| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 4183a7be77009fc31c5760429fe095f163bf96a9 ]
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 88e72239ead9814b886db54fc4ee39ef3c2b8f26 upstream.
Commit 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed
serdev") will cause below regression issue:
BT can't be enabled after below steps:
cold boot -> enable BT -> disable BT -> warm reboot -> BT enable failure
if property enable-gpios is not configured within DT|ACPI for QCA6390.
The commit is to fix a use-after-free issue within qca_serdev_shutdown()
by adding condition to avoid the serdev is flushed or wrote after closed
but also introduces this regression issue regarding above steps since the
VSC is not sent to reset controller during warm reboot.
Fixed by sending the VSC to reset controller within qca_serdev_shutdown()
once BT was ever enabled, and the use-after-free issue is also fixed by
this change since the serdev is still opened before it is flushed or wrote.
Verified by the reported machine Dell XPS 13 9310 laptop over below two
kernel commits:
commit e00fc2700a3f ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of bluetooth-next tree.
commit b23d98d46d28 ("Bluetooth: btusb: Fix triggering coredump
implementation for QCA") of linus mainline tree.
Fixes: 272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Cc: stable@vger.kernel.org
Reported-by: Wren Turkal <wt@penguintechs.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218726
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Wren Turkal <wt@penguintechs.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed2a2ef16a6b9197a0e452308bf6acee6e01f709 upstream.
Some Broadcom controllers found on Apple Silicon machines abuse the
reserved bits inside the PHY fields of LE Extended Advertising Report
events for additional flags. Add a quirk to drop these and correctly
extract the Primary/Secondary_PHY field.
The following excerpt from a btmon trace shows a report received with
"Reserved" for "Primary PHY" on a 4388 controller:
> HCI Event: LE Meta Event (0x3e) plen 26
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2515
Props: 0x0015
Connectable
Directed
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2515)
Address type: Random (0x01)
Address: 00:00:00:00:00:00 (Static)
Primary PHY: Reserved
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -60 dBm (0xc4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (Apple, Inc.)
Data length: 0x00
Cc: stable@vger.kernel.org
Fixes: 2e7ed5f5e69b ("Bluetooth: hci_sync: Use advertised PHYs on hci_le_ext_create_conn_sync")
Reported-by: Janne Grunau <j@jannau.net>
Closes: https://lore.kernel.org/all/Zjz0atzRhFykROM9@robin
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 897e6120566f1c108b85fefe78d1c1bddfbd5988 upstream.
We are releasing a single msgid, so the order argument to
bitmap_release_region must be zero.
Fixes: 8a06127602de ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 68aa21054ec3a1a313af90a5f95ade16c3326d20 ]
This fixes some CHECKs reported by the checkpatch script.
Issues reported in ath3k.c:
-------
ath3k.c
-------
CHECK: Please don't use multiple blank lines
+
+
CHECK: Blank lines aren't necessary after an open brace '{'
+static const struct usb_device_id ath3k_blist_tbl[] = {
+
CHECK: Alignment should match open parenthesis
+static int ath3k_load_firmware(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Alignment should match open parenthesis
+static int ath3k_get_version(struct usb_device *udev,
+ struct ath3k_version *version)
CHECK: Alignment should match open parenthesis
+static int ath3k_load_fwfile(struct usb_device *udev,
+ const struct firmware *firmware)
CHECK: Alignment should match open parenthesis
+ err = usb_bulk_msg(udev, pipe, send_buf, size,
+ &len, 3000);
CHECK: Unnecessary parentheses around 'len != size'
+ if (err || (len != size)) {
CHECK: Blank lines aren't necessary after an open brace '{'
+ switch (fw_version.ref_clock) {
+
CHECK: Alignment should match open parenthesis
+ snprintf(filename, ATH3K_NAME_LEN, "ar3k/ramps_0x%08x_%d%s",
+ le32_to_cpu(fw_version.rom_version), clk_value, ".dfu");
CHECK: Alignment should match open parenthesis
+static int ath3k_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" not found",
+ ATH3K_FIRMWARE);
CHECK: Alignment should match open parenthesis
+ BT_ERR("Firmware file \"%s\" request failed (err=%d)",
+ ATH3K_FIRMWARE, ret);
total: 0 errors, 0 warnings, 14 checks, 540 lines checked
Signed-off-by: Uri Arev <me@wantyapps.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84a4bb6548a29326564f0e659fb8064503ecc1c7 ]
Since BT_HS has been remove HCI_AMP controllers no longer has any use so
remove it along with the capability of creating AMP controllers.
Since we no longer need to differentiate between AMP and Primary
controllers, as only HCI_PRIMARY is left, this also remove
hdev->dev_type altogether.
Fixes: e7b02296fb40 ("Bluetooth: Remove BT_HS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a189f0ee6685457528db7a36ded3085e5d13ddc3 ]
Return -ENOMEM on allocation failure. Don't return success.
Fixes: cda0d6a198e2 ("Bluetooth: qca: fix info leak when fetching fw build id")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 958cd6beab693f395ffe07814ef77d2b45e8b0fc upstream.
Because both MT7920 and MT7921 use the same chip ID.
We use the 8th bit of fw_flavor to distingush MT7920.
The original patch made a mistake to check whole fw_flavor,
that makes the condition both true (dev_id == 0x7961 && fw_flavor),
and makes MT7921 flow wrong.
In this patch, we correct the flow to get the 8th bit value for MT7920.
And the patch is verified pass with both MT7920 and MT7921.
Signed-off-by: Peter Tsao <peter.tsao@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent commit fixed the code that parses the firmware files before
downloading them to the controller but introduced a memory leak in case
the sanity checks ever fail.
Make sure to free the firmware buffer before returning on errors.
Fixes: f905ae0be4b7 ("Bluetooth: qca: add missing firmware sanity checks")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the missing sanity check when fetching the board id to avoid leaking
slab data when later requesting the firmware.
Fixes: a7f8dedb4be2 ("Bluetooth: qca: add support for QCA2066")
Cc: stable@vger.kernel.org # 6.7
Cc: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the missing sanity checks and move the 255-byte build-id buffer off
the stack to avoid leaking stack data through debugfs in case the
build-info reply is malformed.
Fixes: c0187b0bd3e9 ("Bluetooth: btqca: Add support to read FW build version for WCN3991 BTSoC")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The default device address apparently comes from the NVM configuration
file and can differ quite a bit between controllers.
Store the default address when parsing the configuration file and use it
to determine whether the controller has been provisioned with an
address.
This makes sure that devices without a unique address start as
unconfigured unless a valid address has been provided in the devicetree.
Fixes: 32868e126c78 ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The NVM configuration files used by WCN3988 and WCN3990/1/8 have two
sets of configuration tags that are enclosed by a type-length header of
type four which the current parser fails to account for.
Instead the driver happily parses random data as if it were valid tags,
something which can lead to the configuration data being corrupted if it
ever encounters the words 0x0011 or 0x001b.
As is clear from commit b63882549b2b ("Bluetooth: btqca: Fix the NVM
baudrate tag offcet for wcn3991") the intention has always been to
process the configuration data also for WCN3991 and WCN3998 which
encodes the baud rate at a different offset.
Fix the parser so that it can handle the WCN3xxx configuration files,
which has an enclosing type-length header of type four and two sets of
TLV tags enclosed by a type-length header of type two and three,
respectively.
Note that only the first set, which contains the tags the driver is
currently looking for, will be parsed for now.
With the parser fixed, the software in-band sleep bit will now be set
for WCN3991 and WCN3998 (as it is for later controllers) and the default
baud rate 3200000 may be updated by the driver also for WCN3xxx
controllers.
Notably the deep-sleep feature bit is already set by default in all
configuration files in linux-firmware.
Fixes: 4219d4686875 ("Bluetooth: btqca: Add wcn3990 firmware download support.")
Cc: stable@vger.kernel.org # 4.19
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the missing sanity checks when parsing the firmware files before
downloading them to avoid accessing and corrupting memory beyond the
vmalloced buffer.
Fixes: 83e81961ff7e ("Bluetooth: btqca: Introduce generic QCA ROME support")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This address is now used to determine if a controller has a valid
address or if one needs to be provided through devicetree or by user
space before the controller can be used.
It turns out that the WCN3991 controllers used in Chromium Trogdor
machines use a different default address, 39:98:00:00:5a:ad, which also
needs to be marked as invalid so that the correct address is fetched
from the devicetree.
Qualcomm has unfortunately not yet provided any answers as to whether
the 39:98 encodes a hardware id and if there are other variants of the
default address that needs to be handled by the driver.
For now, add the Trogdor WCN3991 default address to the device address
check to avoid having these controllers start with the default address
instead of their assigned addresses.
Fixes: 32868e126c78 ("Bluetooth: qca: fix invalid device address check")
Cc: stable@vger.kernel.org # 6.5
Cc: Doug Anderson <dianders@chromium.org>
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c58 ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c58 ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal" <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c657 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c657
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160eaf1 ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_devcd_append() would free the skb on error so the caller don't
have to free it again otherwise it would cause the double free of skb.
Fixes: 0b7015132878 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Reported-by : Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de44c ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific
command to trigger firmware coredump, but the command does not
have any event as its sync response, so it is not suitable to use
__hci_cmd_sync(), fixed by using __hci_cmd_send().
Fixes: 20981ce2d5a5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the support ID(0x0bda, 0x4853) to usb_device_id table for
Realtek RTL8852BE.
Without this change the device utilizes an obsolete version of
the firmware that is encoded in it rather than the updated Realtek
firmware and config files from the firmware directory. The latter
files implement many new features.
The device table is as follows:
T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=4853 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Cc: stable@vger.kernel.org
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8be ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts commit 7dcd3e014aa7faeeaf4047190b22d8a19a0db696.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc81a ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014aa7 ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
|
|
The ATS2851 controller erroneously reports support for the "Read
Encryption Key Length" HCI command. This makes it unable to connect
to any devices, since this command is issued by the kernel during the
connection process in response to an "Encryption Change" HCI event.
Add a new quirk (HCI_QUIRK_BROKEN_ENC_KEY_SIZE) to hint that the command
is unsupported, preventing it from interrupting the connection process.
This is the error log from btmon before this patch:
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 2048 Address: ...
Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
Handle: 2048 Address: ...
> HCI Event: Command Status (0x0f) plen 4
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Vinicius Peixoto <nukelet64@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch is added support Mediatek MT7920
The firmware location of MT7920 will set to
/lib/firmware/mediatek/
The information in /sys/kernel/debug/usb/devices about MT7920U
Bluetooth device is listed as the below
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 12 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0e8d ProdID=7920 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Peter Tsao <peter.tsao@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.
This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Fix scheduling while atomic BUG in btnxpuart_close(), properly
purge the transmit queue and free the receive skb.
[ 10.973809] BUG: scheduling while atomic: kworker/u9:0/80/0x00000002
...
[ 10.980740] CPU: 3 PID: 80 Comm: kworker/u9:0 Not tainted 6.8.0-rc7-0.0.0-devel-00005-g61fdfceacf09 #1
[ 10.980751] Hardware name: Toradex Verdin AM62 WB on Dahlia Board (DT)
[ 10.980760] Workqueue: hci0 hci_power_off [bluetooth]
[ 10.981169] Call trace:
...
[ 10.981363] uart_update_mctrl+0x58/0x78
[ 10.981373] uart_dtr_rts+0x104/0x114
[ 10.981381] tty_port_shutdown+0xd4/0xdc
[ 10.981396] tty_port_close+0x40/0xbc
[ 10.981407] uart_close+0x34/0x9c
[ 10.981414] ttyport_close+0x50/0x94
[ 10.981430] serdev_device_close+0x40/0x50
[ 10.981442] btnxpuart_close+0x24/0x98 [btnxpuart]
[ 10.981469] hci_dev_close_sync+0x2d8/0x718 [bluetooth]
[ 10.981728] hci_dev_do_close+0x2c/0x70 [bluetooth]
[ 10.981862] hci_power_off+0x20/0x64 [bluetooth]
Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b7015132878 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The problem is detected by KASAN.
btrtl driver uses private hci data to store 'struct btrealtek_data'.
If btrtl driver is used with btusb, then memory for private hci data
is allocated in btusb. But no private data is allocated after hci_dev,
when btrtl is used with hci_h5.
This commit adds memory allocation for hci_h5 case.
==================================================================
BUG: KASAN: slab-out-of-bounds in btrtl_initialize+0x6cc/0x958 [btrtl]
Write of size 8 at addr ffff00000f5a5748 by task kworker/u9:0/76
Hardware name: Pine64 PinePhone (1.2) (DT)
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
dump_backtrace+0x9c/0x128
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
print_report+0xf8/0x5d8
kasan_report+0x90/0xd0
__asan_store8+0x9c/0xc0
[btrtl]
h5_btrtl_setup+0xd0/0x2f8 [hci_uart]
h5_setup+0x50/0x80 [hci_uart]
hci_uart_setup+0xd4/0x260 [hci_uart]
hci_dev_open_sync+0x1cc/0xf68 [bluetooth]
hci_dev_do_open+0x34/0x90 [bluetooth]
hci_power_on+0xc4/0x3c8 [bluetooth]
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Allocated by task 53:
kasan_save_stack+0x3c/0x68
kasan_save_track+0x20/0x40
kasan_save_alloc_info+0x68/0x78
__kasan_kmalloc+0xd4/0xd8
__kmalloc+0x1b4/0x3b0
hci_alloc_dev_priv+0x28/0xa58 [bluetooth]
hci_uart_register_device+0x118/0x4f8 [hci_uart]
h5_serdev_probe+0xf4/0x178 [hci_uart]
serdev_drv_probe+0x54/0xa0
really_probe+0x254/0x588
__driver_probe_device+0xc4/0x210
driver_probe_device+0x64/0x160
__driver_attach_async_helper+0x88/0x158
async_run_entry_fn+0xd0/0x388
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Last potentially related work creation:
kasan_save_stack+0x3c/0x68
__kasan_record_aux_stack+0xb0/0x150
kasan_record_aux_stack_noalloc+0x14/0x20
__queue_work+0x33c/0x960
queue_work_on+0x98/0xc0
hci_recv_frame+0xc8/0x1e8 [bluetooth]
h5_complete_rx_pkt+0x2c8/0x800 [hci_uart]
h5_rx_payload+0x98/0xb8 [hci_uart]
h5_recv+0x158/0x3d8 [hci_uart]
hci_uart_receive_buf+0xa0/0xe8 [hci_uart]
ttyport_receive_buf+0xac/0x178
flush_to_ldisc+0x130/0x2c8
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
Second to last potentially related work creation:
kasan_save_stack+0x3c/0x68
__kasan_record_aux_stack+0xb0/0x150
kasan_record_aux_stack_noalloc+0x14/0x20
__queue_work+0x788/0x960
queue_work_on+0x98/0xc0
__hci_cmd_sync_sk+0x23c/0x7a0 [bluetooth]
__hci_cmd_sync+0x24/0x38 [bluetooth]
btrtl_initialize+0x760/0x958 [btrtl]
h5_btrtl_setup+0xd0/0x2f8 [hci_uart]
h5_setup+0x50/0x80 [hci_uart]
hci_uart_setup+0xd4/0x260 [hci_uart]
hci_dev_open_sync+0x1cc/0xf68 [bluetooth]
hci_dev_do_open+0x34/0x90 [bluetooth]
hci_power_on+0xc4/0x3c8 [bluetooth]
process_one_work+0x328/0x6f0
worker_thread+0x410/0x778
kthread+0x168/0x178
ret_from_fork+0x10/0x20
==================================================================
Fixes: 5b355944b190 ("Bluetooth: btrtl: Add btrealtek data struct")
Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In some cases uart-base drivers may need to use priv data. For
example, to store information needed for devcoredump.
Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the following build regression:
drivers-bluetooth-btintel.c-btintel_read_version()-warn:
passing-zero-to-PTR_ERR
Fixes: b79e04091010 ("Bluetooth: btintel: Fix null ptr deref in btintel_read_version")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146a2 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use devm_kstrdup() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use strreplace() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.
Reported-and-tested-by: syzbot+830d9e3fa61968246abd@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3602 for MediaTek MT7925 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=10 Cnt=02 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3602 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Ulrik Strid <ulrik@strid.tech>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the tx timeout issue seen while running a stress test on
btnxpuart for couple of hours, such that the interval between two HCI
commands coincide with the power save timeout value of 2 seconds.
Test procedure using bash script:
<load btnxpuart.ko>
hciconfig hci0 up
//Enable Power Save feature
hcitool -i hci0 cmd 3f 23 02 00 00
while (true)
do
hciconfig hci0 leadv
sleep 2
hciconfig hci0 noleadv
sleep 2
done
Error log, after adding few more debug prints:
Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00
Bluetooth: hci0: Set UART break: on, status=0
Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled
Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00
Can't set advertise mode on hci0: Connection timed out (110)
Bluetooth: hci0: command 0x200a tx timeout
When the power save mechanism turns on UART break, and btnxpuart_tx_work()
is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE,
which prevents the psdata->work from being scheduled, which is responsible
to turn OFF UART break.
This issue is fixed by adding a ps_lock mutex around UART break on/off as
well as around ps_state read/write.
btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is
PS_STATE_SLEEP, it will first schedule psdata->work, and then it will
reschedule itself once UART break has been turned off and ps_state is
PS_STATE_AWAKE.
Tested above script for 50,000 iterations and TX timeout error was not
observed anymore.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the support for RTL8852BT/RTL8852BE-VT BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 8 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=8520 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Vendor-specific command patch config has HCI_Command_Complete event as
response, but qca_send_patch_config_cmd() wrongly expects vendor-specific
event for the command, fixed by using right event type.
Btmon log for the vendor-specific command are shown below:
< HCI Command: Vendor (0x3f|0x0000) plen 5
28 01 00 00 00
> HCI Event: Command Complete (0x0e) plen 5
Vendor (0x3f|0x0000) ncmd 1
Status: Success (0x00)
28
Fixes: 4fac8a7ac80b ("Bluetooth: btqca: sequential validation")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
receive_buf() is called from ttyport_receive_buf() that expects values
">= 0" from serdev_controller_receive_buf(), change its return type from
ssize_t to size_t.
The need for this clean-up was noticed while fixing a warning, see
commit 94d053942544 ("Bluetooth: btnxpuart: fix recv_buf() return value").
Changing the callback prototype to return an unsigned seems the best way
to document the API and ensure that is properly used.
GNSS drivers implementation of serdev receive_buf() callback return
directly the return value of gnss_insert_raw(). gnss_insert_raw()
returns a signed int, however this is not an issue since the value
returned is always positive, because of the kfifo_in() implementation.
gnss_insert_raw() could be changed to return also an unsigned, however
this is not implemented here as request by the GNSS maintainer Johan
Hovold.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com> # for platform/surface
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240122180551.34429-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
|
|
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This 13d3:3572 is part of Realtek RTW8852BE chip.
The device table is:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3572 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
