kernel/drivers/usb/serial/usb-wwan.h, branch linux-6.18.y

USB: serial: make usb_serial_driver::chars_in_buffer return uint

2021-05-19T08:56:41Z

tty_operations::chars_in_buffer is being switched to return uint. Do the same for usb_serial_driver's chars_in_buffer. Signed-off-by: Jiri Slaby [ johan: amend commit message ] Signed-off-by: Johan Hovold

USB: serial: make usb_serial_driver::write_room return uint

2021-05-19T08:56:40Z

Line disciplines expect a positive value or zero returned from tty->ops->write_room (invoked by tty_write_room). Both of them are being updated to return an unsigned int. Switch also usb_serial_driver::write_room and all its users. Signed-off-by: Jiri Slaby [ johan: amend commit message, drop unrelated comment change ] Signed-off-by: Johan Hovold

USB: serial: add generic support for TIOCSSERIAL

2021-04-08T07:46:02Z

TIOCSSERIAL is a horrid, underspecified, legacy interface which for most serial devices is only useful for setting the close_delay and closing_wait parameters. The closing_wait parameter determines how long to wait for the transfer buffers to drain during close and the default timeout of 30 seconds may not be sufficient at low line speeds. In other cases, when for example flow is stopped, the default timeout may instead be too long. Add generic support for TIOCSSERIAL and TIOCGSERIAL with handling of the three common parameters close_delay, closing_wait and line for the benefit of all USB serial drivers while still allowing drivers to implement further functionality through the existing callbacks. This currently includes a few drivers that report their base baud clock rate even if that is really only of interest when setting custom divisors through the deprecated ASYNC_SPD_CUST interface; an interface which only the FTDI driver actually implements. Some drivers have also been reporting back a fake UART type, something which should no longer be needed and will be dropped by a follow-on patch. Reviewed-by: Greg Kroah-Hartman Signed-off-by: Johan Hovold

USB: serial: make remove callback return void

2021-02-09T12:13:58Z

All usb_serial drivers return 0 in their remove callbacks and driver core ignores the value returned by usb_serial_device_remove(). So change the remove callback to return void and return 0 unconditionally in usb_serial_device_remove(). Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20210208143149.963644-2-uwe@kleine-koenig.org Signed-off-by: Johan Hovold

USB: serial: option: add ZLP support for 0x1bc7/0x9010

2019-12-20T11:07:12Z

Telit FN980 flashing device 0x1bc7/0x9010 requires zero packet to be sent if out data size is is equal to the endpoint max size. Signed-off-by: Daniele Palmas [ johan: switch operands in conditional ] Cc: stable Signed-off-by: Johan Hovold

usb_wwan: switch to ->[sg]et_serial()

2018-10-13T04:50:42Z

Reviewed-by: Johan Hovold Signed-off-by: Al Viro

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

USB: usb_wwan/option: generalize option_send_setup for other drivers

2015-10-09T10:42:40Z

Only the option driver implements the send_setup callback; it uses the SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals on the port. This is not driver-specific though and is needed by other drivers, so move the function to the usb_wwan driver (with formatting tweaks), and replace the callback pointer with a flag that enables the request. Suggested-by: Bjørn Mork Suggested-by: Johan Hovold Signed-off-by: David Ward Signed-off-by: Johan Hovold

USB: usb_wwan: do not resume I/O on closing ports

2014-05-27T22:04:08Z

Use tty-port initialised flag rather than private flag to determine when port is closing down. Since the tty-port flag is set prior to dropping DTR/RTS (when HUPCL is set) this avoid submitting the read urbs when resuming the interface in dtr_rts() only to immediately kill them again in shutdown(). Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

USB: usb_wwan: remove bogus function prototype

2014-05-27T22:04:08Z

The usb_wwan_send_setup() function has never existed. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman