kernel/tools/testing/selftests/net/bareudp.sh, branch linux-rolling-stable

selftests: net: use BASH for bareudp testing

2025-12-01T10:46:03Z

[ Upstream commit 9311e9540a8b406d9f028aa87fb072a3819d4c82 ] In bareudp.sh, this script uses /bin/sh and it will load another lib.sh BASH script at the very beginning. But on some operating systems like Ubuntu, /bin/sh is actually pointed to DASH, thus it will try to run BASH commands with DASH and consequently leads to syntax issues: # ./bareudp.sh: 4: ./lib.sh: Bad substitution # ./bareudp.sh: 5: ./lib.sh: source: not found # ./bareudp.sh: 24: ./lib.sh: Syntax error: "(" unexpected Fix this by explicitly using BASH for bareudp.sh. This fixes test execution failures on systems where /bin/sh is not BASH. Reported-by: Edoardo Canepa Link: https://bugs.launchpad.net/bugs/2129812 Signed-off-by: Po-Hsu Lin Reviewed-by: Przemek Kitszel Link: https://patch.msgid.link/20251027095710.2036108-2-po-hsu.lin@canonical.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

selftests: net: use setup_ns for bareudp testing

2025-05-13T01:10:55Z

Switch bareudp testing to use setup_ns, which sets up rp_filter by default. This allows us to remove the manual rp_filter configuration from the script. Additionally, since setup_ns handles namespace naming and cleanup, we no longer need a separate cleanup function. We also move the trap setup earlier in the script, before the test setup begins. Signed-off-by: Hangbin Liu Reviewed-by: Simon Horman Link: https://patch.msgid.link/20250508081910.84216-4-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski

selftests: set conf.all.rp_filter=0 in bareudp.sh

2020-11-13T00:14:38Z

When working on the rp_filter problem, I didn't realise that disabling it on the network devices didn't cover all cases: rp_filter could also be enabled globally in the namespace, in which case it would drop packets, even if the net device has rp_filter=0. Fixes: 1ccd58331f6f ("selftests: disable rp_filter when testing bareudp") Fixes: bbbc7aa45eef ("selftests: add test script for bareudp tunnels") Signed-off-by: Guillaume Nault Link: https://lore.kernel.org/r/f2d459346471f163b239aa9d63ce3e2ba9c62895.1605107012.git.gnault@redhat.com Signed-off-by: Jakub Kicinski

selftests: disable rp_filter when testing bareudp

2020-11-10T23:14:19Z

Some systems have rp_filter=1 as default configuration. This breaks bareudp.sh as the intermediate namespaces handle part of the routing with regular IPv4 routes but the reverse path is done with tc (flower/tunnel_key/mirred). Signed-off-by: Guillaume Nault Link: https://lore.kernel.org/r/28140b7d20161e4f766b558018fe2718f9bc1117.1604767577.git.gnault@redhat.com Signed-off-by: Jakub Kicinski

selftests: add test script for bareudp tunnels

2020-11-02T23:23:27Z

Test different encapsulation modes of the bareudp module: * Unicast MPLS, * IPv4 only, * IPv4 in multiproto mode (that is, IPv4 and IPv6), * IPv6. Each mode is tested with both an IPv4 and an IPv6 underlay. v2: * Add build dependencies in config file (Willem de Bruijn). * The MPLS test now uses its own IP addresses. This minimises the amount of cleanup between tests and simplifies the script. * Verify that iproute2 supports bareudp tunnels before running the script (and other minor usability improvements). Signed-off-by: Guillaume Nault Link: https://lore.kernel.org/r/8abc0e58f8a7eeb404f82466505a73110bc43ab8.1604088587.git.gnault@redhat.com Signed-off-by: Jakub Kicinski