kernel/include/linux/libata.h, branch linux-2.6.35.y

libata: skip EH autopsy and recovery during suspend

2010-09-20T20:36:32Z

commit e2f3d75fc0e4a0d03c61872bad39ffa2e74a04ff upstream. For some mysterious reason, certain hardware reacts badly to usual EH actions while the system is going for suspend. As the devices won't be needed until the system is resumed, ask EH to skip usual autopsy and recovery and proceed directly to suspend. Signed-off-by: Tejun Heo Tested-by: Stephan Diestelhorst Signed-off-by: Jeff Garzik Signed-off-by: Greg Kroah-Hartman

libata: implement on-demand HPA unlocking

2010-06-02T17:50:10Z

Implement ata_scsi_unlock_native_capacity() which will be called through SCSI layer when block layer notices that partitions on a device extend beyond the end of the device. It requests EH to unlock HPA, waits for completion and returns the current device capacity. This allows libata to unlock HPA on demand instead of having to decide whether to unlock upfront. Unlocking on demand is safer than unlocking by upfront because some BIOSes write private data to the area beyond HPA limit. This was suggested by Ben Hutchings. Signed-off-by: Tejun Heo Suggested-by: Ben Hutchings Signed-off-by: Jeff Garzik

libata: implement dump_id force param

2010-05-25T23:41:19Z

Add dump_id libata.force parameter. If specified, libata dumps full IDENTIFY data during device configuration. This is to aid debugging. Signed-off-by: Tejun Heo Cc: Larry Baker Signed-off-by: Jeff Garzik

libata-sff: make BMDMA optional

2010-05-25T23:41:12Z

Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA. In Kconfig, drivers are grouped into five groups - non-SFF native, SFF w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic fallback / legacy ones. Kconfig and Makefile are reorganized according to the groups and ordered alphabetically inside each group. ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and functions. This increase the binary size slightly when BMDMA is enabled but on both native-only and PIO-only configurations the size is slightly reduced. Either way, the size difference is insignificant. This change is more meaningful to signify the separation between SFF and BMDMA and as a tool to verify the separation. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA init

2010-05-25T23:40:30Z

Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one() from their SFF counterparts. SFF ones no longer try to initialize BMDMA or set PCI master. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA irq handler

2010-05-25T23:40:24Z

Separate out BMDMA irq handler from SFF irq handler. The misnamed host_intr() functions are renamed to ata_sff_port_intr() and ata_bmdma_port_intr(). Common parts are factored into __ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and bmdma interrupt routines. All BMDMA drivers now use ata_bmdma_interrupt() or ata_bmdma_port_intr() while all non-BMDMA SFF ones use ata_sff_interrupt() or ata_sff_port_intr(). For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's used by both SFF and BMDMA drivers. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: ata_sff_irq_clear() is BMDMA specific

2010-05-25T23:40:19Z

ata_sff_irq_clear() is BMDMA specific. Rename it to ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make ->sff_irq_clear() optional. Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and possibly by sata_sil. This should be moved to respective low level drivers later. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: separate out BMDMA qc_issue

2010-05-19T17:38:55Z

Separate out ata_bmdma_qc_issue() from ata_sff_qc_issue() such that ata_sff_qc_issue() only deals with non-BMDMA SFF protocols (PIO and nodata) while ata_bmdma_qc_issue() deals with the BMDMA protocols and uses ata_sff_qc_issue() for non-DMA commands. All the users are updated accordingly. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: prd is BMDMA specific

2010-05-19T17:38:54Z

struct ata_prd and ap->prd are BMDMA specific. Add bmdma_ prefix to them and move them inside CONFIG_ATA_SFF. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik

libata-sff: ata_sff_[dumb_]qc_prep are BMDMA specific

2010-05-19T17:36:50Z

Both qc_prep functions deal only with BMDMA PRD setup and PIO only SFF drivers don't need them. Rename to ata_bmdma_[dumb_]qc_prep() and relocate. All usages are renamed except for pdc_adma and sata_qstor. Those two drivers are not BMDMA drivers and don't need to call BMDMA qc_prep functions. Calls to ata_sff_qc_prep() in the two drivers are removed. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik