kernel/sound/soc/codecs/rt1011.h, branch linux-6.2.y

ASoC: rt1011: revert 'I2S Reference' to SOC_ENUM_EXT

2021-11-12T18:16:41Z

Revert 'I2S Reference' to SOC_ENUM_EXT because the settings are specific for some platforms, the default setting for 'I2S Reference' does nothing, only some SoC platform need to configure it. Previous 'I2S Reference' in SOC_ENUM format only toggles one bit of RT1011_TDM1_SET_1 register, which isn't enough for specific platform. Signed-off-by: Jack Yu Link: https://lore.kernel.org/r/20211111091705.20879-1-jack.yu@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: Fix 'I2S Reference' enum control

2021-10-13T15:26:15Z

There are several things the patch adding the support for 'I2S Reference' got wrong: - "None" selection is in fact equals to last selected reference - The custom put overrides RX/TX len, TDM slot sizes, etc - the enum is useless in most part for the reference tracking - there is no need for EXT control as there is a single bit in RT1011_TDM1_SET_1 register (bit 7) which selects the reference - it was using ucontrol->value.integer.value[0] in the put/get callbacks which causesed access to 'I2S Reference' enum with alsamixer to fail Complements: c3de683c4d1d ("ASoC: rt1011: Fix 'I2S Reference' enum control caused error") Signed-off-by: Peter Ujfalusi Link: https://lore.kernel.org/r/20211013123300.11095-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown

ASoC: rt1011: add i2s reference control for rt1011

2021-09-13T00:59:19Z

Add i2s reference control for rt1011 amp. Signed-off-by: Jack Yu Link: https://lore.kernel.org/r/20210906101208.11585-1-jack.yu@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: remove pack_id check in rt1011

2021-04-08T14:08:49Z

For latest design, different package could use the same setting, therefore the check of pack_id will no longer be used. Signed-off-by: Jack Yu Link: https://lore.kernel.org/r/4cbe1cd3b8664140889132464c7dee7b@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: set the different setting for QFN/WLCSP package

2020-01-17T15:30:31Z

The QFN package is a new one. There is a different initial setting to the chip of QFN and WLCSP package. Signed-off-by: Shuming Fan Link: https://lore.kernel.org/r/20200116091854.18095-1-shumingf@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: Read and apply r0 and temperature device property

2019-10-16T12:56:58Z

Typically, the r0 (calibration data) and temperature were measured in the factory. This information is written into the non-volatile area where keeps data whether factory reset or OS update. In Chromium OS case, the coreboot will read the info from VPD and create the device property for each rt1011. Signed-off-by: Shuming Fan Tested-By: Cheng-Yi Chiang Link: https://lore.kernel.org/r/20191016085845.11672-1-shumingf@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: set tx/rx slots from tx/rx_mask in TDM case

2019-10-16T12:55:43Z

The TX/RX slot configuration use tx/rx_mask which requested by the machine driver. Signed-off-by: Shuming Fan Link: https://lore.kernel.org/r/20191016085754.11614-1-shumingf@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: Add a flag for the R0 calibration test

2019-08-07T13:19:13Z

The factory test needs to know whether the calibration completed. This flag helps to confirm the calibration completed or not. Signed-off-by: Shuming Fan Link: https://lore.kernel.org/r/20190806091459.14382-1-shumingf@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: Add R0 temperature and TDM1 ADC2DAT Swap control

2019-08-07T13:18:55Z

- The user level application could set the R0 temperature after booting system. The degree Celsius of R0 temperature store in the non-volatile space when doing R0 calibration. - TDM1 ADC2DAT Swap controls use to control TDM slot2/3 data Signed-off-by: Shuming Fan Link: https://lore.kernel.org/r/20190806091435.14329-1-shumingf@realtek.com Signed-off-by: Mark Brown

ASoC: rt1011: Add RT1011 amplifier driver

2019-06-04T14:09:39Z

This is the initial amplifier driver for rt1011. Signed-off-by: Shuming Fan Signed-off-by: Mark Brown