kernel/net/bluetooth/hci_request.c, branch linux-5.1.y

Bluetooth: Ignore CC events not matching the last HCI command

2019-05-31T13:43:16Z

[ Upstream commit f80c5dad7b6467b884c445ffea45985793b4b2d0 ] This commit makes the kernel not send the next queued HCI command until a command complete arrives for the last HCI command sent to the controller. This change avoids a problem with some buggy controllers (seen on two SKUs of QCA9377) that send an extra command complete event for the previous command after the kernel had already sent a new HCI command to the controller. The problem was reproduced when starting an active scanning procedure, where an extra command complete event arrives for the LE_SET_RANDOM_ADDR command. When this happends the kernel ends up not processing the command complete for the following commmand, LE_SET_SCAN_PARAM, and ultimately behaving as if a passive scanning procedure was being performed, when in fact controller is performing an active scanning procedure. This makes it impossible to discover BLE devices as no device found events are sent to userspace. This problem is reproducible on 100% of the attempts on the affected controllers. The extra command complete event can be seen at timestamp 27.420131 on the btmon logs bellow. Bluetooth monitor ver 5.50 = Note: Linux version 5.0.0+ (x86_64) 0.352340 = Note: Bluetooth subsystem version 2.22 0.352343 = New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344 = Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345 = Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346 @ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347 @ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366 @ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164 @ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310 Address type: 0x06 LE Public LE Random < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496 Address: 15:60:F2:91:B2:24 (Non-Resolvable) > HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244 Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) > HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) > HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059 Start Discovery (0x0023) plen 1 Status: Success (0x00) Address type: 0x06 LE Public LE Random @ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) Signed-off-by: João Paulo Rechi Vita Signed-off-by: Marcel Holtmann Signed-off-by: Sasha Levin

Bluetooth: clean an indentation issue, remove extraneous space

2018-12-18T23:44:01Z

Trivial fix to clean up an indentation issue Signed-off-by: Colin Ian King Signed-off-by: Marcel Holtmann

Bluetooth: Implement secondary advertising on different PHYs

2018-07-30T11:44:53Z

This patch adds support for advertising in primary and secondary channel on different PHYs. User can add the phy preference in the flag based on which phy type will be added in extended advertising parameter would be set. @ MGMT Command: Add Advertising (0x003e) plen 11 Instance: 1 Flags: 0x00000200 Advertise in CODED on Secondary channel Duration: 0 Timeout: 0 Advertising data length: 0 Scan response length: 0 < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0000 Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE Coded (0x03) Secondary max skip: 0x00 Secondary PHY: LE Coded (0x03) SID: 0x00 Scan request notifications: Disabled (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Implement Set ADV set random address

2018-07-30T11:44:53Z

This basically sets the random address for the adv instance Random address can be set only if the instance is created which is done in Set ext adv param. Random address and rpa expire timer and flags have been added to adv instance which will be used when the respective instance is scheduled. This introduces a hci_get_random_address() which returns the own address type and random address (rpa or nrpa) based on the instance flags and hdev flags. New function is required since own address type should be known before setting adv params but address can be set only after setting params. < HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7 Advertising handle: 0x00 Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56) > HCI Event: Command Complete (0x0e) plen 4 LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Implement disable and removal of adv instance

2018-07-30T11:44:53Z

If ext adv is enabled then use ext adv to disable as well. Also remove the adv set during LE disable. < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Use Set ext adv/scan rsp data if controller supports

2018-07-30T11:44:52Z

This patch implements Set Ext Adv data and Set Ext Scan rsp data if controller support extended advertising. Currently the operation is set as Complete data and fragment preference is set as no fragment < HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35 Handle: 0x00 Operation: Complete extended advertising data (0x03) Fragment preference: Minimize fragmentation (0x01) Data length: 0x15 16-bit Service UUIDs (complete): 2 entries Heart Rate (0x180d) Battery Service (0x180f) Name (complete): Test LE Company: Google (224) Data: 0102 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Data (0x08|0x0037) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Impmlement extended adv enable

2018-07-30T11:44:52Z

This patch basically replaces legacy adv with extended adv based on the controller support. Currently there is no design change. ie only one adv set will be enabled at a time. This also adds tx_power in instance and store whatever returns from Set_ext_parameter, use the same in adv data as well. For instance 0 tx_power is stored in hdev only. < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0010 Use legacy advertising PDUs: ADV_NONCONN_IND Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE 1M (0x01) Secondary max skip: 0x00 Secondary PHY: LE 1M (0x01) SID: 0x00 Scan request notifications: Disabled (0x00) > HCI Event: Command Complete (0x0e) plen 5 LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1 Status: Success (0x00) TX power (selected): 7 dbm (0x07) < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6 Extended advertising: Enabled (0x01) Number of sets: 1 (0x01) Entry 0 Handle: 0x00 Duration: 0 ms (0x00) Max ext adv events: 0 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Set Scan PHYs based on selected PHYs by user

2018-07-30T11:44:52Z

Use the PHYs selected in Set Phy Configuration management command while scanning. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x05 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Entry 1: LE Coded Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Use extended scanning if controller supports

2018-07-06T20:41:17Z

This implements Set extended scan param and set extended scan enable commands and use it for start LE scan based on controller support. The new features added in these commands are setting of new PHY for scanning and setting of scan duration. Both features are disabled for now, meaning only 1M PHY is set and scan duration is set to 0 which means that scanning will be done untill scan disable is called. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Introduce helpers for LE set scan start and complete

2018-07-06T20:41:17Z

Introduce a helper hci_req_start_scan() which starts an LE scan and call it from passive_Scan() and active_scan(). There is not functionality change in this patch. This is basically done to enable extended scanning if the controller supports which will be done in the subsequent patch Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann