kernel/include/linux/ssb/ssb.h, branch linux-2.6.39.y

ssb: extract indexes for power tables

2010-12-02T19:37:00Z

Signed-off-by: Rafał Miłecki Acked-by: Michael Buesch Signed-off-by: John W. Linville

ssb: remove the ssb DMA API

2010-06-04T20:00:42Z

Now they are unnecessary. We can use the generic DMA API with any bus. Signed-off-by: FUJITA Tomonori Cc: Michael Buesch Cc: Gary Zambrano Cc: Stefano Brivio Cc: Larry Finger Cc: John W. Linville Cc: David S. Miller Signed-off-by: Andrew Morton Signed-off-by: John W. Linville

ssb: add dma_dev to ssb_device structure

2010-06-04T20:00:41Z

Add dma_dev, a pointer to struct device, to struct ssb_device. We pass it to the generic DMA API with SSB_BUSTYPE_PCI and SSB_BUSTYPE_SSB. ssb_devices_register() sets up it properly. This is preparation for replacing the ssb bus specific DMA API (ssb_dma_*) with the generic DMA API. Signed-off-by: FUJITA Tomonori Acked-by: Michael Buesch Cc: Gary Zambrano Cc: Stefano Brivio Cc: Larry Finger Cc: John W. Linville Acked-by: David S. Miller Signed-off-by: Andrew Morton Signed-off-by: John W. Linville

ssb: Look for SPROM at different offset on higher rev CC

2010-04-26T17:51:08Z

Our offset handling becomes even a little more hackish now. For some reason I do not understand all offsets as inrelative. It assumes base offset is 0x1000 but it will work for now as we make offsets relative anyway by removing base 0x1000. Should be cleaner however. Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville

ssb: do not read SPROM if it does not exist

2010-04-26T17:50:54Z

Attempting to read registers that don't exist on the SSB bus can cause hangs on some boxes. At least some b43 devices are 'in the wild' that don't have SPROMs at all. When the SSB bus support loads, it attempts to read these (non-existant) SPROMs and causes hard hangs on the box -- no console output, etc. This patch adds some intelligence to determine whether or not the SPROM is present before attempting to read it. This avoids those hard hangs on those devices with no SPROM attached to their SSB bus. The SSB-attached devices (e.g. b43, et al.) won't work, but at least the box will survive to test further patches. :-) Signed-off-by: John W. Linville Signed-off-by: Rafał Miłecki Cc: Larry Finger Cc: Michael Buesch

ssb: Put host pointers into a union

2009-10-27T20:47:55Z

This slightly shrinks the structure. Signed-off-by: Michael Buesch Signed-off-by: John W. Linville

ssb: Implement SDIO host bus support

2009-09-09T15:19:00Z

Add support for communicating with a Sonics Silicon Backplane through a SDIO interface, as found in the Nintendo Wii WLAN daughter card. The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with a SDIO host interface. Signed-off-by: Albert Herranz Signed-off-by: Michael Buesch Signed-off-by: John W. Linville

ssb: Implement the remaining rev.8 SPROM vars needed for LP-PHY

2009-08-14T13:14:02Z

Also add a "SPEX32" macro for extracting 32-bit SPROM variables. Signed-off-by: Gábor Stefanik Signed-off-by: John W. Linville

ssb: Add SPROM fallback support

2009-03-05T19:39:32Z

This adds SSB functionality to register a fallback SPROM image from the architecture setup code. Weird architectures exist that have half-assed SSB devices without SPROM attached to their PCI busses. The architecture can register a fallback SPROM image that is used if no SPROM is found on the SSB device. Signed-off-by: Michael Buesch Cc: Florian Fainelli Signed-off-by: John W. Linville

ssb: Fix DMA-API compilation for non-PCI systems

2008-11-10T21:50:19Z

This fixes compilation of the SSB DMA-API code on non-PCI platforms. Signed-off-by: Michael Buesch Signed-off-by: David S. Miller