kernel/include/net/bluetooth/hci.h, branch linux-5.2.y

Bluetooth: Ignore CC events not matching the last HCI command

2019-05-05T17:29:04Z

This commit makes the kernel not send the next queued HCI command until a command complete arrives for the last HCI command sent to the controller. This change avoids a problem with some buggy controllers (seen on two SKUs of QCA9377) that send an extra command complete event for the previous command after the kernel had already sent a new HCI command to the controller. The problem was reproduced when starting an active scanning procedure, where an extra command complete event arrives for the LE_SET_RANDOM_ADDR command. When this happends the kernel ends up not processing the command complete for the following commmand, LE_SET_SCAN_PARAM, and ultimately behaving as if a passive scanning procedure was being performed, when in fact controller is performing an active scanning procedure. This makes it impossible to discover BLE devices as no device found events are sent to userspace. This problem is reproducible on 100% of the attempts on the affected controllers. The extra command complete event can be seen at timestamp 27.420131 on the btmon logs bellow. Bluetooth monitor ver 5.50 = Note: Linux version 5.0.0+ (x86_64) 0.352340 = Note: Bluetooth subsystem version 2.22 0.352343 = New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344 = Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345 = Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346 @ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347 @ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366 @ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164 @ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310 Address type: 0x06 LE Public LE Random < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496 Address: 15:60:F2:91:B2:24 (Non-Resolvable) > HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244 Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) > HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) > HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059 Start Discovery (0x0023) plen 1 Status: Success (0x00) Address type: 0x06 LE Public LE Random @ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) Signed-off-by: João Paulo Rechi Vita Signed-off-by: Marcel Holtmann

Bluetooth: Add quirk for reading BD_ADDR from fwnode property

2019-02-26T09:08:26Z

Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve the public Bluetooth address from the firmware node property 'local-bd-address'. If quirk is set and the property does not exist or is invalid the controller is marked as unconfigured. Signed-off-by: Matthias Kaehlcke Reviewed-by: Balakrishna Godavarthi Tested-by: Balakrishna Godavarthi Signed-off-by: Marcel Holtmann

Bluetooth: Add definitions and track LE resolve list modification

2018-09-27T10:38:52Z

Add the definitions for adding entries to the LE resolve list and removing entries from the LE resolve list. When the LE resolve list gets changed via HCI commands make sure that the internal storage of the resolve list entries gets updated. Signed-off-by: Ankit Navik Signed-off-by: Marcel Holtmann

Bluetooth: Add definitions for LE set address resolution

2018-08-10T14:57:57Z

Add the definitions for LE address resolution enable HCI commands. When the LE address resolution enable gets changed via HCI commands make sure that flag gets updated. Signed-off-by: Ankit Navik Signed-off-by: Marcel Holtmann

Bluetooth: btqca: Introduce HCI_EV_VENDOR and use it

2018-08-06T18:25:05Z

Using HCI_VENDOR_PKT for vendor specific events does work since it has also the value 0xff, but it is actually the packet type indicator constant and not the event constant. So introduce HCI_EV_VENDOR and use it. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg

Bluetooth: Add new quirk for non-persistent setup settings

2018-07-30T12:00:15Z

Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that runs setup() after every open() and not just after the first open(). Signed-off-by: Sean Wang Signed-off-by: Marcel Holtmann

Bluetooth: Implement secondary advertising on different PHYs

2018-07-30T11:44:53Z

This patch adds support for advertising in primary and secondary channel on different PHYs. User can add the phy preference in the flag based on which phy type will be added in extended advertising parameter would be set. @ MGMT Command: Add Advertising (0x003e) plen 11 Instance: 1 Flags: 0x00000200 Advertise in CODED on Secondary channel Duration: 0 Timeout: 0 Advertising data length: 0 Scan response length: 0 < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0000 Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE Coded (0x03) Secondary max skip: 0x00 Secondary PHY: LE Coded (0x03) SID: 0x00 Scan request notifications: Disabled (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Handle ADv set terminated event

2018-07-30T11:44:53Z

This event comes after connection complete event for incoming connections. Since we now have different random address for each instance, conn resp address is assigned from this event. As of now only connection part is handled as we are not enabling duration or max num of events while starting ext adv. Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Implement Set ADV set random address

2018-07-30T11:44:53Z

This basically sets the random address for the adv instance Random address can be set only if the instance is created which is done in Set ext adv param. Random address and rpa expire timer and flags have been added to adv instance which will be used when the respective instance is scheduled. This introduces a hci_get_random_address() which returns the own address type and random address (rpa or nrpa) based on the instance flags and hdev flags. New function is required since own address type should be known before setting adv params but address can be set only after setting params. < HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7 Advertising handle: 0x00 Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56) > HCI Event: Command Complete (0x0e) plen 4 LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann

Bluetooth: Implement disable and removal of adv instance

2018-07-30T11:44:53Z

If ext adv is enabled then use ext adv to disable as well. Also remove the adv set during LE disable. < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery Signed-off-by: Marcel Holtmann