| Age | Commit message (Collapse) | Author |
|---|
|
An incorrect device name was logged for PCA9452 because the dev_info()
ternary omitted PCA9452 and fell through to "pca9450bc". Introduce a
type_name and set it per device type so the probed message matches the
actual PMIC. While here, make the PCA9451A case explicit.
No functional changes.
Fixes: 017b76fb8e5b6 ("regulator: pca9450: Add PMIC pca9452 support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20260310-pca9450-irq-v1-2-36adf52c2c55@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kernel warning on i.MX8MP-EVK when doing module test:
irq: type mismatch, failed to map hwirq-3 for gpio@30200000!
Per PCA945[X] specification: The IRQ_B pin is pulled low when any unmasked
interrupt bit status is changed and it is released high once application
processor read INT1 register.
So the interrupt should be configured as IRQF_TRIGGER_LOW, not
IRQF_TRIGGER_FALLING.
Fixes: 0935ff5f1f0a4 ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20260310-pca9450-irq-v1-1-36adf52c2c55@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The move of the AHB and APB clocks from a JH7110 specific quirk to the
main clock init dropped the specification of the clock names to request
for the AHB and APB clocks, resulting in the clock framework requesting
a clock with a NULL name three times. On most platforms where the
clocks are physically the same or some are always on this makes no
difference but the reason we had the specific quirk for JH7110 is that
it does actually have separate, controllable clocks. Update the new
code to request the AHB and APB clocks by name to restore the original
behaviour on JH7110.
Fixes: 324ecc7788c2 ("spi: cadence-qspi: Kill cqspi_jh7110_clk_init")
Reported-by: Ron Economos <re@w6rz.net>
Closes: https://lore.kernel.org/r/a3ca5e9b-7446-497e-8df2-7ef2b42a02e9@w6rz.net
Tested-by: Ron Economos <re@w6rz.net>
Link: https://patch.msgid.link/20260307-spi-cadence-qspi-fix-jh7110-v1-1-c9f37b8c58b1@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20260307-spi-cadence-qspi-fix-jh7110-v1-1-c9f37b8c58b1@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2026-03-10
this is a pull request of 2 patches for net/main.
Haibo Chen's patch fixes the maximum allowed bit rate error, which was
broken in v6.19.
Wenyuan Li contributes a patch for the hi311x driver that adds missing
error checking in the caller of the hi3110_power_enable() function,
hi3110_open().
linux-can-fixes-for-7.0-20260310
* tag 'linux-can-fixes-for-7.0-20260310' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: hi311x: hi3110_open(): add check for hi3110_power_enable() return value
can: dev: keep the max bitrate error at 5%
====================
Link: https://patch.msgid.link/20260310103547.2299403-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 02c057ddefef ("ACPI: video: Convert the driver to a platform one")
switched over the ACPI video bus driver from an ACPI driver to a platform
driver, but that change introduced an unwanted and unexpected side effect.
Namely, on some systems, the ACPI device object of the ACPI video bus
device is an ACPI companion of multiple platform devices and, after
adding video_device_ids[] as an acpi_match_table to the acpi_video_bus
platform driver, all of those devices started to match that driver and
its probe callback is invoked for all of them (it fails, but it leaves
a confusing message in the log). Moreover, the MODULE_DEVICE_TABLE()
of the ACPI video driver module matches all of the devices sharing the
ACPI companion with the ACPI video bus device.
To address this, make the core ACPI device enumeration code create an
auxiliary device for the ACPI video bus device object instead of a
platform device and switch over the ACPI video bus driver (once more)
to an auxiliary driver.
Auxiliary driver generally is a better match for ACPI video bus than
platform driver, among other things because the ACPI video bus device
does not require any resources to be allocated for it during
enumeration. It also allows the ACPI video bus driver to stop abusing
device matching based on ACPI device IDs and it allows a special case
to be dropped from acpi_create_platform_device() because that function
need not worry about the ACPI video bus device any more.
Fixes: 02c057ddefef ("ACPI: video: Convert the driver to a platform one")
Reported-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Closes: https://lore.kernel.org/linux-acpi/007e3390-6b2b-457e-83c7-c794c5952018@amd.com/
Tested-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
[ rjw: Added AUXILIARY_BUS selection to CONFIG_ACPI to fix build issue ]
[ rjw: Fixed error path in acpi_create_video_bus_device() ]
Link: https://patch.msgid.link/5986516.DvuYhMxLoT@rafael.j.wysocki
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The hashmap__new() function never returns NULL, it returns error
pointers. Fix the error checking to match.
Additionally, set src->samples to NULL to prevent any later code from
accidentally using the error pointer.
Fixes: d3e7cad6f36d9e80 ("perf annotate: Add a hashmap for symbol histogram")
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tianyou Li <tianyou.li@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
IDLETIMER revision 0 rules reuse existing timers by label and always call
mod_timer() on timer->timer.
If the label was created first by revision 1 with XT_IDLETIMER_ALARM,
the object uses alarm timer semantics and timer->timer is never initialized.
Reusing that object from revision 0 causes mod_timer() on an uninitialized
timer_list, triggering debugobjects warnings and possible panic when
panic_on_warn=1.
Fix this by rejecting revision 0 rule insertion when an existing timer with
the same label is of ALARM type.
Fixes: 68983a354a65 ("netfilter: xtables: Add snapshot of hardidletimer target")
Co-developed-by: Yifan Wu <yifanwucs@gmail.com>
Signed-off-by: Yifan Wu <yifanwucs@gmail.com>
Co-developed-by: Juefei Pu <tomapufckgml@gmail.com>
Signed-off-by: Juefei Pu <tomapufckgml@gmail.com>
Signed-off-by: Yuan Tan <tanyuan98@outlook.com>
Signed-off-by: Xin Liu <dstsmallbird@foxmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
nfnl_cthelper_dump_table() has a 'goto restart' that jumps to a label
inside the for loop body. When the "last" helper saved in cb->args[1]
is deleted between dump rounds, every entry fails the (cur != last)
check, so cb->args[1] is never cleared. The for loop finishes with
cb->args[0] == nf_ct_helper_hsize, and the 'goto restart' jumps back
into the loop body bypassing the bounds check, causing an 8-byte
out-of-bounds read on nf_ct_helper_hash[nf_ct_helper_hsize].
The 'goto restart' block was meant to re-traverse the current bucket
when "last" is no longer found, but it was placed after the for loop
instead of inside it. Move the block into the for loop body so that
the restart only occurs while cb->args[0] is still within bounds.
BUG: KASAN: slab-out-of-bounds in nfnl_cthelper_dump_table+0x9f/0x1b0
Read of size 8 at addr ffff888104ca3000 by task poc_cthelper/131
Call Trace:
nfnl_cthelper_dump_table+0x9f/0x1b0
netlink_dump+0x333/0x880
netlink_recvmsg+0x3e2/0x4b0
sock_recvmsg+0xde/0xf0
__sys_recvfrom+0x150/0x200
__x64_sys_recvfrom+0x76/0x90
do_syscall_64+0xc3/0x6e0
Allocated by task 1:
__kvmalloc_node_noprof+0x21b/0x700
nf_ct_alloc_hashtable+0x65/0xd0
nf_conntrack_helper_init+0x21/0x60
nf_conntrack_init_start+0x18d/0x300
nf_conntrack_standalone_init+0x12/0xc0
Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
nfqnl_recv_verdict() calls find_dequeue_entry() to remove the queue
entry from the queue data structures, taking ownership of the entry.
For PF_BRIDGE packets, it then calls nfqa_parse_bridge() to parse VLAN
attributes. If nfqa_parse_bridge() returns an error (e.g. NFQA_VLAN
present but NFQA_VLAN_TCI missing), the function returns immediately
without freeing the dequeued entry or its sk_buff.
This leaks the nf_queue_entry, its associated sk_buff, and all held
references (net_device refcounts, struct net refcount). Repeated
triggering exhausts kernel memory.
Fix this by dropping the entry via nfqnl_reinject() with NF_DROP verdict
on the error path, consistent with other error handling in this file.
Fixes: 8d45ff22f1b4 ("netfilter: bridge: nf queue verdict to use NFQA_VLAN and NFQA_L2HDR")
Reviewed-by: David Dull <monderasdor@gmail.com>
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When the last byte of options is a non-single-byte option kind, walkers
that advance with i += op[i + 1] ? : 1 can read op[i + 1] past the end
of the option area.
Add an explicit i == optlen - 1 check before dereferencing op[i + 1]
in xt_tcpudp and xt_dccp option walkers.
Fixes: 2e4e6a17af35 ("[NETFILTER] x_tables: Abstraction layer for {ip,ip6,arp}_tables")
Signed-off-by: David Dull <monderasdor@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
pipapo_drop() passes rulemap[i + 1].n to pipapo_unmap() as the
to_offset argument on every iteration, including the last one where
i == m->field_count - 1. This reads one element past the end of the
stack-allocated rulemap array (declared as rulemap[NFT_PIPAPO_MAX_FIELDS]
with NFT_PIPAPO_MAX_FIELDS == 16).
Although pipapo_unmap() returns early when is_last is true without
using the to_offset value, the argument is evaluated at the call site
before the function body executes, making this a genuine out-of-bounds
stack read confirmed by KASAN:
BUG: KASAN: stack-out-of-bounds in pipapo_drop+0x50c/0x57c [nf_tables]
Read of size 4 at addr ffff8000810e71a4
This frame has 1 object:
[32, 160) 'rulemap'
The buggy address is at offset 164 -- exactly 4 bytes past the end
of the rulemap array.
Pass 0 instead of rulemap[i + 1].n on the last iteration to avoid
the out-of-bounds read.
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Signed-off-by: Jenny Guanni Qu <qguanni@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..]
Fixes: 628bd3e49cba ("netfilter: nf_tables: drop map element references from preparation phase")
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When handling NETDEV_REGISTER notification, duplicate device
registration must be avoided since the device may have been added by
nft_netdev_hook_alloc() already when creating the hook.
Suggested-by: Florian Westphal <fw@strlen.de>
Reported-by: syzbot+bb9127e278fa198e110c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bb9127e278fa198e110c
Fixes: a331b78a5525 ("netfilter: nf_tables: Respect NETDEV_REGISTER events")
Tested-by: Helen Koike <koike@igalia.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Update the header to pull in the changes from commit 3285c471d0c0b991
("coresight: Remove misleading definitions").
Signed-off-by: James Clark <james.clark@linaro.org>
Requested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Leo Yan <leo.yan@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/557db631-aef8-43b1-9f45-fae75910ccb4@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
These #defines have been removed from the kernel headers in favour of
the string based PMU format attributes. Usages were previously removed
from the recording side of cs-etm in Perf. Finish the removal by
removing usages from the decode side too.
It's a straight replacement of the old #defines with the new register
bit definitions. Except cs_etm__setup_timeless_decoding() which wasn't
looking at the saved metadata and was instead hard coding an access to
'attr.config'. This was vulnerable to the same issue of .config being
moved to .config2 etc that the original removal of ETM_OPT_* tried to
fix. So fix that too.
Signed-off-by: James Clark <james.clark@linaro.org>
Tested-by: Leo Yan <leo.yan@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The NPU 60XX uses the default boot params location specified
in the firmware image header, consistent with earlier generations.
Remove the unnecessary MMIO register write, freeing the AON register
for future use.
Fixes: 44e4c88951fa ("accel/ivpu: Implement warm boot flow for NPU6 and unify boot handling")
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Link: https://patch.msgid.link/20260305142226.194995-1-andrzej.kacprowski@linux.intel.com
(cherry picked from commit 81e62e7bf8b9309bf0febdf00940818f98bc23d8)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Tunnel xmit functions (iptunnel_xmit, ip6tunnel_xmit) lack their own
recursion limit. When a bond device in broadcast mode has GRE tap
interfaces as slaves, and those GRE tunnels route back through the
bond, multicast/broadcast traffic triggers infinite recursion between
bond_xmit_broadcast() and ip_tunnel_xmit()/ip6_tnl_xmit(), causing
kernel stack overflow.
The existing XMIT_RECURSION_LIMIT (8) in the no-qdisc path is not
sufficient because tunnel recursion involves route lookups and full IP
output, consuming much more stack per level. Use a lower limit of 4
(IP_TUNNEL_RECURSION_LIMIT) to prevent overflow.
Add recursion detection using dev_xmit_recursion helpers directly in
iptunnel_xmit() and ip6tunnel_xmit() to cover all IPv4/IPv6 tunnel
paths including UDP encapsulated tunnels (VXLAN, Geneve, etc.).
Move dev_xmit_recursion helpers from net/core/dev.h to public header
include/linux/netdevice.h so they can be used by tunnel code.
BUG: KASAN: stack-out-of-bounds in blake2s.constprop.0+0xe7/0x160
Write of size 32 at addr ffff88810033fed0 by task kworker/0:1/11
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
__build_flow_key.constprop.0 (net/ipv4/route.c:515)
ip_rt_update_pmtu (net/ipv4/route.c:1073)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:84)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
mld_sendpack
mld_ifc_work
process_one_work
worker_thread
</TASK>
Fixes: 745e20f1b626 ("net: add a recursion limit in xmit path")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Link: https://patch.msgid.link/20260306160133.3852900-2-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
My easystack email will be unreachable soon, update my email address to
linux.dev one.
Signed-off-by: Dongsheng Yang <dongsheng.yang@linux.dev>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
While head_onwire_len() has a branch to handle ctrl_len == 0 case,
prepare_read_control() always sets up a kvec for the CRC meaning that
a non-empty control segment is effectively assumed. All frames that
clients deal with meet that assumption, so let's make it official and
treat the preamble with an empty control segment as malformed.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
|
|
Similar checks are performed for all control frames, but an early check
for message frames was missing. process_message() is already set up to
terminate the loop in case the state changes while con->ops->dispatch()
handler is being executed.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
Reviewed-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
|
|
If the message frame is (maliciously) corrupted in a way that the
length of the control segment ends up being less than the size of the
message header or a different frame is made to look like a message
frame, out-of-bounds reads may ensue in process_message_header().
Perform an explicit bounds check before decoding the message header.
Cc: stable@vger.kernel.org
Reported-by: Raphael Zimmer <raphael.zimmer@tu-ilmenau.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
Reviewed-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
|
|
Raju Rangoju says:
====================
amd-xgbe: RX adaptation and PHY handling fixes
This series fixes several issues in the amd-xgbe driver related to RX
adaptation and PHY handling in 10GBASE-KR mode, particularly when
auto-negotiation is disabled.
Patch 1 fixes link status handling during RX adaptation by correctly
reading the latched link status bit so transient link drops are
detected without losing the current state.
Patch 2 prevents CRC errors that can occur when performing RX
adaptation with auto-negotiation turned off. The driver now stops
TX/RX before re-triggering RX adaptation and only re-enables traffic
once adaptation completes and the link is confirmed up, ensuring
packets are not corrupted during the adaptation window.
Patch 3 restores the intended ordering of PHY reset relative to
phy_start(), making sure PHY settings are reset before the PHY is
started instead of afterwards.
====================
Link: https://patch.msgid.link/20260306111629.1515676-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
commit f93505f35745 ("amd-xgbe: let the MAC manage PHY PM") moved
xgbe_phy_reset() from xgbe_open() to xgbe_start(), placing it after
phy_start(). As a result, the PHY settings were being reset after the
PHY had already started.
Reorder the calls so that the PHY settings are reset before
phy_start() is invoked.
Fixes: f93505f35745 ("amd-xgbe: let the MAC manage PHY PM")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-4-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When operating in 10GBASE-KR mode with auto-negotiation disabled and RX
adaptation enabled, CRC errors can occur during the RX adaptation
process. This happens because the driver continues transmitting and
receiving packets while adaptation is in progress.
Fix this by stopping TX/RX immediately when the link goes down and RX
adaptation needs to be re-triggered, and only re-enabling TX/RX after
adaptation completes and the link is confirmed up. Introduce a flag to
track whether TX/RX was disabled for adaptation so it can be restored
correctly.
This prevents packets from being transmitted or received during the RX
adaptation window and avoids CRC errors from corrupted frames.
The flag tracking the data path state is synchronized with hardware
state in xgbe_start() to prevent stale state after device restarts.
This ensures that after a restart cycle (where xgbe_stop disables
TX/RX and xgbe_start re-enables them), the flag correctly reflects
that the data path is active.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-3-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The link status bit is latched low to allow detection of momentary
link drops. If the status indicates that the link is already down,
read it again to obtain the current state.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-2-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When resuming from s2ram, firmware may re-enable x2apic mode, which may have
been disabled by the kernel during boot either because it doesn't support IRQ
remapping or for other reasons. This causes the kernel to continue using the
xapic interface, while the hardware is in x2apic mode, which causes hangs.
This happens on defconfig + bare metal + s2ram.
Fix this in lapic_resume() by disabling x2apic if the kernel expects it to be
disabled, i.e. when x2apic_mode = 0.
The ACPI v6.6 spec, Section 16.3 [1] says firmware restores either the
pre-sleep configuration or initial boot configuration for each CPU, including
MSR state:
When executing from the power-on reset vector as a result of waking from an
S2 or S3 sleep state, the platform firmware performs only the hardware
initialization required to restore the system to either the state the
platform was in prior to the initial operating system boot, or to the
pre-sleep configuration state. In multiprocessor systems, non-boot
processors should be placed in the same state as prior to the initial
operating system boot.
(further ahead)
If this is an S2 or S3 wake, then the platform runtime firmware restores
minimum context of the system before jumping to the waking vector. This
includes:
CPU configuration. Platform runtime firmware restores the pre-sleep
configuration or initial boot configuration of each CPU (MSR, MTRR,
firmware update, SMBase, and so on). Interrupts must be disabled (for
IA-32 processors, disabled by CLI instruction).
(and other things)
So at least as per the spec, re-enablement of x2apic by the firmware is
allowed if "x2apic on" is a part of the initial boot configuration.
[1] https://uefi.org/specs/ACPI/6.6/16_Waking_and_Sleeping.html#initialization
[ bp: Massage. ]
Fixes: 6e1cb38a2aef ("x64, x2apic/intr-remap: add x2apic support, including enabling interrupt-remapping")
Co-developed-by: Rahul Bukte <rahul.bukte@sony.com>
Signed-off-by: Rahul Bukte <rahul.bukte@sony.com>
Signed-off-by: Shashank Balaji <shashank.mahadasyam@sony.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260306-x2apic-fix-v2-1-bee99c12efa3@sony.com
|
|
mctp_flow_prepare_output() checks key->dev and may call
mctp_dev_set_key(), but it does not hold key->lock while doing so.
mctp_dev_set_key() and mctp_dev_release_key() are annotated with
__must_hold(&key->lock), so key->dev access is intended to be
serialized by key->lock. The mctp_sendmsg() transmit path reaches
mctp_flow_prepare_output() via mctp_local_output() -> mctp_dst_output()
without holding key->lock, so the check-and-set sequence is racy.
Example interleaving:
CPU0 CPU1
---- ----
mctp_flow_prepare_output(key, devA)
if (!key->dev) // sees NULL
mctp_flow_prepare_output(
key, devB)
if (!key->dev) // still NULL
mctp_dev_set_key(devB, key)
mctp_dev_hold(devB)
key->dev = devB
mctp_dev_set_key(devA, key)
mctp_dev_hold(devA)
key->dev = devA // overwrites devB
Now both devA and devB references were acquired, but only the final
key->dev value is tracked for release. One reference can be lost,
causing a resource leak as mctp_dev_release_key() would only decrease
the reference on one dev.
Fix by taking key->lock around the key->dev check and
mctp_dev_set_key() call.
Fixes: 67737c457281 ("mctp: Pass flow data & flow release events to drivers")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://patch.msgid.link/20260306031402.857224-1-dg573847474@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1
Fixes: 1284cd3a2b74 ("bonding: two small fixes for IPoIB support")
Suggested-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Link: https://patch.msgid.link/20260306021508.222062-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In hi3110_open(), the return value of hi3110_power_enable() is not checked.
If power enable fails, the device may not function correctly, while the
driver still returns success.
Add a check for the return value and propagate the error accordingly.
Signed-off-by: Wenyuan Li <2063309626@qq.com>
Link: https://patch.msgid.link/tencent_B5E2E7528BB28AA8A2A56E16C49BD58B8B07@qq.com
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
[mkl: adjust subject, commit message and jump label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit b360a13d44db ("can: dev: print bitrate error with two decimal
digits") changed calculation of the bit rate error from on-tenth of a
percent to on-hundredth of a percent, but forgot to adjust the scale of the
CAN_CALC_MAX_ERROR constant.
Keeping the existing logic unchanged: Only when the bitrate error exceeds
5% should an error be returned. Otherwise, simply output a warning log.
Fixes: b360a13d44db ("can: dev: print bitrate error with two decimal digits")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://patch.msgid.link/20260306-can-fix-v1-1-ac526cec6777@nxp.com
Cc: stable@kernel.org
[mkl: improve commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When 'midev->allow_rx' is false, the newly allocated skb isn't consumed
by netif_rx(), it needs to free the skb directly.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Link: https://patch.msgid.link/20260305143240.97592-1-haiyuewa@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
obj_exts_alloc_size() prevents recursive allocation of slabobj_ext
array from the same cache, to avoid creating slabs that are never freed.
There is one mistake that returns the original size when memory
allocation profiling is disabled. The assumption was that
memcg-triggered slabobj_ext allocation is always served from
KMALLOC_CGROUP type. But this is wrong [1]: when the caller specifies
both __GFP_RECLAIMABLE and __GFP_ACCOUNT with SLUB_TINY enabled, the
allocation is served from normal kmalloc. This is because kmalloc_type()
prioritizes __GFP_RECLAIMABLE over __GFP_ACCOUNT, and SLUB_TINY aliases
KMALLOC_RECLAIM with KMALLOC_NORMAL.
As a result, the recursion guard is bypassed and the problematic slabs
can be created. Fix this by removing the mem_alloc_profiling_enabled()
check entirely. The remaining is_kmalloc_normal() check is still
sufficient to detect whether the cache is of KMALLOC_NORMAL type and
avoid bumping the size if it's not.
Without SLUB_TINY, no functional change intended.
With SLUB_TINY, allocations with __GFP_ACCOUNT|__GFP_RECLAIMABLE
now allocate a larger array if the sizes equal.
Reported-by: Zw Tang <shicenci@gmail.com>
Fixes: 280ea9c3154b ("mm/slab: avoid allocating slabobj_ext array from its own slab")
Closes: https://lore.kernel.org/linux-mm/CAPHJ_VKuMKSke8b11AZQw1PTSFN4n2C0gFxC6xGOG0ZLHgPmnA@mail.gmail.com [1]
Cc: stable@vger.kernel.org
Signed-off-by: Harry Yoo <harry.yoo@oracle.com>
Link: https://patch.msgid.link/20260309072219.22653-1-harry.yoo@oracle.com
Tested-by: Zw Tang <shicenci@gmail.com>
Signed-off-by: Vlastimil Babka (SUSE) <vbabka@kernel.org>
|
|
Hotplugging a CPU off and back on fails with pKVM, as we try to
probe for ICH_VTR_EL2.TDS. In a non-VHE setup, this is achieved
by using an EL2 stub helper. However, the stubs are out of reach
once pKVM has deprivileged the kernel. The CPU never boots.
Since pKVM doesn't allow late onlining of CPUs, we can detect
that protected mode is enforced early on, and return the current
state of the capability.
Fixes: 2a28810cbb8b2 ("KVM: arm64: GICv3: Detect and work around the lack of ICV_DIR_EL1 trapping")
Reported-by: Vincent Donnefort <vdonnefort@google.com>
Tested-by: Vincent Donnefort <vdonnefort@google.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20260310085433.3936742-1-maz@kernel.org
Cc: stable@vger.kernel.org
|
|
'net-enetc-fix-fallback-phy-address-handling-and-do-not-skip-setting-for-addr-0'
Wei Fang says:
====================
net: enetc: fix fallback PHY address handling and do not skip setting for addr 0
There are two potential issues when PHY address 0 is used on the board,
see the commit messages of the patches for more details.
v1: https://lore.kernel.org/imx/20260303103047.228005-1-wei.fang@nxp.com/
====================
Link: https://patch.msgid.link/20260305031211.904812-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Given that some platforms may use PHY address 0 (I suppose the PHY may
not treat address 0 as a broadcast address or default response address).
It is possible for some boards to connect multiple PHYs to the same
ENETC MAC, for example:
- a PHY with a non-zero address connects to ENETC MAC through SGMII
interface (selected via DTS_A)
- a PHY with address 0 connects to ENETC MAC through RGMII interface
(selected via DTS_B)
For the case where the ENETC port MDIO is used to manage the PHY, when
switching from DTS_A to DTS_B via soft reboot, LaBCR[MDIO_PHYAD_PRTAD]
must be updated to 0 because the NETCMIX block is not reset during soft
reboot. However, the current driver explicitly skips configuring address
0, causing LaBCR[MDIO_PHYAD_PRTAD] to retain its old value.
Therefore, remove the special-case skip of PHY address 0 so that valid
configurations using address 0 are properly supported.
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current netc_get_phy_addr() implementation falls back to PHY address
0 when the "mdio" node or the PHY child node is missing. On i.MX95, this
causes failures when a real PHY is actually assigned address 0 and is
managed through the EMDIO interface. Because the bit 0 of phy_mask will
be set, leading imx95_enetc_mdio_phyaddr_config() to return an error, and
the netc_blk_ctrl driver probe subsequently fails. Fix this by returning
-ENODEV when neither an "mdio" node nor any PHY node is present, it means
that ENETC port MDIO is not used to manage the PHY, so there is no need
to configure LaBCR[MDIO_PHYAD_PRTAD].
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/all/7825188.GXAFRqVoOG@steina-w
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The GPIO .get() callback is expected to return 0 or 1 (or a negative
error code). Ensure that the value returned by rza1_gpio_get() is
normalized to the [0, 1] range.
Fixes: 86ef402d805d606a ("gpiolib: sanitize the return value of gpio_chip::get()")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/aZYnyl-Nf4S1U2yj@google.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
GPIO controller driver should typically implement the .get_direction()
callback as GPIOLIB internals may try to use it to determine the state
of a pin. Since introduction of shared proxy, it prints a warning splat
when using a shared spmi gpio.
The implementation is not easy because the controller supports enabling
the input and output logic at the same time, so we aligns on the
behaviour of the .get() operation and return -EINVAL in other
situations.
Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Fixes: d7b5f5cc5eb4 ("pinctrl: qcom: spmi-gpio: Add support for GPIO LV/MV subtype")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
In xfs_qm_dqflush(), when a dquot flush fails due to corruption
(the out_abort error path), the original code removed the dquot log
item from the AIL before calling xfs_force_shutdown(). This ordering
introduces a subtle race condition that can lead to data loss after
a crash.
The AIL tracks the oldest dirty metadata in the journal. The position
of the tail item in the AIL determines the log tail LSN, which is the
oldest LSN that must be preserved for crash recovery. When an item is
removed from the AIL, the log tail can advance past the LSN of that item.
The race window is as follows: if the dquot item happens to be at
the tail of the log, removing it from the AIL allows the log tail
to advance. If a concurrent log write is sampling the tail LSN at
the same time and subsequently writes a complete checkpoint (i.e.,
one containing a commit record) to disk before the shutdown takes
effect, the journal will no longer protect the dquot's last
modification. On the next mount, log recovery will not replay the
dquot changes, even though they were never written back to disk,
resulting in silent data loss.
Fix this by calling xfs_force_shutdown() before xfs_trans_ail_delete()
in the out_abort path. Once the log is shut down, no new log writes
can complete with an updated tail LSN, making it safe to remove the
dquot item from the AIL.
Cc: stable@vger.kernel.org
Fixes: b707fffda6a3 ("xfs: abort consistently on dquot flush failure")
Signed-off-by: Long Li <leo.lilong@huawei.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
ip->i_itemp has been set null in xfs_inode_item_destroy(), so there is
no need set it null again in xfs_inode_free_callback().
Signed-off-by: Long Li <leo.lilong@huawei.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
The Scarlett2 mixer quirk in USB-audio driver may hit a NULL
dereference when a malformed USB descriptor is passed, since it
assumes the presence of an endpoint in the parsed interface in
scarlett2_find_fc_interface(), as reported by fuzzer.
For avoiding the NULL dereference, just add the sanity check of
bNumEndpoints and skip the invalid interface.
Reported-by: syzbot+8f29539ef9a1c8334f42@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/69acbbe1.050a0220.310d8.0001.GAE@google.com
Reported-by: syzbot+ae893a8901067fde2741@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/69acf72a.050a0220.310d8.0004.GAE@google.com
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260309104632.141895-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For eDP read the ALPM DPCD caps after DPCD initalization and just before
the PSR init.
v2: Move intel_alpm_init to intel_edp_init_dpcd (Jouni)
v3: Add Fixes with commit-id (Jouni)
v4: Separated the alpm dpcd read caps from alpm_init and moved to
intel_edp_init_dpcd.
v5: Read alpm_caps always for eDP irrespective of the eDP version (Jouni)
v6: replace drm_dp_dpcd_readb with drm_dp_dpcd_read_byte (Jouni)
Fixes: 15438b325987 ("drm/i915/alpm: Add compute config for lobf")
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patch.msgid.link/20260304072157.1123283-1-arun.r.murthy@intel.com
(cherry picked from commit 88442ba208dd5d3405de3f5000cf5b2c86876ae3)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
There are slice row per frame and pic height parameters in DSC that needs
to be configured on every Selective Update in Early Transport mode. Use
helper provided by DSC code to configure these on Selective Update when in
Early Transport mode. Also fill crtc_state->psr2_su_area with full frame
area on full frame update for DSC calculation.
v2: move psr2_su_area under skip_sel_fetch_set_loop label
Bspec: 68927, 71709
Fixes: 467e4e061c44 ("drm/i915/psr: Enable psr2 early transport as possible")
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260304113011.626542-5-jouni.hogander@intel.com
(cherry picked from commit 3140af2fab505a4cd47d516284529bf1585628be)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
There are slice row per frame and pic height configuration in DSC Selective
Update Parameter Set 1 register. Add helper for configuring these.
v2:
- Add WARN_ON_ONCE if vdsc instances per pipe > 2
- instead of checking vdsc instances per pipe being > 1 check == 2
Bspec: 71709
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260304113011.626542-4-jouni.hogander@intel.com
(cherry picked from commit c8698d61aeb3f70fe33761ee9d3d0e131b5bc2eb)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
[tursulin: fixup forward declaration conflict]
|
|
Add definitions for DSC_SU_PARAMETER_SET_0_DSC0 and
DSC_SU_PARAMETER_SET_0_DSC1 registers. These are for Selective Update Early
Transport configuration.
Bspec: 71709
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260304113011.626542-3-jouni.hogander@intel.com
(cherry picked from commit 24f96d903daf3dcf8fafe84d3d22b80ef47ba493)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
Currently we are aligning Selective Update area to cover cursor fully if
needed only once. It may happen that cursor is in Selective Update area
after pipe alignment and after that covering cursor plane only
partially. Fix this by looping alignment as long as alignment isn't needed
anymore.
v2:
- do not unecessarily loop if cursor was already fully covered
- rename aligned as su_area_changed
Fixes: 1bff93b8bc27 ("drm/i915/psr: Extend SU area to cover cursor fully if needed")
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260304113011.626542-2-jouni.hogander@intel.com
(cherry picked from commit 681e12440d8b110350a5709101169f319e10ccbb)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
When a scatterlists table of a GEM shmem object of size 4 GB or more is
populated with pages allocated from a folio, unsigned int .length
attribute of a scatterlist may get overflowed if total byte length of
pages allocated to that single scatterlist happens to reach or cross the
4GB limit. As a consequence, users of the object may suffer from hitting
unexpected, premature end of the object's backing pages.
[278.780187] ------------[ cut here ]------------
[278.780377] WARNING: CPU: 1 PID: 2326 at drivers/gpu/drm/i915/i915_mm.c:55 remap_sg+0x199/0x1d0 [i915]
...
[278.780654] CPU: 1 UID: 0 PID: 2326 Comm: gem_mmap_offset Tainted: G S U 6.17.0-rc1-CI_DRM_16981-ged823aaa0607+ #1 PREEMPT(voluntary)
[278.780656] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
[278.780658] Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P LP5x T3 RVP, BIOS MTLPFWI1.R00.3471.D91.2401310918 01/31/2024
[278.780659] RIP: 0010:remap_sg+0x199/0x1d0 [i915]
...
[278.780786] Call Trace:
[278.780787] <TASK>
[278.780788] ? __apply_to_page_range+0x3e6/0x910
[278.780795] ? __pfx_remap_sg+0x10/0x10 [i915]
[278.780906] apply_to_page_range+0x14/0x30
[278.780908] remap_io_sg+0x14d/0x260 [i915]
[278.781013] vm_fault_cpu+0xd2/0x330 [i915]
[278.781137] __do_fault+0x3a/0x1b0
[278.781140] do_fault+0x322/0x640
[278.781143] __handle_mm_fault+0x938/0xfd0
[278.781150] handle_mm_fault+0x12c/0x300
[278.781152] ? lock_mm_and_find_vma+0x4b/0x760
[278.781155] do_user_addr_fault+0x2d6/0x8e0
[278.781160] exc_page_fault+0x96/0x2c0
[278.781165] asm_exc_page_fault+0x27/0x30
...
That issue was apprehended by the author of a change that introduced it,
and potential risk even annotated with a comment, but then never addressed.
When adding folio pages to a scatterlist table, take care of byte length
of any single scatterlist not exceeding max_segment.
Fixes: 0b62af28f249b ("i915: convert shmem_sg_free_table() to use a folio_batch")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14809
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20260224094944.2447913-2-janusz.krzysztofik@linux.intel.com
(cherry picked from commit 06249b4e691a75694c014a61708c007fb5755f60)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
Apparently ICL may hang with an MCE if we write TRANS_VRR_VMAX/FLIPLINE
before enabling TRANS_DDI_FUNC_CTL.
Personally I was only able to reproduce a hang (on an Dell XPS 7390
2-in-1) with an external display connected via a dock using a dodgy
type-C cable that made the link training fail. After the failed
link training the machine would hang. TGL seemed immune to the
problem for whatever reason.
BSpec does tell us to configure VRR after enabling TRANS_DDI_FUNC_CTL
as well. The DMC firmware also does the VRR restore in two stages:
- first stage seems to be unconditional and includes TRANS_VRR_CTL
and a few other VRR registers, among other things
- second stage is conditional on the DDI being enabled,
and includes TRANS_DDI_FUNC_CTL and TRANS_VRR_VMAX/VMIN/FLIPLINE,
among other things
So let's reorder the steps to match to avoid the hang, and
toss in an extra WARN to make sure we don't screw this up later.
BSpec: 22243
Cc: stable@vger.kernel.org
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reported-by: Benjamin Tissoires <bentiss@kernel.org>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/15777
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Fixes: dda7dcd9da73 ("drm/i915/vrr: Use fixed timings for platforms that support VRR")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260303095414.4331-1-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
(cherry picked from commit 93f3a267c3dd4d811b224bb9e179a10d81456a74)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
When changing channels, the current check in bnxt_set_channels()
is not checking for non-default RSS contexts when the RSS table size
changes. The current check for IFF_RXFH_CONFIGURED is only sufficient
for the default RSS context. Expand the check to include the presence
of any non-default RSS contexts.
Allowing such change will result in incorrect configuration of the
context's RSS table when the table size changes.
Fixes: b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
Reported-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/netdev/20260303181535.2671734-1-bjorn@kernel.org/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260306225854.3575672-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Oleksij Rempel says:
====================
net: usb: lan78xx: accumulated bug fixes
This series contains a collection of standalone bug fixes for the
Microchip LAN78xx driver, addressing packet handling, TX statistics,
invalid register accesses, and a kernel warning during disconnect.
====================
Link: https://patch.msgid.link/20260305143429.530909-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
