| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 523184972b282cd9ca17a76f6ca4742394856818 ]
With virtual PCI-Express chipsets, we now see userspace/guest drivers
trying to match the physical MPS setting to a virtual downstream port.
Of course a lone physical device surrounded by virtual interconnects
cannot make a correct decision for a proper MPS setting. Instead,
let's virtualize the MPS control register so that writes through to
hardware are disallowed. Userspace drivers like QEMU assume they can
write anything to the device and we'll filter out anything dangerous.
Since mismatched MPS can lead to AER and other faults, let's add it
to the kernel side rather than relying on userspace virtualization to
handle it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit ddf9dc0eb5314d6dac8b19b1cc37c739c6896e7e ]
We use a BAR restore trick to try to detect when a user has performed
a device reset, possibly through FLR or other backdoors, to put things
back into a working state. This is important for backdoor resets, but
we can actually just virtualize the "front door" resets provided via
PCIe and AF FLR. Set these bits as virtualized + writable, allowing
the default write to set them in vconfig, then we can simply check the
bit, perform an FLR of our own, and clear the bit. We don't actually
have the granularity in PCI to specify the type of reset we want to
do, but generally devices don't implement both PCIe and AF FLR and
we'll favor these over other types of reset, so we should generally
lineup. We do test whether the device provides the requested FLR type
to stay consistent with hardware capabilities though.
This seems to fix several instance of devices getting into bad states
with userspace drivers, like dpdk, running inside a VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Rose <grose@lightfleet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e15dc99dbb9cf99f6432e8e3c0b3a8f7a3403a86 ]
The commit 02a5d6925cd3 ("ALSA: pcm: Avoid potential races between OSS
ioctls and read/write") split the PCM preparation code to a locked
version, and it added a sanity check of runtime->oss.prepare flag
along with the change. This leaded to an endless loop when the stream
gets XRUN: namely, snd_pcm_oss_write3() and co call
snd_pcm_oss_prepare() without setting runtime->oss.prepare flag and
the loop continues until the PCM state reaches to another one.
As the function is supposed to execute the preparation
unconditionally, drop the invalid state check there.
The bug was triggered by syzkaller.
Fixes: 02a5d6925cd3 ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write")
Reported-by: syzbot+150189c103427d31a053@syzkaller.appspotmail.com
Reported-by: syzbot+7e3f31a52646f939c052@syzkaller.appspotmail.com
Reported-by: syzbot+4f2016cf5185da7759dc@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit f6d297df4dd47ef949540e4a201230d0c5308325 ]
The previous fix 40cab6e88cb0 ("ALSA: pcm: Return -EBUSY for OSS
ioctls changing busy streams") introduced some mutex unbalance; the
check of runtime->oss.rw_ref was inserted in a wrong place after the
mutex lock.
This patch fixes the inconsistency by rewriting with the helper
functions to lock/unlock parameters with the stream check.
Fixes: 40cab6e88cb0 ("ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 40cab6e88cb0b6c56d3f30b7491a20e803f948f6 ]
OSS PCM stream management isn't modal but it allows ioctls issued at
any time for changing the parameters. In the previous hardening
patch ("ALSA: pcm: Avoid potential races between OSS ioctls and
read/write"), we covered these races and prevent the corruption by
protecting the concurrent accesses via params_lock mutex. However,
this means that some ioctls that try to change the stream parameter
(e.g. channels or format) would be blocked until the read/write
finishes, and it may take really long.
Basically changing the parameter while reading/writing is an invalid
operation, hence it's even more user-friendly from the API POV if it
returns -EBUSY in such a situation.
This patch adds such checks in the relevant ioctls with the addition
of read/write access refcount.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 02a5d6925cd34c3b774bdb8eefb057c40a30e870 ]
Although we apply the params_lock mutex to the whole read and write
operations as well as snd_pcm_oss_change_params(), we may still face
some races.
First off, the params_lock is taken inside the read and write loop.
This is intentional for avoiding the too long locking, but it allows
the in-between parameter change, which might lead to invalid
pointers. We check the readiness of the stream and set up via
snd_pcm_oss_make_ready() at the beginning of read and write, but it's
called only once, by assuming that it remains ready in the rest.
Second, many ioctls that may change the actual parameters
(i.e. setting runtime->oss.params=1) aren't protected, hence they can
be processed in a half-baked state.
This patch is an attempt to plug these holes. The stream readiness
check is moved inside the read/write inner loop, so that the stream is
always set up in a proper state before further processing. Also, each
ioctl that may change the parameter is wrapped with the params_lock
for avoiding the races.
The issues were triggered by syzkaller in a few different scenarios,
particularly the one below appearing as GPF in loopback_pos_update.
Reported-by: syzbot+c4227aec125487ec3efa@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c64ed5dd9feba193c76eb460b451225ac2a0d87b ]
Fix the last standing EINTR in the whole subsystem. Use more correct
ERESTARTSYS for pending signals.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 46325371b230cc66c743925c930a17e7d0b8211e ]
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kzalloc.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 977f6f68331f94bb72ad84ee96b7b87ce737d89d ]
F71808FG_FLAG_WD_EN defines bit position, not a bitmask
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6a4a4595804548e173f0763a0e7274a3521c59a9 ]
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).
They have also some dip-switches to select a different clock (666, 800,
1066, 1200).
The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).
This patch add all the missing clocks.
The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).
Fixes: 0e85aeced4d6 ("clk: mvebu: add clock support for Armada 380/385")
Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56cf5: clk: mvebu: armada-38x: add support for 1866MHz variants
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 9593f4f56cf5d1c443f66660a0c7f01de38f979d ]
The Linksys WRT3200ACM CPU is clocked at 1866MHz. Add 1866MHz to the
list of supported CPU frequencies. Also update multiplier and divisor
for the l2clk and ddrclk.
Noticed by the following warning:
[ 0.000000] Selected CPU frequency (16) unsupported
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit a04f0017c22453613d5f423326b190c61e3b4f98 ]
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb85687 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 4d1a535b8ec5e74b42dfd9dc809142653b2597f6 ]
glibc 2.26 removed the 'struct ucontext' to "improve" POSIX compliance
and break programs, including User Mode Linux. Fix User Mode Linux
by using POSIX ucontext_t.
This fixes:
arch/um/os-Linux/signal.c: In function 'hard_handler':
arch/um/os-Linux/signal.c:163:22: error: dereferencing pointer to incomplete type 'struct ucontext'
mcontext_t *mc = &uc->uc_mcontext;
arch/x86/um/stub_segv.c: In function 'stub_segv_handler':
arch/x86/um/stub_segv.c:16:13: error: dereferencing pointer to incomplete type 'struct ucontext'
&uc->uc_mcontext);
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c5637476bbf9bb86c7f0413b8f4822a73d8d2d07 ]
Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.
Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":
INITD -------- ------------
|____________________|
_______________________ _______________
NDA @desc2 \/ @desc3
_______________________/\_______________
__________ ___________ _______________
CUBC 0 \/ MAX desc1 \/ MAX desc2
__________/\___________/\_______________
| | | |
Events:(1)(2) (3)(4)
(1) check_nda = @desc2
(2) initd = 1
(3) cur_ubc = MAX desc1
(4) cur_nda = @desc2
This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.
This error leads to incorrect residue computation.
Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.
Fixes: 53398f488821 ("dmaengine: at_xdmac: fix residue corruption")
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 3a148896b24adf8688dc0c59af54531931677a40 ]
Ensure that cv_end is equal to ibdev->num_comp_vectors for the
NUMA node with the highest index. This patch improves spreading
of RDMA channels over completion vectors and thereby improves
performance, especially on systems with only a single NUMA node.
This patch drops support for the comp_vector login parameter by
ignoring the value of that parameter since I have not found a
good way to combine support for that parameter and automatic
spreading of RDMA channels over completion vectors.
Fixes: d92c0da71a35 ("IB/srp: Add multichannel support")
Reported-by: Alexander Schmid <alex@modula-shop-systems.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Alexander Schmid <alex@modula-shop-systems.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e68088e78d82920632eba112b968e49d588d02a2 ]
Before commit e494f6a72839 ("[SCSI] improved eh timeout handler") it
did not really matter whether or not abort handlers like srp_abort()
called .scsi_done() when returning another value than SUCCESS. Since
that commit however this matters. Hence only call .scsi_done() when
returning SUCCESS.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 8435168d50e66fa5eae01852769d20a36f9e5e83 ]
Check to make sure that ctx->cm_id->device is set before we use it.
Otherwise userspace can trigger a NULL dereference by doing
RDMA_USER_CM_CMD_SET_OPTION on an ID that is not bound to a device.
Cc: <stable@vger.kernel.org>
Reported-by: <syzbot+a67bc93e14682d92fc2f@syzkaller.appspotmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 85e0c4e89c1b864e763c4e3bb15d0b6d501ad5d9 ]
This updates the jbd2 superblock unnecessarily, and on an abort we
shouldn't truncate the log.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 9f886f4d1d292442b2f22a0a33321eae821bde40 ]
This fixes a harmless UBSAN where root could potentially end up
causing an overflow while bumping the entropy_total field (which is
ignored once the entropy pool has been initialized, and this generally
is completed during the boot sequence).
This is marginal for the stable kernel series, but it's a really
trivial patch, and it fixes UBSAN warning that might cause security
folks to get overly excited for no reason.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Chen Feng <puck.chen@hisilicon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit f2a659f7d8d5da803836583aa16df06bdf324252 ]
The driver misses implementation of PM hook that undoes what
->freeze_noirq() does after the hibernation image is created. This means
the control channel is not resumed properly and the Thunderbolt bus
becomes useless in later stages of hibernation (when the image is stored
or if the operation fails).
Fix this by pointing ->thaw_noirq to driver nhi_resume_noirq(). This
makes sure the control channel is resumed properly.
Fixes: 23dd5bb49d98 ("thunderbolt: Add suspend/hibernate support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit a01df75ce737951ad13a08d101306e88c3f57cb2 ]
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6de0b13cc0b4ba10e98a9263d7a83b940720b77a ]
When size is negative, calling memset will make segment fault.
Declare the size as type u32 to keep memset safe.
size in struct hid_report is unsigned, fix return type of
hid_report_len to u32.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 3b8070335f751aac9f1526ae2e012e6f5b8b0f21 ]
The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de9fe3 ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 34dd25de9fe3f60bfdb31b473bf04b28262d0896 ]
This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.
The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.
This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 0bfdf598900fd62869659f360d3387ed80eb71cf ]
asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.
__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.
Fixes: 46d075be585e ("powerpc: Optimise smp_wmb")
Cc: stable@vger.kernel.org # v2.6.29+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 741de617661794246f84a21a02fc5e327bffc9ad ]
opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit ac75a041048b8c1f7418e27621ca5efda8571043 ]
When convert char array with signed int, if the inbuf[x] is negative then
upper bits will be set to 1. Fix this by using u8 instead of char.
ret_size has to be at least 3, hid_input_report use it after minus 2 bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit cabdf83dadfb3d83eec31e0f0638a92dbd716435 ]
Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.
Cc: <stable@vger.kernel.org>
Fixes: f1c7e7108109 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 64627388b50158fd24d6ad88132525b95a5ef573 ]
USB3 hubs don't support global suspend.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 13d3047c81505cc0fb9bdae7810676e70523c8bf ]
Mike Lothian reported that plugging in a USB-C device does not work
properly in his Dell Alienware system. This system has an Intel Alpine
Ridge Thunderbolt controller providing USB-C functionality. In these
systems the USB controller (xHCI) is hotplugged whenever a device is
connected to the port using ACPI-based hotplug.
The ACPI description of the root port in question is as follows:
Device (RP01)
{
Name (_ADR, 0x001C0000)
Device (PXSX)
{
Name (_ADR, 0x02)
Method (_RMV, 0, NotSerialized)
{
// ...
}
}
Here _ADR 0x02 means device 0, function 2 on the bus under root port (RP01)
but that seems to be incorrect because device 0 is the upstream port of the
Alpine Ridge PCIe switch and it has no functions other than 0 (the bridge
itself). When we get ACPI Notify() to the root port resulting from
connecting a USB-C device, Linux tries to read PCI_VENDOR_ID from device 0,
function 2 which of course always returns 0xffffffff because there is no
such function and we never find the device.
In Windows this works fine.
Now, since we get ACPI Notify() to the root port and not to the PXSX device
we should actually start our scan from there as well and not from the
non-existent PXSX device. Fix this by checking presence of the slot itself
(function 0) if we fail to do that otherwise.
While there use pci_bus_read_dev_vendor_id() in get_slot_status(), which is
the recommended way to read Device and Vendor IDs of devices on PCI buses.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198557
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c2d2e6738a209f0f9dffa2dc8e7292fc45360d61 ]
A toolstack may delete the vif frontend and backend xenstore entries
while xen-netfront is in the removal code path. In that case, the
checks for xenbus_read_driver_state would return XenbusStateUnknown, and
xennet_remove would hang indefinitely. This hang prevents system
shutdown.
xennet_remove must be able to handle XenbusStateUnknown, and
netback_changed must also wake up the wake_queue for that state as well.
Fixes: 5b5971df3bc2 ("xen-netfront: remove warning when unloading module")
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Cc: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e8fd0adf105e132fd84545997bbef3d5edc2c9c1 ]
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit af6f8529098aeb0e56a68671b450cf74e7a64fcd ]
musb->endpoints[] has array size MUSB_C_NUM_EPS.
We must check array bounds before accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 3f05317d9889ab75c7190dcd39491d2a97921984 ]
syzbot reported a use-after-free of shm_file_data(file)->file->f_op in
shm_get_unmapped_area(), called via sys_remap_file_pages().
Unfortunately it couldn't generate a reproducer, but I found a bug which
I think caused it. When remap_file_pages() is passed a full System V
shared memory segment, the memory is first unmapped, then a new map is
created using the ->vm_file. Between these steps, the shm ID can be
removed and reused for a new shm segment. But, shm_mmap() only checks
whether the ID is currently valid before calling the underlying file's
->mmap(); it doesn't check whether it was reused. Thus it can use the
wrong underlying file, one that was already freed.
Fix this by making the "outer" shm file (the one that gets put in
->vm_file) hold a reference to the real shm file, and by making
__shm_open() require that the file associated with the shm ID matches
the one associated with the "outer" file.
Taking the reference to the real shm file is needed to fully solve the
problem, since otherwise sfd->file could point to a freed file, which
then could be reallocated for the reused shm ID, causing the wrong shm
segment to be mapped (and without the required permission checks).
Commit 1ac0b6dec656 ("ipc/shm: handle removed segments gracefully in
shm_mmap()") almost fixed this bug, but it didn't go far enough because
it didn't consider the case where the shm ID is reused.
The following program usually reproduces this bug:
#include <stdlib.h>
#include <sys/shm.h>
#include <sys/syscall.h>
#include <unistd.h>
int main()
{
int is_parent = (fork() != 0);
srand(getpid());
for (;;) {
int id = shmget(0xF00F, 4096, IPC_CREAT|0700);
if (is_parent) {
void *addr = shmat(id, NULL, 0);
usleep(rand() % 50);
while (!syscall(__NR_remap_file_pages, addr, 4096, 0, 0, 0));
} else {
usleep(rand() % 50);
shmctl(id, IPC_RMID, NULL);
}
}
}
It causes the following NULL pointer dereference due to a 'struct file'
being used while it's being freed. (I couldn't actually get a KASAN
use-after-free splat like in the syzbot report. But I think it's
possible with this bug; it would just take a more extraordinary race...)
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 9 PID: 258 Comm: syz_ipc Not tainted 4.16.0-05140-gf8cf2f16a7c95 #189
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
RIP: 0010:d_inode include/linux/dcache.h:519 [inline]
RIP: 0010:touch_atime+0x25/0xd0 fs/inode.c:1724
[...]
Call Trace:
file_accessed include/linux/fs.h:2063 [inline]
shmem_mmap+0x25/0x40 mm/shmem.c:2149
call_mmap include/linux/fs.h:1789 [inline]
shm_mmap+0x34/0x80 ipc/shm.c:465
call_mmap include/linux/fs.h:1789 [inline]
mmap_region+0x309/0x5b0 mm/mmap.c:1712
do_mmap+0x294/0x4a0 mm/mmap.c:1483
do_mmap_pgoff include/linux/mm.h:2235 [inline]
SYSC_remap_file_pages mm/mmap.c:2853 [inline]
SyS_remap_file_pages+0x232/0x310 mm/mmap.c:2769
do_syscall_64+0x64/0x1a0 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
[ebiggers@google.com: add comment]
Link: http://lkml.kernel.org/r/20180410192850.235835-1-ebiggers3@gmail.com
Link: http://lkml.kernel.org/r/20180409043039.28915-1-ebiggers3@gmail.com
Reported-by: syzbot+d11f321e7f1923157eac80aa990b446596f46439@syzkaller.appspotmail.com
Fixes: c8d78c1823f4 ("mm: replace remap_file_pages() syscall with emulation")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 60bb83b81169820c691fbfa33a6a4aef32aa4b0b ]
We've got a bug report indicating a kernel panic at booting on an x86-32
system, and it turned out to be the invalid PCI resource assigned after
reallocation. __find_resource() first aligns the resource start address
and resets the end address with start+size-1 accordingly, then checks
whether it's contained. Here the end address may overflow the integer,
although resource_contains() still returns true because the function
validates only start and end address. So this ends up with returning an
invalid resource (start > end).
There was already an attempt to cover such a problem in the commit
47ea91b4052d ("Resource: fix wrong resource window calculation"), but
this case is an overseen one.
This patch adds the validity check of the newly calculated resource for
avoiding the integer overflow problem.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739
Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de
Fixes: 23c570a67448 ("resource: ability to resize an allocated resource")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Michael Henders <hendersm@shaw.ca>
Tested-by: Michael Henders <hendersm@shaw.ca>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 9ad553abe66f8be3f4755e9fa0a6ba137ce76341 ]
One use of the reiserfs_warning() macro in journal_init_dev() is missing
a parameter, causing the following warning:
REISERFS warning (device loop0): journal_init_dev: Cannot open '%s': %i journal_init_dev:
This also causes a WARN_ONCE() warning in the vsprintf code, and then a
panic if panic_on_warn is set.
Please remove unsupported %/ in format string
WARNING: CPU: 1 PID: 4480 at lib/vsprintf.c:2138 format_decode+0x77f/0x830 lib/vsprintf.c:2138
Kernel panic - not syncing: panic_on_warn set ...
Just add another string argument to the macro invocation.
Addresses https://syzkaller.appspot.com/bug?id=0627d4551fdc39bf1ef5d82cd9eef587047f7718
Link: http://lkml.kernel.org/r/d678ebe1-6f54-8090-df4c-b9affad62293@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: <syzbot+6bd77b88c1977c03f584@syzkaller.appspotmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jan Kara <jack@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit b5094b7f135be34630e3ea8a98fa215715d0f29d ]
While UBI and UBIFS seem to work at first sight with MLC NAND, you will
most likely lose all your data upon a power-cut or due to read/write
disturb.
In order to protect users from bad surprises, refuse to attach to MLC
NAND.
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 78a8dfbabbece22bee58ac4cb26cab10e7a19c5d ]
When opening a device with write access, ubiblock_open returns an error
code. Currently, this error code is -EPERM, but this is not the right
value.
The open function for other block devices returns -EROFS when opening
read-only devices with FMODE_WRITE set. When used with dm-verity, the
veritysetup userspace tool is expecting EROFS, and refuses to use the
ubiblock device.
Use -EROFS for ubiblock as well. As a result, veritysetup accepts the
ubiblock device as valid.
Cc: stable@vger.kernel.org
Fixes: 9d54c8a33eec (UBI: R/O block driver on top of UBI volumes)
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 29b7a6fa1ec07e8480b0d9caf635a4498a438bf4 ]
At this point UBI volumes have already been free()'ed and fastmap can no
longer access these data structures.
Reported-by: Martin Townsend <mtownsend1973@gmail.com>
Fixes: 74cdaf24004a ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system")
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit aac17948a7ce01fb60b9ee6cf902967a47b3ce26 ]
If ubifs_wbuf_sync() fails we must not write a master node with the
dirty marker cleared.
Otherwise it is possible that in case of an IO error while syncing we
mark the filesystem as clean and UBIFS refuses to recover upon next
mount.
Cc: <stable@vger.kernel.org>
Fixes: 1e51764a3c2a ("UBIFS: add new flash file system")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 28b0f8a6962a24ed21737578f3b1b07424635c9e ]
A tty is hung up by __tty_hangup() setting file->f_op to
hung_up_tty_fops, which is skipped on ttys whose write operation isn't
tty_write(). This means that, for example, /dev/console whose write
op is redirected_tty_write() is never actually marked hung up.
Because n_tty_read() uses the hung up status to decide whether to
abort the waiting readers, the lack of hung-up marking can lead to the
following scenario.
1. A session contains two processes. The leader and its child. The
child ignores SIGHUP.
2. The leader exits and starts disassociating from the controlling
terminal (/dev/console).
3. __tty_hangup() skips setting f_op to hung_up_tty_fops.
4. SIGHUP is delivered and ignored.
5. tty_ldisc_hangup() is invoked. It wakes up the waits which should
clear the read lockers of tty->ldisc_sem.
6. The reader wakes up but because tty_hung_up_p() is false, it
doesn't abort and goes back to sleep while read-holding
tty->ldisc_sem.
7. The leader progresses to tty_ldisc_lock() in tty_ldisc_hangup()
and is now stuck in D sleep indefinitely waiting for
tty->ldisc_sem.
The following is Alan's explanation on why some ttys aren't hung up.
http://lkml.kernel.org/r/20171101170908.6ad08580@alans-desktop
1. It broke the serial consoles because they would hang up and close
down the hardware. With tty_port that *should* be fixable properly
for any cases remaining.
2. The console layer was (and still is) completely broken and doens't
refcount properly. So if you turn on console hangups it breaks (as
indeed does freeing consoles and half a dozen other things).
As neither can be fixed quickly, this patch works around the problem
by introducing a new flag, TTY_HUPPING, which is used solely to tell
n_tty_read() that hang-up is in progress for the console and the
readers should be aborted regardless of the hung-up status of the
device.
The following is a sample hung task warning caused by this issue.
INFO: task agetty:2662 blocked for more than 120 seconds.
Not tainted 4.11.3-dbg-tty-lockup-02478-gfd6c7ee-dirty #28
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
0 2662 1 0x00000086
Call Trace:
__schedule+0x267/0x890
schedule+0x36/0x80
schedule_timeout+0x23c/0x2e0
ldsem_down_write+0xce/0x1f6
tty_ldisc_lock+0x16/0x30
tty_ldisc_hangup+0xb3/0x1b0
__tty_hangup+0x300/0x410
disassociate_ctty+0x6c/0x290
do_exit+0x7ef/0xb00
do_group_exit+0x3f/0xa0
get_signal+0x1b3/0x5d0
do_signal+0x28/0x660
exit_to_usermode_loop+0x46/0x86
do_syscall_64+0x9c/0xb0
entry_SYSCALL64_slow_path+0x25/0x25
The following is the repro. Run "$PROG /dev/console". The parent
process hangs in D state.
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/wait.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <errno.h>
#include <signal.h>
#include <time.h>
#include <termios.h>
int main(int argc, char **argv)
{
struct sigaction sact = { .sa_handler = SIG_IGN };
struct timespec ts1s = { .tv_sec = 1 };
pid_t pid;
int fd;
if (argc < 2) {
fprintf(stderr, "test-hung-tty /dev/$TTY\n");
return 1;
}
/* fork a child to ensure that it isn't already the session leader */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
/* top parent, wait for everyone */
while (waitpid(-1, NULL, 0) >= 0)
;
if (errno != ECHILD)
perror("waitpid");
return 0;
}
/* new session, start a new session and set the controlling tty */
if (setsid() < 0) {
perror("setsid");
return 1;
}
fd = open(argv[1], O_RDWR);
if (fd < 0) {
perror("open");
return 1;
}
if (ioctl(fd, TIOCSCTTY, 1) < 0) {
perror("ioctl");
return 1;
}
/* fork a child, sleep a bit and exit */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
nanosleep(&ts1s, NULL);
printf("Session leader exiting\n");
exit(0);
}
/*
* The child ignores SIGHUP and keeps reading from the controlling
* tty. Because SIGHUP is ignored, the child doesn't get killed on
* parent exit and the bug in n_tty makes the read(2) block the
* parent's control terminal hangup attempt. The parent ends up in
* D sleep until the child is explicitly killed.
*/
sigaction(SIGHUP, &sact, NULL);
printf("Child reading tty\n");
while (1) {
char buf[1024];
if (read(fd, buf, sizeof(buf)) < 0) {
perror("read");
return 1;
}
}
return 0;
}
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 3f01ddb962dc506916c243f9524e8bef97119b77 ]
On receiving a packet the state index points to the rstate which must be
used to fill up IP and TCP headers. But if the state index points to a
rstate which is unitialized, i.e. filled with zeros, it gets stuck in an
infinite loop inside ip_fast_csum trying to compute the ip checsum of a
header with zero length.
89.666953: <2> [<ffffff9dd3e94d38>] slhc_uncompress+0x464/0x468
89.666965: <2> [<ffffff9dd3e87d88>] ppp_receive_nonmp_frame+0x3b4/0x65c
89.666978: <2> [<ffffff9dd3e89dd4>] ppp_receive_frame+0x64/0x7e0
89.666991: <2> [<ffffff9dd3e8a708>] ppp_input+0x104/0x198
89.667005: <2> [<ffffff9dd3e93868>] pppopns_recv_core+0x238/0x370
89.667027: <2> [<ffffff9dd4428fc8>] __sk_receive_skb+0xdc/0x250
89.667040: <2> [<ffffff9dd3e939e4>] pppopns_recv+0x44/0x60
89.667053: <2> [<ffffff9dd4426848>] __sock_queue_rcv_skb+0x16c/0x24c
89.667065: <2> [<ffffff9dd4426954>] sock_queue_rcv_skb+0x2c/0x38
89.667085: <2> [<ffffff9dd44f7358>] raw_rcv+0x124/0x154
89.667098: <2> [<ffffff9dd44f7568>] raw_local_deliver+0x1e0/0x22c
89.667117: <2> [<ffffff9dd44c8ba0>] ip_local_deliver_finish+0x70/0x24c
89.667131: <2> [<ffffff9dd44c92f4>] ip_local_deliver+0x100/0x10c
./scripts/faddr2line vmlinux slhc_uncompress+0x464/0x468 output:
ip_fast_csum at arch/arm64/include/asm/checksum.h:40
(inlined by) slhc_uncompress at drivers/net/slip/slhc.c:615
Adding a variable to indicate if the current rstate is initialized. If
such a packet arrives, move to toss state.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 53765341ee821c0a0f1dec41adc89c9096ad694c ]
The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.
The modem is controlled via AT commands through the exposed TTYs.
AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 7972326a26b5bf8dc2adac575c4e03ee7e9d193a ]
This can be reproduced by bind/unbind the driver multiple times
in AM3517 board.
Analysis revealed that rtl8187_start() was invoked before probe
finishes(ie. before the mutex is initialized).
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
[<c010e0d8>] (unwind_backtrace) from [<c010beac>] (show_stack+0x10/0x14)
[<c010beac>] (show_stack) from [<c017401c>] (register_lock_class+0x4f4/0x55c)
[<c017401c>] (register_lock_class) from [<c0176fe0>] (__lock_acquire+0x74/0x1938)
[<c0176fe0>] (__lock_acquire) from [<c0178cfc>] (lock_acquire+0xfc/0x23c)
[<c0178cfc>] (lock_acquire) from [<c08aa2f8>] (mutex_lock_nested+0x50/0x3b0)
[<c08aa2f8>] (mutex_lock_nested) from [<c05f5bf8>] (rtl8187_start+0x2c/0xd54)
[<c05f5bf8>] (rtl8187_start) from [<c082dea0>] (drv_start+0xa8/0x320)
[<c082dea0>] (drv_start) from [<c084d1d4>] (ieee80211_do_open+0x2bc/0x8e4)
[<c084d1d4>] (ieee80211_do_open) from [<c069be94>] (__dev_open+0xb8/0x120)
[<c069be94>] (__dev_open) from [<c069c11c>] (__dev_change_flags+0x88/0x14c)
[<c069c11c>] (__dev_change_flags) from [<c069c1f8>] (dev_change_flags+0x18/0x48)
[<c069c1f8>] (dev_change_flags) from [<c0710b08>] (devinet_ioctl+0x738/0x840)
[<c0710b08>] (devinet_ioctl) from [<c067925c>] (sock_ioctl+0x164/0x2f4)
[<c067925c>] (sock_ioctl) from [<c02883f8>] (do_vfs_ioctl+0x8c/0x9d0)
[<c02883f8>] (do_vfs_ioctl) from [<c0288da8>] (SyS_ioctl+0x6c/0x7c)
[<c0288da8>] (SyS_ioctl) from [<c0107760>] (ret_fast_syscall+0x0/0x1c)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cd1ec000
[00000000] *pgd=8d1de831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
task: ce73eec0 task.stack: cd1ea000
PC is at mutex_lock_nested+0xe8/0x3b0
LR is at mutex_lock_nested+0xd0/0x3b0
Cc: stable@vger.kernel.org
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 30ce4d1903e1d8a7ccd110860a5eef3c638ed8be ]
missed it in "kill struct filename.separate" several years ago.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 15deb080a6087b73089139569558965750e69d67 ]
When loadparm is set in reipl parm block, the kernel should also set
DIAG308_FLAGS_LP_VALID flag.
This fixes loadparm ignoring during z/VM fcp -> ccw reipl and kvm direct
boot -> ccw reipl.
Cc: <stable@vger.kernel.org>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 0cf1e05157b9e5530dcc3ca9fec9bf617fc93375 ]
On an Output queue, both EMPTY and PENDING buffer states imply that the
buffer is ready for completion-processing by the upper-layer drivers.
So for a non-QEBSM Output queue, get_buf_states() merges mixed
batches of PENDING and EMPTY buffers into one large batch of EMPTY
buffers. The upper-layer driver (ie. qeth) later distuingishes PENDING
from EMPTY by inspecting the slsb_state for
QDIO_OUTBUF_STATE_FLAG_PENDING.
But the merge logic in get_buf_states() contains a bug that causes us to
erronously also merge ERROR buffers into such a batch of EMPTY buffers
(ERROR is 0xaf, EMPTY is 0xa1; so ERROR & EMPTY == EMPTY).
Effectively, most outbound ERROR buffers are currently discarded
silently and processed as if they had succeeded.
Note that this affects _all_ non-QEBSM device types, not just IQD with CQ.
Fix it by explicitly spelling out the exact conditions for merging.
For extracting the "get initial state" part out of the loop, this relies
on the fact that get_buf_states() is never called with a count of 0. The
QEBSM path already strictly requires this, and the two callers with
variable 'count' make sure of it.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit dae55b6fef58530c13df074bcc182c096609339e ]
Immediate retry of EQBS after CCQ 96 means that we potentially misreport
the state of buffers inspected during the first EQBS call.
This occurs when
1. the first EQBS finds all inspected buffers still in the initial state
set by the driver (ie INPUT EMPTY or OUTPUT PRIMED),
2. the EQBS terminates early with CCQ 96, and
3. by the time that the second EQBS comes around, the state of those
previously inspected buffers has changed.
If the state reported by the second EQBS is 'driver-owned', all we know
is that the previous buffers are driver-owned now as well. But we can't
tell if they all have the same state. So for instance
- the second EQBS reports OUTPUT EMPTY, but any number of the previous
buffers could be OUTPUT ERROR by now,
- the second EQBS reports OUTPUT ERROR, but any number of the previous
buffers could be OUTPUT EMPTY by now.
Effectively, this can result in both over- and underreporting of errors.
If the state reported by the second EQBS is 'HW-owned', that doesn't
guarantee that the previous buffers have not been switched to
driver-owned in the mean time. So for instance
- the second EQBS reports INPUT EMPTY, but any number of the previous
buffers could be INPUT PRIMED (or INPUT ERROR) by now.
This would result in failure to process pending work on the queue. If
it's the final check before yielding initiative, this can cause
a (temporary) queue stall due to IRQ avoidance.
Fixes: 25f269f17316 ("[S390] qdio: EQBS retry after CCQ 96")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c02216acf4177c4411d33735c81cad687790fa59 ]
In randconfig testing, we sometimes get this warning:
drivers/gpu/drm/radeon/radeon_object.c: In function 'radeon_bo_create':
drivers/gpu/drm/radeon/radeon_object.c:242:2: error: #warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance thanks to write-combining [-Werror=cpp]
#warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance \
This is rather annoying since almost all other code produces no build-time
output unless we have found a real bug. We already fixed this in the
amdgpu driver in commit 31bb90f1cd08 ("drm/amdgpu: shut up #warning for
compile testing") by adding a CONFIG_COMPILE_TEST check last year and
agreed to do the same here, but both Michel and I then forgot about it
until I came across the issue again now.
For stable kernels, as this is one of very few remaining randconfig
warnings in 4.14.
Cc: stable@vger.kernel.org
Link: https://patchwork.kernel.org/patch/9550009/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 615b2665fd20c327b631ff1e79426775de748094 ]
As found by the ubsan checker, the value of the 'index' variable can be
out of range for the bc[] array:
UBSAN: Undefined behaviour in arch/parisc/kernel/drivers.c:655:21
index 6 is out of range for type 'char [6]'
Backtrace:
[<104fa850>] __ubsan_handle_out_of_bounds+0x68/0x80
[<1019d83c>] check_parent+0xc0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019d86c>] check_parent+0xf0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019d938>] descend_children+0x4c/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019cffc>] hwpath_to_device+0xa4/0xc4
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
