| Age | Commit message (Collapse) | Author |
|---|
|
Add the fsl,aips and fsl,emi compatible strings for legacy i.MX3 SoCs
(over 15 years old).
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260201011913.2419626-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Drop the gpio reset from the list of required properties. The bridge works
fine with a reset not managed by Linux. In the driver itself the gpio is
already flagged as optional.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Link: https://patch.msgid.link/20260130205820.83189-6-d.haller@phytec.de
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"By the number of commits, cpufreq is the leading party (again) and the
most visible change there is the removal of the omap-cpufreq driver
that has not been used for a long time (good riddance). There are also
quite a few changes in the cppc_cpufreq driver, mostly related to
fixing its frequency invariance engine in the case when the CPPC
registers used by it are not in PCC. In addition to that, support for
AM62L3 is added to the ti-cpufreq driver and the cpufreq-dt-platdev
list is updated for some platforms. The remaining cpufreq changes are
assorted fixes and cleanups.
Next up is cpuidle and the changes there are dominated by intel_idle
driver updates, mostly related to the new command line facility
allowing users to adjust the list of C-states used by the driver.
There are also a few updates of cpuidle governors, including two menu
governor fixes and some refinements of the teo governor, and a
MAINTAINERS update adding Christian Loehle as a cpuidle reviewer.
[Thanks for stepping up Christian!]
The most significant update related to system suspend and hibernation
is the one to stop freezing the PM runtime workqueue during system PM
transitions which allows some deadlocks to be avoided. There is also a
fix for possible concurrent bit field updates in the core device
suspend code and a few other minor fixes.
Apart from the above, several drivers are updated to discard the
return value of pm_runtime_put() which is going to be converted to a
void function as soon as everybody stops using its return value, PL4
support for Ice Lake is added to the Intel RAPL power capping driver,
and there are assorted cleanups, documentation fixes, and some
cpupower utility improvements.
Specifics:
- Remove the unused omap-cpufreq driver (Andreas Kemnade)
- Optimize error handling code in cpufreq_boost_trigger_state() and
make cpufreq_boost_trigger_state() return -EOPNOTSUPP if no policy
supports boost (Lifeng Zheng)
- Update cpufreq-dt-platdev list for tegra, qcom, TI (Aaron Kling,
Dhruva Gole, and Konrad Dybcio)
- Minor improvements to the cpufreq and cpumask rust implementation
(Alexandre Courbot, Alice Ryhl, Tamir Duberstein, and Yilin Chen)
- Add support for AM62L3 SoC to the ti-cpufreq driver (Dhruva Gole)
- Update arch_freq_scale in the CPPC cpufreq driver's frequency
invariance engine (FIE) in scheduler ticks if the related CPPC
registers are not in PCC (Jie Zhan)
- Assorted minor cleanups and improvements in ARM cpufreq drivers
(Juan Martinez, Felix Gu, Luca Weiss, and Sergey Shtylyov)
- Add generic helpers for sysfs show/store to cppc_cpufreq (Sumit
Gupta)
- Make the scaling_setspeed cpufreq sysfs attribute return the actual
requested frequency to avoid confusion (Pengjie Zhang)
- Simplify the idle CPU time granularity test in the ondemand cpufreq
governor (Frederic Weisbecker)
- Enable asym capacity in intel_pstate only when CPU SMT is not
possible (Yaxiong Tian)
- Update the description of rate_limit_us default value in cpufreq
documentation (Yaxiong Tian)
- Add a command line option to adjust the C-states table in the
intel_idle driver, remove the 'preferred_cstates' module parameter
from it, add C-states validation to it and clean it up (Artem
Bityutskiy)
- Make the menu cpuidle governor always check the time till the
closest timer event when the scheduler tick has been stopped to
prevent it from mistakenly selecting the deepest available idle
state (Rafael Wysocki)
- Update the teo cpuidle governor to avoid making suboptimal
decisions in certain corner cases and generally improve idle state
selection accuracy (Rafael Wysocki)
- Remove an unlikely() annotation on the early-return condition in
menu_select() that leads to branch misprediction 100% of the time
on systems with only 1 idle state enabled, like ARM64 servers
(Breno Leitao)
- Add Christian Loehle to MAINTAINERS as a cpuidle reviewer
(Christian Loehle)
- Stop flagging the PM runtime workqueue as freezable to avoid system
suspend and resume deadlocks in subsystems that assume asynchronous
runtime PM to work during system-wide PM transitions (Rafael
Wysocki)
- Drop redundant NULL pointer checks before acomp_request_free() from
the hibernation code handling image saving (Rafael Wysocki)
- Update wakeup_sources_walk_start() to handle empty lists of wakeup
sources as appropriate (Samuel Wu)
- Make dev_pm_clear_wake_irq() check the power.wakeirq value under
power.lock to avoid race conditions (Gui-Dong Han)
- Avoid bit field races related to power.work_in_progress in the core
device suspend code (Xuewen Yan)
- Make several drivers discard pm_runtime_put() return value in
preparation for converting that function to a void one (Rafael
Wysocki)
- Add PL4 support for Ice Lake to the Intel RAPL power capping driver
(Daniel Tang)
- Replace sprintf() with sysfs_emit() in power capping sysfs show
functions (Sumeet Pawnikar)
- Make dev_pm_opp_get_level() return value match the documentation
after a previous update of the latter (Aleks Todorov)
- Use scoped for each OF child loop in the OPP code (Krzysztof
Kozlowski)
- Fix a bug in an example code snippet and correct typos in the
energy model management documentation (Patrick Little)
- Fix miscellaneous problems in cpupower (Kaushlendra Kumar):
* idle_monitor: Fix incorrect value logged after stop
* Fix inverted APERF capability check
* Use strcspn() to strip trailing newline
* Reset errno before strtoull()
* Show C0 in idle-info dump
- Improve cpupower installation procedure by making the systemd step
optional and allowing users to disable the installation of
systemd's unit file (João Marcos Costa)"
* tag 'pm-6.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
PM: sleep: core: Avoid bit field races related to work_in_progress
PM: sleep: wakeirq: harden dev_pm_clear_wake_irq() against races
cpufreq: Documentation: Update description of rate_limit_us default value
cpufreq: intel_pstate: Enable asym capacity only when CPU SMT is not possible
PM: wakeup: Handle empty list in wakeup_sources_walk_start()
PM: EM: Documentation: Fix bug in example code snippet
Documentation: Fix typos in energy model documentation
cpuidle: governors: teo: Refine intercepts-based idle state lookup
cpuidle: governors: teo: Adjust the classification of wakeup events
cpufreq: ondemand: Simplify idle cputime granularity test
cpufreq: userspace: make scaling_setspeed return the actual requested frequency
PM: hibernate: Drop NULL pointer checks before acomp_request_free()
cpufreq: CPPC: Add generic helpers for sysfs show/store
cpufreq: scmi: Fix device_node reference leak in scmi_cpu_domain_id()
cpufreq: ti-cpufreq: add support for AM62L3 SoC
cpufreq: dt-platdev: Add ti,am62l3 to blocklist
cpufreq/amd-pstate: Add comment explaining nominal_perf usage for performance policy
cpufreq: scmi: correct SCMI explanation
cpufreq: dt-platdev: Block the driver from probing on more QC platforms
rust: cpumask: rename methods of Cpumask for clarity and consistency
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.0
This release is almost all abut driers, there's very little core work
here, although some of that driver work is in more generic areas like
SDCA and SOF:
- Generic SDCA support for reporting jack events.
- Continuing platform support, cleanup and feature improements for the
AMD, Intel, Qualcomm and SOF code.
- Platform description improvements for the Cirrus drivers.
- Support for NXP i.MX952, Realtek RT1320 and RT5575, and Sophogo
CV1800B.
We also pulled in one small SPI API update and some more substantial
regmap work (cache description improvements) for use in drivers.
|
|
Add HiTRON HAC300S PSU to trivial devices since it is simple PMBUS
capable device.
Since this is the first supported device from this vendor, document its
name to the vendor-prefixes.yaml file as well.
Signed-off-by: Vasileios Amoiridis <vasileios.amoiridis@cern.ch>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260119190806.35276-2-vassilisamir@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is a USB HID device which includes an I2C controller and 8 GPIO pins.
The binding allows describing the chip's gpio and i2c controller in DT,
with the i2c controller being bound to a subnode named "i2c". This is
intended to be used in configurations where the CP2112 is permanently
connected in hardware.
Signed-off-by: Danny Kaehn <danny.kaehn@plexus.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260127-cp2112-dt-v13-1-6448ddd4bf22@plexus.com
|
|
- Add DT binding and driver support for SA8255p Endpoint being managed by
firmware (Mrinmay Sarkar)
* pci/controller/dwc-qcom-ep:
PCI: qcom-ep: Add support for firmware-managed PCIe Endpoint
dt-bindings: PCI: qcom,sa8255p-pcie-ep: Document firmware managed PCIe endpoint
|
|
- Add DT binding and driver support for an optional external refclock in
addition to the refclock from the internal PLL (Richard Zhu)
- Apply i.MX95 ERR051586 erratum workaround (release CLKREQ# so endpoint
can assert it when required) during resume (Richard Zhu)
- Enable i.MX95 REFCLK by overriding CLKREQ# so it's driven by default
(Richard Zhu)
- Clear CLKREQ# override if link is up and DT says 'supports-clkreq' so
endpoints can use CLKREQ# to exit the L1.2 state (Richard Zhu)
* pci/controller/dwc-imx6:
PCI: imx6: Clear CLKREQ# override if 'supports-clkreq' DT property is available
PCI: imx6: Add CLKREQ# override to enable REFCLK for i.MX95 PCIe
PCI: dwc: Invoke post_init in dw_pcie_resume_noirq()
PCI: imx6: Add external reference clock input mode support
dt-bindings: PCI: pci-imx6: Add external reference clock input
dt-bindings: PCI: dwc: Add external reference clock input
|
|
- Add ASPEED Root Complex DT binding and driver (Jacky Chou)
* pci/controller/aspeed:
MAINTAINERS: Add ASPEED PCIe RC driver
PCI: aspeed: Add ASPEED PCIe RC driver
PCI: Add FMT, TYPE and CPL status definition for TLP header
dt-bindings: PCI: Add ASPEED PCIe RC support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. It became a bit larger than wished, but
all of them are device-specific small fixes, and it should be still
fairly safe to take at the last minute.
Included are a few quirks and fixes for Intel, AMD, HD-audio, and
USB-audio, as well as a race fix in aloop driver and corrections of
Cirrus firmware kunit test"
* tag 'sound-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable headset mic for Acer Nitro 5
ASoC: fsl_xcvr: fix missing lock in fsl_xcvr_mode_put()
ASoC: dt-bindings: ti,tlv320aic3x: Add compatible string ti,tlv320aic23
ASoC: amd: fix memory leak in acp3x pdm dma ops
ALSA: usb-audio: fix broken logic in snd_audigy2nx_led_update()
ALSA: aloop: Fix racy access at PCM trigger
ASoC: rt1320: fix intermittent no-sound issue
ASoC: SOF: Intel: use hdev->info.link_mask directly
firmware: cs_dsp: rate-limit log messages in KUnit builds
ASoC: amd: yc: Add quirk for HP 200 G2a 16
ASoC: cs42l43: Correct handling of 3-pole jack load detection
ASoC: Intel: sof_es8336: Add DMI quirk for Huawei BOD-WXX9
ASoC: sof_sdw: Add a quirk for Lenovo laptop using sidecar amps with cs42l43
|
|
Add new compatible string 'fsl,imx952-asrc' for i.MX952 platform,
below are the differences that make this ASRC not fallback compatible
with other platforms.
1) There is a power domain on i.MX952 for the wakeupmix system where
ASRC is in. But it is enabled by default, ASRC device don't need
to enable it, so it is optional for i.MX952.
2) The clock sources of ASRC are different on i.MX952.
3) There is a limitation on i.MX952 that DMA request is not cleared at the
end of conversion with dma slave mode. Which causes sample is dropped from
the input fifo on the second time if DMA is triggered before the client
device and DMA may copy wrong data from output fifo as the output fifo is
not ready in the beginning. So there is specially handling in the driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20260206014805.3897764-2-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from "Miquel Raynal (Schneider Electric)" <miquel.raynal@bootlin.com>:
This series adds support for the QSPI controller available on Renesas
RZ/N1S and RZ/N1D SoC. It has been tested with a custom board (see last
SPI patch for details), but has been tested by Wolfram (thank you!) on
the DB board.
Link: https://lore.kernel.org/linux-devicetree/20260116114852.52948-2-wsa+renesas@sang-engineering.com/
Adding support for this SoC required a few adaptations to the Cadence
QSPI driver which have already been merged (except one regarding clocks
handling). This series contains the remaining patches, the ones actually
adding support for the RZ/N1 flavour.
|
|
Add support for the Renesas RZ/N1D400 QSPI controller.
This SoC is identified in the bindings with its other name: r9a06g032.
It is part of the RZ/N1 family, which contains a "D" and a "S"
variant. IPs in this SoC are typically described using 2 compatibles:
the SoC specific compatible and the family compatible. The original
Cadence IP compatible is dropped because it is unusable on its own.
Indirect accesses are not supported by this flavour of the Cadence IP,
which means several properties have no meaning in the scope of the
Renesas compatible. Let's make sure they are no longer expected nor
mandatory.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal (Schneider Electric) <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260205-schneider-6-19-rc1-qspi-v5-1-843632b3c674@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.19-rc9).
No adjacent changes, conflicts:
drivers/net/ethernet/spacemit/k1_emac.c
3125fc1701694 ("net: spacemit: k1-emac: fix jumbo frame support")
f66086798f91f ("net: spacemit: Remove broken flow control support")
https://lore.kernel.org/aYIysFIE9ooavWia@sirena.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Document the Renesas USBHS controller found on the Renesas RZ/G3E SoC.
The USBHS block on RZ/G3E is functionally identical to the one found
on the RZ/G2L family, so no driver changes are needed. The existing
"renesas,rzg2l-usbhs" fallback compatible will continue to be used for
handling this IP.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260129165412.557643-1-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Some more changes, including pulls from drivers:
- ath drivers: small features/cleanups
- rtw drivers: mostly refactoring for rtw89 RTL8922DE support
- mac80211: use hrtimers for CAC to avoid too long delays
- cfg80211/mac80211: some initial UHR (Wi-Fi 8) support
* tag 'wireless-next-2026-02-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (59 commits)
wifi: brcmsmac: phy: Remove unreachable error handling code
wifi: mac80211: Add eMLSR/eMLMR action frame parsing support
wifi: mac80211: add initial UHR support
wifi: cfg80211: add initial UHR support
wifi: ieee80211: add some initial UHR definitions
wifi: mac80211: use wiphy_hrtimer_work for CAC timeout
wifi: mac80211: correct ieee80211-{s1g/eht}.h include guard comments
wifi: ath12k: clear stale link mapping of ahvif->links_map
wifi: ath12k: Add support TX hardware queue stats
wifi: ath12k: Add support RX PDEV stats
wifi: ath12k: Fix index decrement when array_len is zero
wifi: ath12k: support OBSS PD configuration for AP mode
wifi: ath12k: add WMI support for spatial reuse parameter configuration
dt-bindings: net: wireless: ath11k-pci: deprecate 'firmware-name' property
wifi: ath11k: add usecase firmware handling based on device compatible
wifi: ath10k: sdio: add missing lock protection in ath10k_sdio_fw_crashed_dump()
wifi: ath10k: fix lock protection in ath10k_wmi_event_peer_sta_ps_state_chg()
wifi: ath10k: snoc: support powering on the device via pwrseq
wifi: rtw89: pci: warn if SPS OCP happens for RTL8922DE
wifi: rtw89: pci: restore LDO setting after device resume
...
====================
Link: https://patch.msgid.link/20260204121143.181112-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clocks
As per the RZ/G3L Hardware manual, CPG_CLKON_ETH register bits{12,13} are
to control the RMII{tx, rx} clocks. Document the rmii{tx.rx} clocks for
RZ/G3L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260203104541.264759-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The S32 chipsets have a GPR region which has a miscellaneous registers
including the GMAC_0_CTRL_STS register. Originally, this code accessed
that register in a sort of ad-hoc way, but it's cleaner to use a
syscon interface to access these registers.
We still need to maintain the old method of accessing the GMAC register
but using a syscon will let us access other registers more cleanly.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/3b75e950b2f8faecd1a9fa757e7eb7b42ace838f.1769764941.git.dan.carpenter@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge series from Sen Wang <sen@ti.com>:
This series adds asynchronous mode support to the McASP driver, which
enables independent configuration of bitclocks, frame sync, and audio
configurations between tx(playback) and rx(record). And achieves
simultaneous playback & record using different audio configurations.
It also adds two clean up patches to the McASP driver that disambiguate
and simplifies the logic which avoids the async enhancement from being
too convoluted to review and analyze.
The implementation is based on vendor documentation and patches tested in
both SK-AM62P-LP (sync mode, McASP slave) and AM62D-EVM
(async mode, McASP master, rx & tx has different TDM configs).
Testing verifies async mode functionality while maintaining backward
compatibility with the default sync mode.
Bootlog and Async mode tests on AM62D-EVM: [0]
[0]: https://gist.github.com/SenWang125/f31f9172b186d414695e37c8b9ef127d
|
|
Merge series from André Draszik <andre.draszik@linaro.org>:
This series extends the existing S2MPG10 PMIC driver to add support for
the regulators, and adds new S2MPG11 core and regulator drivers.
The patches are kept together in one series, due to S2MPG11 and its
regulators being very similar to S2MPG10.
The Samsung S2MPG11 PMIC is a Power Management IC for mobile
applications with buck converters, various LDOs, power meters, and
additional GPIO interfaces. It typically complements an S2MPG10 PMIC in
a main/sub configuration as the sub-PMIC and both are used on the
Google Pixel 6 and 6 Pro (oriole / raven).
A DT update for Oriole / Raven to enable these is required which I will
send out separately.
|
|
McASP supports the independent configuration of TX & RX clk and frame
sync registers. By default, the driver is configured in synchronous mode
where RX clock generator is disabled and it uses transmit clock signals as
bit clock and frame sync. Therefore add optional properties needed for
asynchronous mode.
Add ti,async-mode boolean binding to provide a way to decouple the default
behavior and allows for independent TX & RX clocking.
Add tdm-slots-rx uint32 binding to provide an alternative hardware
specifier stating the number of RX serializers.
The existing property tdm-slots will still dictate number of
TX serializers, and RX if tdm-slots-rx isn't given for backwards
compatibility.
Add auxclk-fs-ratio-rx which allows to specify the ratio just for RX.
The driver can be supplied with two different ratios
(auxclk-fs-ratio and auxclk-fs-ratio-rx in tandem) and achieve two
different sampling rates for tx & rx.
Signed-off-by: Sen Wang <sen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Paresh Bhagat <p-bhagat@ti.com>
Link: https://patch.msgid.link/20260203003703.2334443-2-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update interrupt maxItems to 16 from 13 per GPI instance to support
Glymur, Qualcomm's latest gen SoC
Signed-off-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251231133114.2752822-1-pankaj.patil@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The three instances of CCI found on the QCS8300 are functionally the same
as on a number of existing Qualcomm SoCs.
Introduce a new SoC-specific compatible string "qcom,qcs8300-cci" with a
common fallback.
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum@quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260121183142.1867199-2-quic_nihalkum@quicinc.com
|
|
Convert TI OMAP Control PHY binding to DT schema.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
Link: https://patch.msgid.link/20260123-ti-phy-v4-3-b557e2c46e6f@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert TI PIPE3 PHY binding to DT schema.
Changes during conversion:
- Define a new pattern 'pcie-phy' to match nodes defined in DT.
- Drop obsolete "id" property from the schema.
Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260123-ti-phy-v4-2-b557e2c46e6f@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add compatible string "fsl,imx952-rpmsg-audio" for i.MX952 platform,
which is backward compatible with i.MX95. Set it to fall back to
"fsl,imx95-rpmsg-audio".
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20260202105622.39772-3-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add compatible string "fsl,imx94-rpmsg-audio" for i.MX94 platform,
which is backward compatible with i.MX95. Set it to fall back to
"fsl,imx95-rpmsg-audio".
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://patch.msgid.link/20260202105622.39772-2-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The S2MPG11 PMIC is a Power Management IC for mobile applications with
buck converters, various LDOs, power meters, NTC thermistor inputs, and
additional GPIO interfaces. It typically complements an S2MPG10 PMIC in
a main/sub configuration as the sub-PMIC.
S2MPG11 has 12 buck, 1 buck-boost, and 15 LDO rails. Several of these
can either be controlled via software (register writes) or via external
signals, in particular by:
* one out of several input pins connected to a main processor's:
* GPIO pins
* other pins that are e.g. firmware- or power-domain-controlled
without explicit driver intervention
* a combination of input pins and register writes.
Control via input pins allows PMIC rails to be controlled by firmware,
e.g. during standby/suspend, or as part of power domain handling where
otherwise that would not be possible. Additionally toggling a pin is
faster than register writes, and it also allows the PMIC to ensure that
any necessary timing requirements between rails are respected
automatically if multiple rails are to be enabled or disabled quasi
simultaneously.
While external control via input pins appears to exist on other
versions of this PMIC, there is more flexibility in this version, in
particular there is a selection of input pins to choose from for each
rail (which must therefore be configured accordingly if in use),
whereas other versions don't have this flexibility.
Add documentation related to the regulator (buck & ldo) parts like
devicetree definitions, regulator naming patterns, and additional
properties.
Since S2MPG11 is typically used as the sub-PMIC together with an
S2MPG10 as the main-PMIC, the datasheet and the binding both suffix the
rails with an 's'.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-3-3b1f9831fffd@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The S2MPG10 PMIC is a Power Management IC for mobile applications with
buck converters, various LDOs, power meters, RTC, clock outputs, and
additional GPIO interfaces.
It has 10 buck and 31 LDO rails. Several of these can either be
controlled via software (register writes) or via external signals, in
particular by:
* one out of several input pins connected to a main processor's:
* GPIO pins
* other pins that are e.g. firmware- or power-domain-controlled
without explicit driver intervention
* a combination of input pins and register writes.
Control via input pins allows PMIC rails to be controlled by firmware,
e.g. during standby/suspend, or as part of power domain handling where
otherwise that would not be possible. Additionally toggling a pin is
faster than register writes, and it also allows the PMIC to ensure that
any necessary timing requirements between rails are respected
automatically if multiple rails are to be enabled or disabled quasi
simultaneously.
While external control via input pins appears to exist on other
versions of this PMIC, there is more flexibility in this version, in
particular there is a selection of input pins to choose from for each
rail (which must therefore be configured accordingly if in use),
whereas other versions don't have this flexibility.
Add documentation related to the regulator (buck & ldo) parts like
devicetree definitions, regulator naming patterns, and additional
properties.
S2MPG10 is typically used as the main-PMIC together with an S2MPG11
PMIC in a main/sub configuration, hence the datasheet and the binding
both suffix the rails with an 'm'.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-2-3b1f9831fffd@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using lowercase for the buck and ldo nodenames is preferred, as
evidenced e.g. in [1].
Convert the example here to lowercase before we add any bindings
describing the s2mpg1x regulators that will enforce the spelling.
Link: https://lore.kernel.org/all/20250223-mysterious-infrared-civet-e5bcbf@krzk-bin/ [1]
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-1-3b1f9831fffd@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The simple audio codec bindings were consolidated into
trivial-codec.yaml by commit 4acbfcf11cbe ("ASoC: dt-bindings:
consolidate simple audio codec to trivial-codec.yaml").
Update the DA9055 binding documentation to reference the new
trivial-codec.yaml location.
Signed-off-by: Soham Metha <sohammetha01@gmail.com>
Link: https://patch.msgid.link/20260126111309.22097-1-sohammetha01@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add compatible string ti,tlv320aic23 to fix below CHECK_DTB warning:
arch/arm/boot/dts/nxp/imx/imx35-eukrea-mbimxsd35-baseboard.dtb:
/soc/bus@43f00000/i2c@43f80000/codec@1a: failed to match any schema with compatible: ['ti,tlv320aic23']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20260202205758.3044617-1-Frank.Li@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Imagis IST3038 provides touch keys. Allow linux,keycodes for ist3038.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251224100941.3356201-1-raymondhackley@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Convert the TI LM3697 LED driver binding to DT schema format. It's a
straight-forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260121235746.370607-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The Samsung S2MPG11 PMIC is similar to the existing S2MPG10 PMIC
supported by this binding, but still differs enough from it to justify
a separate binding.
It is a Power Management IC for mobile applications with buck
converters, various LDOs, power meters, NTC thermistor inputs, and
additional GPIO interfaces and typically complements an S2MPG10 PMIC in
a main/sub configuration as the sub-PMIC.
Like S2MPG10, communication is via the Samsung ACPM firmware and it
therefore needs to be a child of the ACPM firmware node.
Add the PMIC, the regulators node, and the supply inputs of the
regulator rails, with the supply names matching the datasheet.
Note: S2MPG11 is typically used as the sub-PMIC together with an
S2MPG10 PMIC in a main/sub configuration, hence the datasheet and the
binding both suffix the supplies with an 's'.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-6-3b1f9831fffd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Update the regulators node to link to the correct and expected
samsung,s2mpg10-regulators binding, in order to describe the regulators
available on this PMIC.
Additionally, describe the supply inputs of the regulator rails, with
the supply names matching the datasheet.
While at it, update the description and example slightly.
Note: S2MPG10 is typically used as the main-PMIC together with an
S2MPG11 PMIC in a main/sub configuration, hence the datasheet and the
binding both suffix the supplies with an 'm'.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-5-3b1f9831fffd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The samsung,s2mpg10-pmic binding is going to acquire various additional
properties. To avoid making the common samsung,s2mps11 binding file too
complicated due to additional nesting, split s2mpg10 out into its own
file.
As a side-effect, the oneOf for the interrupts is not required anymore,
as the required: node is at the top-level now.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260122-s2mpg1x-regulators-v7-4-3b1f9831fffd@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Document ovp values supported by wled found in PMI8950.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org>
Link: https://patch.msgid.link/20260116-pmi8950-wled-v3-3-e6c93de84079@mainlining.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Document ovp values supported by wled found in PMI8994.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org>
Link: https://patch.msgid.link/20260116-pmi8950-wled-v3-1-e6c93de84079@mainlining.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
meaning in PLIC
In PLIC, interrupt source 0 is reserved and should not be used.
Therefore, the valid interrupt sources are from 1 to riscv,ndev
inclusive.
Update the documentation to clarify this point.
[ tglx: Fixup subject prefix ]
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/tencent_720A4669773B1EE15EC720869C35C2F0490A@qq.com
|
|
The bindings are incomplete, as the GPIO/Audio Input pin
is still undocumented. The hardware used for testing this patch series
does not allow modification, so the mentioned pin has been omitted.
Signed-off-by: Lukas Timmermann <linux@timmermann.space>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260118165010.902086-2-linux@timmermann.space
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Document compatible for PMH0101 Torch and Flash LED controller.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Signed-off-by: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-knp-pmic-leds-v3-2-5e583f68b0e5@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for PMH0101 PWM modules which are compatible with the PM8350c
PWM modules.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Signed-off-by: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-knp-pmic-leds-v3-1-5e583f68b0e5@oss.qualcomm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
In some cases, for example when using multiple instances of
leds-group-multicolor, a board may have multiple multi-leds which can't
be distinguished by unit address. In such cases it should be possible to
name them differently, for example multi-led-0 and multi-led-1. This
patch adds another node name pattern to leds-class-multicolor.yaml to
allow such names.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20260101-multi-led-v3-1-e29ca8dedd37@posteo.net
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The LP5812 is a 4x3 RGB LED driver with an autonomous animation
engine and time-cross-multiplexing (TCM) support for up to 12 LEDs
or 4 RGB LEDs. It supports both analog (256 levels) and PWM (8-bit)
dimming, including exponential PWM for smooth brightness control.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Nam Tran <trannamatk@gmail.com>
Link: https://patch.msgid.link/20251221041950.4631-2-trannamatk@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
This variant supports 3 channels with 4096 brightness steps.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20251219154521.643312-2-daniel@zonque.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chleroy/linux into soc/drivers
FSL SOC Changes for 6.20
Freescale Management Complex:
- Convert fsl-mc bus to bus callbacks
- Fix a use-after-free
- Drop redundant error messages
- Fix ressources release on some error path
Freescale QUICC Engine:
- Add an interrupt controller for IO Ports
- Use scoped for-each OF child loop
* tag 'soc_fsl-6.20-1' of https://git.kernel.org/pub/scm/linux/kernel/git/chleroy/linux:
bus: fsl-mc: fix an error handling in fsl_mc_device_add()
soc: fsl: qe: qe_ports_ic: Consolidate chained IRQ handler install/remove
dt-bindings: soc: fsl: qe: Add an interrupt controller for QUICC Engine Ports
soc: fsl: qe: Add an interrupt controller for QUICC Engine Ports
soc: fsl: qe: Simplify with scoped for each OF child loop
bus: fsl-mc: fix use-after-free in driver_override_show()
bus: fsl-mc: Convert to bus callbacks
bus: fsl-mc: Drop error message in probe function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt
SoCFPGA DTS updates for v6.20, version 3
- dt-bindings updates:
- Add intel,socfpga-agilex5-socdk-modular for the Agilex5 mod board
- Add intel,socfpga-agilex-emmc for the Agilex eMMC daughter board
- Move entries in intel,socfpga.yaml into altera.yaml
- Add syscon as a fallback for sys-mgr
- Add dma-cohrerent property for Agilex5 NAND and DMA
- Add support for the Agilex5 modular board
- Add IOMMUS property for ethernet nodes for Agilex5
- Use lowercase hex for dts files
- Add #address-cells and #size-cells for sram
- Fix dtbs_check warning for fpga-region
- Move dma controller node for Agilex5 under simple-bus
- Add support for the Agilex eMMC daughter board
* tag 'socfpga_dts_updates_for_v6.20_v3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
dt-bindings: intel: Add Agilex eMMC support
arm64: dts: socfpga: agilex: add emmc support
arm64: dts: intel: agilex5: Add simple-bus node on top of dma controller node
ARM: dts: socfpga: fix dtbs_check warning for fpga-region
ARM: dts: socfpga: add #address-cells and #size-cells for sram node
dt-bindings: altera: document syscon as fallback for sys-mgr
arm64: dts: altera: Use lowercase hex
dt-bindings: arm: altera: combine Intel's SoCFPGA into altera.yaml
arm64: dts: socfpga: agilex5: Add IOMMUS property for ethernet nodes
arm64: dts: socfpga: agilex5: add support for modular board
dt-bindings: intel: Add Agilex5 SoCFPGA modular board
arm64: dts: socfpga: agilex5: Add dma-coherent property
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The SCU MU driver has already supported the simple and efficient single-TX
and single-RX channel layout since 2021. The older multi-channel MU
configurations (tx0..tx3 and rx0..rx3) are less efficient in practice and
not needed.
Mark these legacy mbox-names and mboxes tuple layouts as deprecated in the
binding schema. The driver continues to support them for backward
compatibility in case firmware publishes the legacy properties.
The example section is updated accordingly to demonstrate the recommended
layout.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260127-scu-v2-1-03f3aaa56e1b@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Fix email addresses with spaces or missing brackets. A pending
dtschema meta-schema change will check for these.
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20260126164724.2832009-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
