatek: Add MT8183 clock support")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240312115249.3341654-1-treapking@chromium.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Similar to the previous commit, we should make sure that all devices are
runtime resumed before printing the clk_summary through debugfs. Failure
to do so would result in a deadlock if the thread is resuming a device
to print clk state and that device is also runtime resuming in another
thread, e.g the screen is turning on and the display driver is starting
up. We remove the calls to clk_pm_runtime_{get,put}() in this path
because they're superfluous now that we know the devices are runtime
resumed. This also squashes a bug where the return value of
clk_pm_runtime_get() wasn't checked, leading to an RPM count underflow
on error paths.
Fixes: 1bb294a7981c ("clk: Enable/Disable runtime PM for clk_summary")
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-6-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Doug reported [1] the following hung task:
INFO: task swapper/0:1 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
rpm_resume+0xe0/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
clk_pm_runtime_get+0x30/0xb0
clk_disable_unused_subtree+0x58/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused+0x4c/0xe4
do_one_initcall+0xcc/0x2d8
do_initcall_level+0xa4/0x148
do_initcalls+0x5c/0x9c
do_basic_setup+0x24/0x30
kernel_init_freeable+0xec/0x164
kernel_init+0x28/0x120
ret_from_fork+0x10/0x20
INFO: task kworker/u16:0:9 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008
Workqueue: events_unbound deferred_probe_work_func
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
schedule_preempt_disabled+0x2c/0x48
__mutex_lock+0x238/0x488
__mutex_lock_slowpath+0x1c/0x28
mutex_lock+0x50/0x74
clk_prepare_lock+0x7c/0x9c
clk_core_prepare_lock+0x20/0x44
clk_prepare+0x24/0x30
clk_bulk_prepare+0x40/0xb0
mdss_runtime_resume+0x54/0x1c8
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x68/0x7c
genpd_runtime_resume+0x108/0x1f4
__rpm_callback+0x84/0x144
rpm_callback+0x30/0x88
rpm_resume+0x1f4/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
device_add+0x644/0x814
mipi_dsi_device_register_full+0xe4/0x170
devm_mipi_dsi_device_register_full+0x28/0x70
ti_sn_bridge_probe+0x1dc/0x2c0
auxiliary_bus_probe+0x4c/0x94
really_probe+0xcc/0x2c8
__driver_probe_device+0xa8/0x130
driver_probe_device+0x48/0x110
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x8c/0xd8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
deferred_probe_work_func+0x9c/0xd8
process_one_work+0x148/0x518
worker_thread+0x138/0x350
kthread+0x138/0x1e0
ret_from_fork+0x10/0x20
The first thread is walking the clk tree and calling
clk_pm_runtime_get() to power on devices required to read the clk
hardware via struct clk_ops::is_enabled(). This thread holds the clk
prepare_lock, and is trying to runtime PM resume a device, when it finds
that the device is in the process of resuming so the thread schedule()s
away waiting for the device to finish resuming before continuing. The
second thread is runtime PM resuming the same device, but the runtime
resume callback is calling clk_prepare(), trying to grab the
prepare_lock waiting on the first thread.
This is a classic ABBA deadlock. To properly fix the deadlock, we must
never runtime PM resume or suspend a device with the clk prepare_lock
held. Actually doing that is near impossible today because the global
prepare_lock would have to be dropped in the middle of the tree, the
device runtime PM resumed/suspended, and then the prepare_lock grabbed
again to ensure consistency of the clk tree topology. If anything
changes with the clk tree in the meantime, we've lost and will need to
start the operation all over again.
Luckily, most of the time we're simply incrementing or decrementing the
runtime PM count on an active device, so we don't have the chance to
schedule away with the prepare_lock held. Let's fix this immediate
problem that can be triggered more easily by simply booting on Qualcomm
sc7180.
Introduce a list of clk_core structures that have been registered, or
are in the process of being registered, that require runtime PM to
operate. Iterate this list and call clk_pm_runtime_get() on each of them
without holding the prepare_lock during clk_disable_unused(). This way
we can be certain that the runtime PM state of the devices will be
active and resumed so we can't schedule away while walking the clk tree
with the prepare_lock held. Similarly, call clk_pm_runtime_put() without
the prepare_lock held to properly drop the runtime PM reference. We
remove the calls to clk_pm_runtime_{get,put}() in this path because
they're superfluous now that we know the devices are runtime resumed.
Reported-by: Douglas Anderson <dianders@chromium.org>
Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1]
Closes: https://issuetracker.google.com/328070191
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9a34b45397e5 ("clk: Add support for runtime PM")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Initialize this kref once we allocate memory for the struct clk_core so
that we can reuse the release function to free any memory associated
with the structure. This mostly consolidates code, but also clarifies
that the kref lifetime exists once the container structure (struct
clk_core) is allocated instead of leaving it in a half-baked state for
most of __clk_core_init().
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-4-sboyd@kernel.org
|
|
We don't need to hold the prepare_lock when dropping a ref on a struct
clk_core. The release function is only freeing memory and any code with
a pointer reference has already unlinked anything pointing to the
clk_core. This reduces the holding area of the prepare_lock a bit.
Note that we also don't call free_clk() with the prepare_lock held.
There isn't any reason to do that.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-3-sboyd@kernel.org
|
|
Removing this assertion lets us move the kref_put() call outside the
prepare_lock section. We don't need to hold the prepare_lock here to
free memory and destroy the clk_core structure. We've already unlinked
the clk from the clk tree and by the time the release function runs
nothing holds a reference to the clk_core anymore so anything with the
pointer can't access the memory that's being freed anyway. Way back in
commit 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of
prepare_lock") we didn't need to have this assertion either.
Fixes: 496eadf821c2 ("clk: Use lockdep asserts to find missing hold of prepare_lock")
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-2-sboyd@kernel.org
|
|
During rework somehow msm8976 num_clk got removed, restore it.
Fixes: d6edc31f3a68 ("clk: qcom: smd-rpm: Separate out interconnect bus clocks")
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240401171641.8979-1-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Since commit deebc79b28d6 ("clk: qcom: gpucc-sc8280xp: Add external
supply for GX gdsc") the GDSC supply must be treated as optional to
avoid warnings like:
gpu_cc-sc8280xp 3d90000.clock-controller: supply vdd-gfx not found, using dummy regulator
on SC8280XP.
Fortunately, the driver is already prepared to handle this by checking
that the regulator pointer is non-NULL before use.
This also avoids triggering a potential deadlock on SC8280XP even if the
underlying issue still remains for the derivative platforms like SA8295P
that actually use the supply.
Fixes: deebc79b28d6 ("clk: qcom: gpucc-sc8280xp: Add external supply for GX gdsc")
Link: https://lore.kernel.org/lkml/Zf25Sv2x9WaCFuIH@hovoldconsulting.com/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240325085835.26158-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing"
* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: fsl: dpio: fix kcalloc() argument order
bus: ts-nbus: Improve error reporting
bus: ts-nbus: Convert to atomic pwm API
riscv: dts: starfive: jh7110: Add camera subsystem nodes
ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
clk: ti: Improve clksel clock bit parsing for reg property
clk: ti: Handle possible address in the node name
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
reset: Instantiate reset GPIO controller for shared reset-gpios
reset: gpio: Add GPIO-based reset controller
cpufreq: do not open-code of_phandle_args_equal()
of: Add of_phandle_args_equal() helper
reset: simple: add support for Sophgo SG2042
dt-bindings: reset: sophgo: support SG2042
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
ARM: brcmstb: Add debug UART entry for 74165
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Not a ton of stuff happening in the clk framework. We got some more
devm helpers and we seem to be going in the direction of "just turn
this stuff on already and leave me alone!" with the addition of a
devm_clk_bulk_get_all_enable() API. I'm hoping that we can make that
into a pmdomain that drivers attach instead, but this API should help
drivers simplify in the meantime.
Outside of the devm wrappers, we've got the usual clk driver updates
that are dominated by the major phone SoC vendors (Samsung and
Qualcomm) and the non-critical driver fixes for things like incorrect
topology descriptions and wrong registers or bit fields. More details
are below, but I'd say that it looks pretty ordinary. The only thing
that really jumps out at me is the Renesas clk driver that's ignoring
clks that are assigned to remote processors in DeviceTree. That's a
new feature that they're using to avoid marking clks as
CLK_IGNORE_UNUSED based on the configuration of the system.
Core:
- Increase dev_id len for clkdev lookups
- Add a devm_clk_bulk_get_all_enable() API to get and enable all clks
for a device
- Add a devm variant of clk_rate_exclusive_get()
New Drivers:
- Display, TCSR, GPU, and Camera clock controllers for Qualcomm's X1
Elite SoC
- Google GS101 PERIC0 and PERIC1 clock controllers
- Exynos850 PDMA clocks
- Exynos850 CPU cluster 0 and 1 (CMU_CPUCLK0/CMU_CPUCLK1) clock
controllers
Removed Drivers:
- Remove the unused Qualcomm sc7180 modem clk driver
Updates:
- Fix some static checker errors in the Hisilicon clk driver
- Polarfire MSSPLL hardware has 4 output clocks (the driver supported
previously only one output); each of these 4 outputs feed dividers
and the output of each divider feed individual hardware blocks
(e.g. CAN, Crypto, eMMC); individual hardware block drivers need to
control their clocks thus clock driver support was added for all
MSSPLL output clocks
- Typo fixes in the Qualcomm IPQ5018 GCC driver
- Add "qdss_at" clk on Qualcomm IPQ6018, needed for WiFi
- Properly terminate frequency tables in different Qualcomm clk
drivers
- Add MDSS, crypto, and SDCC resets on Qualcomm MSM8953
- Add missing UFS CLKREF clks on Qualcomm SC8180X
- Avoid significant delays during boot by adding a softdep on rpmhpd
to Qualcomm SDM845 gcc driver
- Add QUPv3 RCGS w/ DFS and video resets to Qualcomm SM8150 GCC
driver
- Fix the custom GPU GX "do-nothing" method in the Qualcomm GDSC
driver
- Add an external regulator to GX GDSC on Qualcomm SC8280XP GPU clk
driver
- Switch display, GPU, video, and camera Qualcomm clk drivers to
module_platform_driver()
- Set a longer delay for Venus resets on many Qualcomm SoCs
- Correct the GDSC wait times in the Qualcomm SDM845 display clk
driver
- Fix clock listing Oops on Amlogic axg
- New pll-rate for Rockchip rk3568
- i2s rate improvements for Rockchip rk3399
- Rockchip rk3588 syscon clock fixes and removal of overall
clock-number from the rk3588 binding header
- A prerequisite for later improvements to the Rockchip rk3588 linked
clocks
- Minor clean-ups and error handling improvements in both
composite-8m and SCU i.MX clock drivers
- Fix for SAI_MCLK_SEL definition for i.MX8MP
- Register the Samsung CMU MISC clock controller earlier, so the
Multi Core Timer clocksource can use it on Google GS101
- Propagate Exynos850 SPI IPCLK rate change to parents, so the SPI
will get proper clock rates
- Refactor the generic Samsung CPU clock controllers code, preparing
it for supporting Exynos850 CPU clocks
- Fix some clk kerneldoc warnings
- Add Ethernet, SDHI, DMA, and HyperFLASH/QSPI (RPC-IF) clocks on
Renesas R-Car V4M
- Ignore all clocks which are assigned to a non-Linux system in the
Renesas clk driver
- Add watchdog clock on Renesas RZ/G3S
- Add camera (CRU) clock and reset on Renesas RZ/G2UL
- Add support for the Renesas R-Car V4M (R8A779H0) SoC
- Convert some clk bindings to YAML so they can be validated"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
clk: fractional-divider: Use bit operations consistently
clk: fractional-divider: Move mask calculations out of lock
clk: Fix clk_core_get NULL dereference
clk: starfive: jh7110-vout: Convert to platform remove callback returning void
clk: starfive: jh7110-isp: Convert to platform remove callback returning void
clk: imx: imx8-acm: Convert to platform remove callback returning void
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: mediatek: clk-mt8173-apmixedsys: Use common error handling code in clk_mt8173_apmixed_probe()
clk: Add a devm variant of clk_rate_exclusive_get()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Ilpo Järvinen:
- New acer-wmi HW support
- Support for new revision of amd/pmf heartbeat notify
- Correctly handle asus-wmi HW without LEDs
- fujitsu-laptop battery charge control support
- Support for new hp-wmi thermal profiles
- Support ideapad-laptop refresh rate key
- Put intel/pmc AI accelerator (GNA) into D3 if it has no driver to
allow entry into low-power modes, and temporarily removed Lunar Lake
SSRAM support due to breaking FW changes causing probe fail (further
breaking FW changes are still pending)
- Report pmc/punit_atom devices that prevent reacing low power levels
- Surface Fan speed function support
- Support for more sperial keys and complete the list of models with
non-standard fan registers in thinkpad_acpi
- New DMI touchscreen HW support
- Continued modernization efforts of wmi
- Removal of obsoleted ledtrig-audio call and the related dependency
- Debug & metrics interface improvements
- Miscellaneous cleanups / fixes / improvements
* tag 'platform-drivers-x86-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (87 commits)
platform/x86/intel/pmc: Improve PKGC residency counters debug
platform/x86: asus-wmi: Consider device is absent when the read is ~0
Documentation/x86/amd/hsmp: Updating urls
platform/mellanox: mlxreg-hotplug: Remove redundant NULL-check
platform/x86/amd/pmf: Update sps power thermals according to the platform-profiles
platform/x86/amd/pmf: Add support to get sps default APTS index values
platform/x86/amd/pmf: Add support to get APTS index numbers for static slider
platform/x86/amd/pmf: Add support to notify sbios heart beat event
platform/x86/amd/pmf: Add support to get sbios requests in PMF driver
platform/x86/amd/pmf: Disable debugfs support for querying power thermals
platform/x86/amd/pmf: Differentiate PMF ACPI versions
x86/platform/atom: Check state of Punit managed devices on s2idle
platform/x86: pmc_atom: Check state of PMC clocks on s2idle
platform/x86: pmc_atom: Check state of PMC managed devices on s2idle
platform/x86: pmc_atom: Annotate d3_sts register bit defines
clk: x86: Move clk-pmc-atom register defines to include/linux/platform_data/x86/pmc_atom.h
platform/x86: make fw_attr_class constant
platform/x86/intel/tpmi: Change vsec offset to u64
platform/x86: intel_scu_pcidrv: Remove unused intel-mid.h
platform/x86: intel_scu_wdt: Remove unused intel-mid.h
...
|
|
'clk-rate-exclusive' into clk-next
- Increase dev_id len for clkdev lookups
* clk-samsung: (25 commits)
clk: samsung: Add CPU clock support for Exynos850
clk: samsung: Pass mask to wait_until_mux_stable()
clk: samsung: Keep register offsets in chip specific structure
clk: samsung: Keep CPU clock chip specific data in a dedicated struct
clk: samsung: Pass register layout type explicitly to CLK_CPU()
clk: samsung: Pass actual CPU clock registers base to CPU_CLK()
clk: samsung: Group CPU clock functions by chip
clk: samsung: Use single CPU clock notifier callback for all chips
clk: samsung: Reduce params count in exynos_register_cpu_clock()
clk: samsung: Pull struct exynos_cpuclk into clk-cpu.c
clk: samsung: Improve clk-cpu.c style
dt-bindings: clock: exynos850: Add CMU_CPUCLK0 and CMU_CPUCL1
clk: samsung: gs101: add support for cmu_peric1
clk: samsung: gs101: drop extra empty line
dt-bindings: clock: google,gs101-clock: add PERIC1 clock management unit
clk: samsung: exynos850: Propagate SPI IPCLK rate change
clk: samsung: gs101: gpio_peric0_pclk needs to be kept on
clk: samsung: exynos850: Add PDMA clocks
dt-bindings: clock: tesla,fsd: Fix spelling mistake
clk: samsung: gs101: add support for cmu_peric0
...
* clk-imx:
clk: imx: imx8mp: Fix SAI_MCLK_SEL definition
clk: imx: scu: Use common error handling code in imx_clk_scu_alloc_dev()
clk: imx: composite-8m: Delete two unnecessary initialisations in __imx8m_clk_hw_composite()
clk: imx: composite-8m: Less function calls in __imx8m_clk_hw_composite() after error detection
* clk-rockchip:
clk: rockchip: rk3399: Allow to set rate of clk_i2s0_frac's parent
clk: rockchip: rk3588: use linked clock ID for GATE_LINK
clk: rockchip: rk3588: fix indent
clk: rockchip: rk3588: fix pclk_vo0grf and pclk_vo1grf
dt-bindings: clock: rk3588: add missing PCLK_VO1GRF
dt-bindings: clock: rk3588: drop CLK_NR_CLKS
clk: rockchip: rk3588: fix CLK_NR_CLKS usage
clk: rockchip: rk3568: Add PLL rate for 128MHz
* clk-clkdev:
clkdev: Update clkdev id usage to allow for longer names
* clk-rate-exclusive:
clk: Add a devm variant of clk_rate_exclusive_get()
|
|
'clk-microchip' into clk-next
* clk-remove:
clk: starfive: jh7110-vout: Convert to platform remove callback returning void
clk: starfive: jh7110-isp: Convert to platform remove callback returning void
clk: imx: imx8-acm: Convert to platform remove callback returning void
* clk-amlogic:
clk: meson: Add missing clocks to axg_clk_regmaps
* clk-qcom: (62 commits)
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: qcom: dispcc-sdm845: Adjust internal GDSC wait times
dt-bindings: clk: qcom: drop the SC7180 Modem subsystem clock controller
clk: qcom: drop the SC7180 Modem subsystem clock driver
clk: qcom: Use qcom_branch_set_clk_en()
clk: qcom: branch: Add a helper for setting the enable bit
clk: qcom: dispcc-sm8250: Make clk_init_data and pll_vco const
clk: qcom: gcc-sc8180x: Add missing UFS QREF clocks
clk: qcom: gcc-msm8953: add more resets
clk: qcom: videocc-*: switch to module_platform_driver
...
* clk-parent:
clk: Fix clk_core_get NULL dereference
* clk-microchip:
clk: microchip: mpfs: convert MSSPLL outputs to clk_divider
clk: microchip: mpfs: add missing MSSPLL outputs
clk: microchip: mpfs: setup for using other mss pll outputs
clk: microchip: mpfs: split MSSPLL in two
dt-bindings: can: mpfs: add missing required clock
dt-bindings: clock: mpfs: add more MSSPLL output definitions
|
|
'clk-allwinner' into clk-next
* clk-aspeed:
clk: ast2600: Add FSI parent clock with correct rate
dt-bindings: clock: ast2600: Add FSI clock
* clk-keystone:
clk: keystone: sci-clk: Adding support for non contiguous clocks
* clk-mobileye:
dt-bindings: reset: mobileye,eyeq5-reset: add bindings
dt-bindings: clock: mobileye,eyeq5-clk: add bindings
clk: fixed-factor: add fwname-based constructor functions
clk: fixed-factor: add optional accuracy support
* clk-allwinner:
clk: sunxi: usb: fix kernel-doc warnings
clk: sunxi: sun9i-cpus: fix kernel-doc warnings
clk: sunxi: a20-gmac: fix kernel-doc warnings
|
|
and 'clk-bulk' into clk-next
- Add a devm_clk_bulk_get_all_enable() API to get and enable all clks
for a device
- Fix some static checker errors in the hisilicon clk driver
* clk-renesas: (25 commits)
clk: renesas: r8a779h0: Add RPC-IF clock
clk: renesas: r8a779h0: Add SYS-DMAC clocks
clk: renesas: r8a779h0: Add SDHI clock
clk: renesas: r8a779h0: Add EtherAVB clocks
clk: renesas: r9a07g04[34]: Fix typo for sel_shdi variable
clk: renesas: r9a07g04[34]: Use SEL_SDHI1_STS status configuration for SD1 mux
clk: renesas: r8a779f0: Correct PFC/GPIO parent clock
clk: renesas: r8a779g0: Correct PFC/GPIO parent clocks
clk: renesas: r8a779h0: Add I2C clocks
clk: renesas: r8a779h0: Add watchdog clock
clk: renesas: r8a779h0: Add PFC/GPIO clocks
clk: renesas: r8a779g0: Fix PCIe clock name
clk: renesas: cpg-mssr: Add support for R-Car V4M
clk: renesas: rcar-gen4: Add support for FRQCRC1
clk: renesas: r9a07g043: Add clock and reset entries for CRU
clk: renesas: r9a08g045: Add clock and reset support for watchdog
dt-bindings: clock: Add R8A779H0 V4M CPG Core Clock Definitions
dt-bindings: clock: renesas,cpg-mssr: Document R-Car V4M support
dt-bindings: power: Add r8a779h0 SYSC power domain definitions
dt-bindings: power: renesas,rcar-sysc: Document R-Car V4M support
...
* clk-cleanup:
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
clk: fractional-divider: Use bit operations consistently
clk: fractional-divider: Move mask calculations out of lock
clk: ti: dpll3xxx: use correct function names in kernel-doc
clk: clocking-wizard: Remove redundant initialization of pointer div_addr
clk: keystone: sci-clk: match func name comment to actual
clk: cdce925: Remove redundant assignment to variable 'rate'
MAINTAINERS: drop Sekhar Nori
* clk-hisilicon:
clk: hisilicon: Use devm_kcalloc() instead of devm_kzalloc()
clk: hisilicon: hi3559a: Fix an erroneous devm_kfree()
clk: hisilicon: hi3519: Release the correct number of gates in hi3519_clk_unregister()
* clk-mediatek:
clk: mediatek: clk-mt8173-apmixedsys: Use common error handling code in clk_mt8173_apmixed_probe()
clk: mediatek: add infracfg reset controller for mt7988
dt-bindings: reset: mediatek: add MT7988 infracfg reset IDs
dt-bindings: clock: mediatek: convert SSUSBSYS to the json-schema clock
dt-bindings: clock: mediatek: convert PCIESYS to the json-schema clock
dt-bindings: clock: mediatek: convert hifsys to the json-schema clock
clk: mediatek: mt7981-topckgen: flag SGM_REG_SEL as critical
clk: mediatek: mt8183: Correct parent of CLK_INFRA_SSPM_32K_SELF
clk: mediatek: mt7622-apmixedsys: Fix an error handling path in clk_mt8135_apmixed_probe()
clk: mediatek: mt8135: Fix an error handling path in clk_mt8135_apmixed_probe()
* clk-bulk:
clk: Provide managed helper to get and enable bulk clocks
|
