| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 2ba8425678af422da37b6c9b50e9ce66f0f55cae ]
Since the CONFIG_CTL register is only 32 bits wide in the Stromer
and Stromer Plus PLLs , the 'config_ctl_hi_val' values from the
IPQ5018 and IPQ5332 configurations are not used so remove those.
No functional changes.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240509-stromer-config-ctl-v1-1-6034e17b28d5@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a33a64524e6381c399e5e42571d9363ffc0bed4 ]
The clk_alpha_pll_stromer_plus_set_rate() function does not
sets the ALPHA_EN bit in the USER_CTL register, so setting
rates which requires using alpha mode works only if the bit
gets set already prior calling the function.
Extend the function to set the ALPHA_EN bit in order to allow
using fractional rates regardless whether the bit gets set
previously or not.
Fixes: 84da48921a97 ("clk: qcom: clk-alpha-pll: introduce stromer plus ops")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240508-stromer-plus-alpha-en-v1-1-6639ce01ca5b@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3414f41a13eb41db15c558fbc695466203dca4fa ]
Both gpll6 and gpll7 are parented to CXO at 19.2 MHz and not to GPLL0
which runs at 600 MHz. Also gpll6_out_even should have the parent gpll6
and not gpll0.
Adjust the parents of these clocks to make Linux report the correct rate
and not absurd numbers like gpll7 at ~25 GHz or gpll6 at 24 GHz.
Corrected rates are the following:
gpll7 807999902 Hz
gpll6 768000000 Hz
gpll6_out_even 384000000 Hz
gpll0 600000000 Hz
gpll0_out_odd 200000000 Hz
gpll0_out_even 300000000 Hz
And because gpll6 is the parent of gcc_sdcc2_apps_clk_src (at 202 MHz)
that clock also reports the correct rate now and avoids this warning:
[ 5.984062] mmc0: Card appears overclocked; req 202000000 Hz, actual 6312499237 Hz
Fixes: 131abae905df ("clk: qcom: Add SM6350 GCC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240508-sm6350-gpll-fix-v1-1-e4ea34284a6d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 72ceafb587a56e26c905472418c7dc2033c294d3 upstream.
The crypto_ahb and crypto_axi clks are hardware voteable.
This means that the halt bit isn't reliable because some
other voter in the system, e.g. TrustZone, could be keeping
the clk enabled when the kernel turns it off from clk_disable().
Make these clks use voting mode by changing the halt check to
BRANCH_HALT_VOTED and toggle the voting bit in the voting register
instead of directly controlling the branch by writing to the branch
register. This fixes stuck clk warnings seen on ipq9574 and saves
power by actually turning the clk off.
Also changes the CRYPTO_AHB_CLK_ENA & CRYPTO_AXI_CLK_ENA
offset to 0xb004 from 0x16014.
Cc: stable@vger.kernel.org
Fixes: f6b2bd9cb29a ("clk: qcom: gcc-ipq9574: Enable crypto clocks")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://lore.kernel.org/r/20240509105405.1262369-1-quic_mdalam@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fce38e2a1a97900989d9fedebcf5a4dacdaee30 upstream.
Booting v6.8 results in a hang on various IPQ5018 based boards.
Investigating the problem showed that the hang happens when the
clk_alpha_pll_stromer_plus_set_rate() function tries to write
into the PLL_MODE register of the APSS PLL.
Checking the downstream code revealed that it uses [1] stromer
specific operations for IPQ5018, whereas in the current code
the stromer plus specific operations are used.
The ops in the 'ipq_pll_stromer_plus' clock definition can't be
changed since that is needed for IPQ5332, so add a new alpha pll
clock declaration which uses the correct stromer ops and use this
new clock for IPQ5018 to avoid the boot failure.
Also, change pll_type in 'ipq5018_pll_data' to
CLK_ALPHA_PLL_TYPE_STROMER to better reflect that it is a Stromer
PLL and change the apss_ipq_pll_probe() function accordingly.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c#L67
Cc: stable@vger.kernel.org
Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Tested-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240315-apss-ipq-pll-ipq5018-hang-v2-1-6fe30ada2009@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c5b3e17b8fd1f1add5a9477306c355fab126977 upstream.
The clk_alpha_pll_stromer_set_rate() function writes inproper
values into the ALPHA_VAL{,_U} registers which results in wrong
clock rates when the alpha value is used.
The broken behaviour can be seen on IPQ5018 for example, when
dynamic scaling sets the CPU frequency to 800000 KHz. In this
case the CPU cores are running only at 792031 KHz:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
792031
This happens because the function ignores the fact that the alpha
value calculated by the alpha_pll_round_rate() function is only
32 bits wide which must be extended to 40 bits if it is used on
a hardware which supports 40 bits wide values.
Extend the clk_alpha_pll_stromer_set_rate() function to convert
the alpha value to 40 bits before wrinting that into the registers
in order to ensure that the hardware really uses the requested rate.
After the change the CPU frequency is correct:
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
800000
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
800000
Cc: stable@vger.kernel.org
Fixes: e47a4f55f240 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20240328-alpha-pll-fix-stromer-set-rate-v3-1-1b79714c78bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c55f7ee2ec239b6afd8639c7ac06493876deb0ea ]
According to ipq5018.dtsi, the maximum supported rate by the
CPU is 1.008 GHz on the IPQ5018 platform, however the current
configuration of the PLL results in 1.2 GHz rate.
Change the 'L' value in the PLL configuration to limit the
rate to 1.008 GHz. The downstream kernel also uses the same
value [1]. Also add a comment to indicate the desired
frequency.
[1] https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c?ref_type=heads#L151
Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240326-fix-ipq5018-apss-pll-rate-v1-1-82ab31c9da7e@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07fb0a76bb757990b99fc2ab78ad7d1709cc441d ]
CONFIG_SM_GCC_8650 depends on ARM64 but it is selected by
CONFIG_SM_GPUCC_8650, which can be selected on ARM, resulting in a
Kconfig warning.
WARNING: unmet direct dependencies detected for SM_GCC_8650
Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=y] && (ARM64 || COMPILE_TEST [=n])
Selected by [y]:
- SM_GPUCC_8650 [=y] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=y]
Add the same dependencies to CONFIG_SM_GPUCC_8650 to resolve the
warning.
Fixes: 8676fd4f3874 ("clk: qcom: add the SM8650 GPU Clock Controller driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240318-fix-some-qcom-kconfig-deps-v1-2-ea0773e3df5a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e00f2540a581f8b8c165e5ae8afe52e4ad038550 ]
CONFIG_SC_GCC_8280XP depends on ARM64 but it is selected by
CONFIG_SC_CAMCC_8280XP, which can be selected on ARM, resulting in a
Kconfig warning.
WARNING: unmet direct dependencies detected for SC_GCC_8280XP
Depends on [n]: COMMON_CLK [=y] && COMMON_CLK_QCOM [=y] && (ARM64 || COMPILE_TEST [=n])
Selected by [y]:
- SC_CAMCC_8280XP [=y] && COMMON_CLK [=y] && COMMON_CLK_QCOM [=y]
Add the same dependencies to CONFIG_SC_CAMCC_8280XP to resolve the
warning.
Fixes: ff93872a9c61 ("clk: qcom: camcc-sc8280xp: Add sc8280xp CAMCC")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240318-fix-some-qcom-kconfig-deps-v1-1-ea0773e3df5a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e20ae5ae9f0c843aded4f06f3d1cab7384789e92 ]
Right now, msm8998 video decoder (venus) is non-functional:
$ time mpv --hwdec=v4l2m2m-copy --vd-lavc-software-fallback=no --vo=null --no-audio --untimed --length=30 --quiet demo-480.webm
(+) Video --vid=1 (*) (vp9 854x480 29.970fps)
Audio --aid=1 --alang=eng (*) (opus 2ch 48000Hz)
[ffmpeg/video] vp9_v4l2m2m: output VIDIOC_REQBUFS failed: Connection timed out
[ffmpeg/video] vp9_v4l2m2m: no v4l2 output context's buffers
[ffmpeg/video] vp9_v4l2m2m: can't configure decoder
Could not open codec.
Software decoding fallback is disabled.
Exiting... (Quit)
Bryan O'Donoghue suggested the proper fix:
- Set required register offsets in venus GDSC structs.
- Set HW_CTRL flag.
$ time mpv --hwdec=v4l2m2m-copy --vd-lavc-software-fallback=no --vo=null --no-audio --untimed --length=30 --quiet demo-480.webm
(+) Video --vid=1 (*) (vp9 854x480 29.970fps)
Audio --aid=1 --alang=eng (*) (opus 2ch 48000Hz)
[ffmpeg/video] vp9_v4l2m2m: VIDIOC_G_FMT ioctl
[ffmpeg/video] vp9_v4l2m2m: VIDIOC_G_FMT ioctl
...
Using hardware decoding (v4l2m2m-copy).
VO: [null] 854x480 nv12
Exiting... (End of file)
real 0m3.315s
user 0m1.277s
sys 0m0.453s
NOTES:
GDSC = Globally Distributed Switch Controller
Use same code as mmcc-msm8996 with:
s/venus_gdsc/video_top_gdsc/
s/venus_core0_gdsc/video_subcore0_gdsc/
s/venus_core1_gdsc/video_subcore1_gdsc/
https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/caf_migration/kernel.lnx.4.4.r38-rel/include/dt-bindings/clock/msm-clocks-hwio-8996.h
https://git.codelinaro.org/clo/la/kernel/msm-4.4/-/blob/caf_migration/kernel.lnx.4.4.r38-rel/include/dt-bindings/clock/msm-clocks-hwio-8998.h
0x1024 = MMSS_VIDEO GDSCR (undocumented)
0x1028 = MMSS_VIDEO_CORE_CBCR
0x1030 = MMSS_VIDEO_AHB_CBCR
0x1034 = MMSS_VIDEO_AXI_CBCR
0x1038 = MMSS_VIDEO_MAXI_CBCR
0x1040 = MMSS_VIDEO_SUBCORE0 GDSCR (undocumented)
0x1044 = MMSS_VIDEO_SUBCORE1 GDSCR (undocumented)
0x1048 = MMSS_VIDEO_SUBCORE0_CBCR
0x104c = MMSS_VIDEO_SUBCORE1_CBCR
Fixes: d14b15b5931c2b ("clk: qcom: Add MSM8998 Multimedia Clock Controller (MMCC) driver")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/ff4e2e34-a677-4c39-8c29-83655c5512ae@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 615a292ee4d51303246278f3fa33cc38700fe00e ]
On SM8650 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display af54000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 9e939f008338 ("clk: qcom: add the SM8650 Display Clock Controller driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-4-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e90b5139da8465a15c3820b4b67ca9468dce93b4 ]
On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 90114ca11476 ("clk: qcom: add SM8550 DISPCC driver")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-3-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1113501cfb46d5c0eb960f0a8a9f6c0f91dc6fb6 ]
On SM6350 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 837519775f1d ("clk: qcom: Add display clock controller driver for SM6350")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-2-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e801038a02ce1e8c652a0b668dd233a4ee48aeb7 ]
On SM8450 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 16fb89f92ec4 ("clk: qcom: Add support for Display Clock Controller on SM8450")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-1-b44038f3fa96@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f2bc4acbb1916b8cd2ce4bb3ba7b1cd7cb705fa ]
The offset of the CONFIG_CTL_U register defined for the Stromer
PLL is wrong. It is not aligned on a 4 bytes boundary which might
causes errors in regmap operations.
Maybe the intention behind of using the 0xff value was to indicate
that the register is not implemented in the PLL, but this is not
verified anywhere in the code. Moreover, this value is not used
even in other register offset arrays despite that those PLLs also
have unimplemented registers.
Additionally, on the Stromer PLLs the current code only touches
the CONFIG_CTL_U register if the result of pll_has_64bit_config()
is true which condition is not affected by the change.
Due to the reasons above, simply remove the CONFIG_CTL_U entry
from the Stromer specific array.
Fixes: e47a4f55f240 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-1-f7c0c5607cca@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
During rework somehow msm8976 num_clk got removed, restore it.
Fixes: d6edc31f3a68 ("clk: qcom: smd-rpm: Separate out interconnect bus clocks")
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240401171641.8979-1-a39.skl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Since commit deebc79b28d6 ("clk: qcom: gpucc-sc8280xp: Add external
supply for GX gdsc") the GDSC supply must be treated as optional to
avoid warnings like:
gpu_cc-sc8280xp 3d90000.clock-controller: supply vdd-gfx not found, using dummy regulator
on SC8280XP.
Fortunately, the driver is already prepared to handle this by checking
that the regulator pointer is non-NULL before use.
This also avoids triggering a potential deadlock on SC8280XP even if the
underlying issue still remains for the derivative platforms like SA8295P
that actually use the supply.
Fixes: deebc79b28d6 ("clk: qcom: gpucc-sc8280xp: Add external supply for GX gdsc")
Link: https://lore.kernel.org/lkml/Zf25Sv2x9WaCFuIH@hovoldconsulting.com/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240325085835.26158-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The current register offset used for the GCC_UBI0_AXI_ARES reset
seems wrong. Or at least, the downstream driver uses [1] the same
offset which is used for other the GCC_UBI0_*_ARES resets.
Change the code to use the same offset used in the downstream
driver and also specify the reset bit explicitly to use the
same format as the followup entries.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4.r4/drivers/clk/qcom/gcc-ipq5018.c?ref_type=heads#L3773
Fixes: e3fdbef1bab8 ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240225-gcc-ipq5018-register-fixes-v1-3-3c191404d9f0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The following table shows the values of the 'halt_reg' and the
'enable_reg' fields from the pcie clocks defined in the current
driver:
clock halt_reg enable_reg
gcc_pcie0_ahb_clk 0x75010 0x75010
gcc_pcie0_aux_clk 0x75014 0x75014
gcc_pcie0_axi_m_clk 0x75008 0x75008
gcc_pcie0_axi_s_bridge_clk 0x75048 0x75048
gcc_pcie0_axi_s_clk 0x7500c 0x7500c
gcc_pcie0_pipe_clk 0x75018 0x75018
gcc_pcie1_ahb_clk 0x76010 0x76010
gcc_pcie1_aux_clk 0x76014 0x76014
gcc_pcie1_axi_m_clk 0x76008 0x76008
gcc_pcie1_axi_s_bridge_clk 0x76048 0x76048
gcc_pcie1_axi_s_clk 0x7600c 0x7600c
gcc_pcie1_pipe_clk 8* 0x76018
Based on the table, it is quite likely that the pcie0 and the pci1
clocks are using the same register layout, however it seems that
the value of the 'halt_reg' field in the 'gcc_pcie1_pipe_clk' clock
is wrong.
In the downstream driver [1], the same '0x76018' value is used for
both the 'halt_reg' and for the 'enable_reg' fields of the
'gcc_pcie1_pipe_clk' clock.
Update the current driver to use the same value used downstream as
probably that is the correct value.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4.r4/drivers/clk/qcom/gcc-ipq5018.c?ref_type=heads#L2316
Fixes: e3fdbef1bab8 ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240225-gcc-ipq5018-register-fixes-v1-2-3c191404d9f0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The value of the 'enable_reg' field in the 'gcc_gmac0_sys_clk'
clock definition seems wrong as it is greater than the
'max_register' value defined in the regmap configuration.
Additionally, all other gmac specific branch clock definitions
within the driver uses the same value both for the 'enable_reg'
and for the 'halt_reg' fields.
Due to the lack of documentation the correct value is not known.
Looking into the downstream driver does not help either, as that
uses the same (presumably wrong) value [1].
Nevertheless, change the 'enable_reg' field of 'gcc_gmac0_sys_clk'
to use the value from the 'halt_reg' field so it follows the pattern
used in other gmac clock definitions. The change is based on the
assumption that the register layout of this clock is the same
as the other gmac clocks.
1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4.r4/drivers/clk/qcom/gcc-ipq5018.c?ref_type=heads#L1889
Fixes: e3fdbef1bab8 ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20240225-gcc-ipq5018-register-fixes-v1-1-3c191404d9f0@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The desired DT pattern for clock indexing is the following:
clocks = <&gcc GCC_CAMERA_AHB_CLK>,
<&bi_tcxo_div2>,
<&bi_tcxo_ao_div2>,
<&sleep_clk>;
In order to facilitate that indexing structure we need to have DT_IFACE
enum defined.
Fixes: 76126a5129b5 ("clk: qcom: Add camcc clock driver for x1e80100")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240302-linux-next-24-03-01-simple-clock-fixes-v1-2-25f348a5982b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-7-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: 2b46cd23a5a2 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-6-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: ff93872a9c61 ("clk: qcom: camcc-sc8280xp: Add sc8280xp CAMCC")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-5-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: d75b82cff488 ("clk: qcom: Add Global Clock Controller driver for IPQ9574")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-4-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: 9607f6224b39 ("clk: qcom: ipq8074: add PCIE, USB and SDCC clocks")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-3-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Only compile tested.
Fixes: d9db07f088af ("clk: qcom: Add ipq6018 Global Clock Controller support")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-2-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The frequency table arrays are supposed to be terminated with an
empty element. Add such entry to the end of the arrays where it
is missing in order to avoid possible out-of-bound access when
the table is traversed by functions like qcom_find_freq() or
qcom_find_freq_floor().
Fixes: e3fdbef1bab8 ("clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240229-freq-table-terminator-v1-1-074334f0905c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
SDM845 downstream uses non-default values for GDSC internal waits.
Program them accordingly to avoid surprises.
Fixes: 81351776c9fb ("clk: qcom: Add display clock controller driver for SDM845")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # OnePlus 6
Link: https://lore.kernel.org/r/20240103-topic-845gdsc-v1-1-368efbe1a61d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
This driver has never been used in the DT files merged to the kernel.
According to Sibi, it only worked on the pre-production devices. For the
production devices this functionality has been moved to the firmware.
Drop the driver to remove possible confusion.
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240216-drop-sc7180-mss-v1-1-0a8dc8d71c0c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Instead of magically poking at the bit0 of branch clocks' CBCR, use
the newly introduced helper.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212-topic-clk_branch_en-v7-2-5b79eb7278b2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
We hardcode some clocks to be always-on, as they're essential to the
functioning of the SoC / some peripherals. Add a helper to do so
to make the writes less magic.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212-topic-clk_branch_en-v7-1-5b79eb7278b2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The clk_init_data and pll_vco structures are never modified, make
them const.
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Link: https://lore.kernel.org/r/20240201-dispcc-sm8150-v1-1-cbeb89015e5d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add missing QREF clocks for UFS MEM and UFS CARD controllers.
Fixes: 4433594bbe5d ("clk: qcom: gcc: Add global clock controller driver for SC8180x")
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-4-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add new entries in the gcc driver for some more resets found on MSM8953.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
[luca: expand commit message, move entry, add more entries]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-mdss-reset-v2-2-fd7824559426@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no need to register video clock controllers during subsys init
calls. Use module_platform_driver() instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-4-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no need to register GPU clock controllers during subsys init
calls. Use module_platform_driver() instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-3-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no need to register display clock controllers during subsys init
calls. Use module_platform_driver() instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-2-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no need to register camera clock controllers during subsys init
calls. Use module_platform_driver() instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-1-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value for SM8550 is known and extracted from the msm-5.15 driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-18-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value is known for SM8450, see [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/commit/d0730ea5867264ee50b793f6700eb6a376ddcbbb
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-17-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value is known for SM8350, see [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/commit/dfe241edf23daf3c1ccbb79b02798965123fad98
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-16-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value was obtained by referencing the msm-4.14/19 driver, which uses a
single value for all platforms [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/blob/LA.UM.9.15.c26/msm/vidc/hfi_common.c?ref_type=heads#L3662-3663
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-15-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value was obtained by referencing the msm-4.14/19 driver, which uses a
single value for all platforms [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/blob/LA.UM.9.15.c26/msm/vidc/hfi_common.c?ref_type=heads#L3662-3663
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-14-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The Venus hw on 8650 is similar to the one on 8550, follow its
requirements.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-13-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value for SM8550 is known and extracted from the msm-5.15 driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-12-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value is known for SM8450, see [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/commit/d0730ea5867264ee50b793f6700eb6a376ddcbbb
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-11-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value is known for SM8350, see [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/commit/dfe241edf23daf3c1ccbb79b02798965123fad98
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-10-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value was obtained by referencing the msm-4.19 driver, which uses a
single value for all platforms [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/blob/LA.UM.9.15.c26/msm/vidc/hfi_common.c?ref_type=heads#L3662-3663
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-9-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Some Venus resets may require more time when toggling. Describe that.
The value was obtained by referencing the msm-4.14/19 driver, which uses a
single value for all platforms [1].
[1] https://git.codelinaro.org/clo/la/platform/vendor/opensource/video-driver/-/blob/LA.UM.9.15.c26/msm/vidc/hfi_common.c?ref_type=heads#L3662-3663
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240105-topic-venus_reset-v2-8-c37eba13b5ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
