kernel/include/linux/mfd/abx500/ab8500-bm.h, branch linux-5.11.y

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 191

2019-05-30T18:29:21Z

Based on 1 normalized pattern(s): licensed under gplv2 extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 99 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Alexios Zavras Reviewed-by: Richard Fontana Reviewed-by: Allison Randal Reviewed-by: Steve Winslow Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190528170027.163048684@linutronix.de Signed-off-by: Greg Kroah-Hartman

power: supply: ab8500: Drop AB8540/9540 support

2018-04-25T21:49:44Z

The AB8540 was an evolved version of the AB8500, but it was never mass produced or put into products, only reference designs exist. The upstream support was never completed and it is unlikely that this will happen so drop the support for now to simplify maintenance of the AB8500. Cc: Loic Pallardy Signed-off-by: Linus Walleij Acked-by: Lee Jones Signed-off-by: Sebastian Reichel

mfd: abx500: Fix spelling mistake: "Celcius" -> "Celsius"

2017-02-13T09:29:41Z

Trivial fix to spelling mistake in MFD headers. Signed-off-by: Colin Ian King Signed-off-by: Lee Jones

power: ab8500_fg.c: Remove unused function

2015-01-21T13:06:48Z

Remove the function ab8500_fg_reinit() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by: Rickard Strandqvist Acked-by: Arnd Bergmann Signed-off-by: Sebastian Reichel

ab8500_btemp: Make ab8500_btemp_get* interfaces public

2013-04-17T00:32:48Z

Make ab8500_btemp_get_temp interface public, export it and also export the ab8500_btemp_get, ab8500_btemp_get_batctrl_temp interfaces, so that the ab8500 hwmon driver can use them. Signed-off-by: Hongbo Zhang Signed-off-by: Anton Vorontsov

ab8500-charger: Add UsbLineCtrl2 reference

2013-03-07T04:35:50Z

When the state of USB Charge detection is changed then the calls use a define for another register in other bank. This change creates a new define for the correct register and removes the magic numbers that are present. Signed-off-by: Marcus Cooper Signed-off-by: Lee Jones Reviewed-by: Hakan BERG Reviewed-by: Jonas ABERG

ab8500-bm: Add support for the new ab8540 platform

2013-03-07T04:35:48Z

Provide AB8540 platform specific information required to run the Battery Management subsystem on AB8540 based devices. For this to happen we see the introduction of separate platform specific data structures and a means in which to process them. Signed-off-by: Lee Jones

ab8500-bm: Add usb power path support

2013-03-07T04:35:46Z

AB8540 supports power path function in USB charging mode for fast power up with dead and weak battery, and it could extend the battery age. When USB charging starts, if the Vbattrue is below than SW cut off voltage, power path and pre-charge should be enabled. If Vbattrue is higher than SW cut off voltage, power path and pre-charge should be disabled. This is to make sure full current to battery charge. At the end of charge, power path should be enable again to reduce charging the battery again. Signed-off-by: Lee Jones

ab8500-charger: Add backup battery charge voltages on the ab8540

2013-03-07T04:35:37Z

Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available. Signed-off-by: Yang QU Signed-off-by: Lee Jones Reviewed-by: Maxime COQUELIN Reviewed-by: Marcus COOPER Tested-by: Xiao Mei ZHANG

ab8500-fg: Add power cut feature for ab8505 and ab8540

2013-03-07T04:35:36Z

Add support for a power cut feature which allows user to configure when ab8505 and ab8540 based platforms should shut down system due to low battery. Signed-off-by: Lee Jones