kernel/drivers/usb/core, branch linux-4.16.y

usb: core: message: remove extra endianness conversion in usb_set_isoch_delay

2018-06-16T07:43:43Z

commit 48b73d0fa11aa8613d51f7be61d2fa7f0ab05fd3 upstream. No need to do extra endianness conversion in usb_set_isoch_delay because it is already done in usb_control_msg() Fixes: 886ee36e7205 ("usb: core: add support for USB_REQ_SET_ISOCH_DELAY") Cc: Dmytro Panchenko Cc: Felipe Balbi Cc: stable # v4.16+ Signed-off-by: Ruslan Bilovol Signed-off-by: Greg Kroah-Hartman

USB: Accept bulk endpoints with 1024-byte maxpacket

2018-05-09T07:53:11Z

commit fb5ee84ea72c5f1b6cabdd1c9d6e8648995ca7c6 upstream. Some non-compliant high-speed USB devices have bulk endpoints with a 1024-byte maxpacket size. Although such endpoints don't work with xHCI host controllers, they do work with EHCI controllers. We used to accept these invalid sizes (with a warning), but we no longer do because of an unintentional change introduced by commit aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors"). This patch restores the old behavior, so that people with these peculiar devices can use them without patching their kernels by hand. Signed-off-by: Alan Stern Suggested-by: Elvinas Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors") CC: Signed-off-by: Greg Kroah-Hartman

USB: Increment wakeup count on remote wakeup.

2018-05-01T19:47:20Z

commit 83a62c51ba7b3c0bf45150c4eac7aefc6c785e94 upstream. On chromebooks we depend on wakeup count to identify the wakeup source. But currently USB devices do not increment the wakeup count when they trigger the remote wake. This patch addresses the same. Resume condition is reported differently on USB 2.0 and USB 3.0 devices. On USB 2.0 devices, a wake capable device, if wake enabled, drives resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7). The upstream facing port then sets C_PORT_SUSPEND bit and reports a port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port has resumed before driving the resume signal from the host and C_PORT_SUSPEND is set, then the device attached to the given port might be the reason for the last system wakeup. Increment the wakeup count for the same. On USB 3.0 devices, a function may signal that it wants to exit from device suspend by sending a Function Wake Device Notification to the host (USB3.0 spec section 8.5.6.4) Thus on receiving the Function Wake, increment the wakeup count. Signed-off-by: Ravi Chandra Sadineni Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: core: Add quirk for HP v222w 16GB Mini

2018-05-01T19:47:20Z

commit 3180dabe08e3653bf0a838553905d88f3773f29c upstream. Add DELAY_INIT quirk to fix the following problem with HP v222w 16GB Mini: usb 1-3: unable to read config index 0 descriptor/start: -110 usb 1-3: can't read configurations, error -110 usb 1-3: can't set config #1, error -110 Signed-off-by: Kamil Lulko Signed-off-by: Kuppuswamy Sathyanarayanan Cc: stable Signed-off-by: Greg Kroah-Hartman

USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw

2018-04-24T07:42:52Z

commit 64627388b50158fd24d6ad88132525b95a5ef573 upstream. USB3 hubs don't support global suspend. USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective suspend and resume, they do not support global suspend/resume where the hub downstream facing ports states are not affected. When system enters hibernation it first enters freeze process where only the root hub enters suspend, usb_port_suspend() is not called for other devices, and suspend status flags are not set for them. Other devices are expected to suspend globally. Some external USB3 hubs will suspend the downstream facing port at global suspend. These devices won't be resumed at thaw as the suspend status flag is not set. A USB3 removable hard disk connected through a USB3 hub that won't resume at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71” error, and needs a 60 seconds timeout which causing system hang for 60s before the USB host reset the port for the USB3 removable hard disk to recover. Fix this by always calling usb_port_suspend() during freeze for USB3 devices. Signed-off-by: Zhengjun Xing Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: quirks: add control message delay for 1b1c:1b20

2018-03-06T17:17:34Z

Corsair Strafe RGB keyboard does not respond to usb control messages sometimes and hence generates timeouts. Commit de3af5bf259d ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard") tried to fix those timeouts by adding USB_QUIRK_DELAY_INIT. Unfortunately, even with this quirk timeouts of usb_control_msg() can still be seen, but with a lower frequency (approx. 1 out of 15): [ 29.103520] usb 1-8: string descriptor 0 read error: -110 [ 34.363097] usb 1-8: can't set config #1, error -110 Adding further delays to different locations where usb control messages are issued just moves the timeouts to other locations, e.g.: [ 35.400533] usbhid 1-8:1.0: can't add hid device: -110 [ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110 The only way to reliably avoid those issues is having a pause after each usb control message. In approx. 200 boot cycles no more timeouts were seen. Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary to have the delay in hub_port_connect() after hub_port_init(). The overall boot time seems not to be influenced by these additional delays, even on fast machines and lightweight distributions. Fixes: de3af5bf259d ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard") Cc: stable@vger.kernel.org Signed-off-by: Danilo Krummrich Signed-off-by: Greg Kroah-Hartman

Add delay-init quirk for Corsair K70 RGB keyboards

2018-02-15T19:52:56Z

Following on from this patch: https://lkml.org/lkml/2017/11/3/516, Corsair K70 RGB keyboards also require the DELAY_INIT quirk to start correctly at boot. Device ids found here: usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13 usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 3-3: Product: Corsair K70 RGB Gaming Keyboard Signed-off-by: Jack Stocker Cc: stable Signed-off-by: Greg Kroah-Hartman

vfs: do bulk POLL* -> EPOLL* replacement

2018-02-11T22:34:03Z

This is the mindless scripted replacement of kernel use of POLL* variables as described by Al, done by this script: for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'` for f in $L; do sed -i "-es/^$[^\"]*$$\$/\\1E\\2/" $f; done done with de-mangling cleanups yet to come. NOTE! On almost all architectures, the EPOLL* constants have the same values as the POLL* constants do. But they keyword here is "almost". For various bad reasons they aren't the same, and epoll() doesn't actually work quite correctly in some cases due to this on Sparc et al. The next patch from Al will sort out the final differences, and we should be all done. Scripted-by: Al Viro Signed-off-by: Linus Torvalds

Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2018-02-01T17:40:49Z

Pull USB/PHY updates from Greg KH: "Here is the big USB and PHY driver update for 4.16-rc1. Along with the normally expected XHCI, MUSB, and Gadget driver patches, there are some PHY driver fixes, license cleanups, sysfs attribute cleanups, usbip changes, and a raft of other smaller fixes and additions. Full details are in the shortlog. All of these have been in the linux-next tree for a long time with no reported issues" * tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits) USB: serial: pl2303: new device id for Chilitag USB: misc: fix up some remaining DEVICE_ATTR() usages USB: musb: fix up one odd DEVICE_ATTR() usage USB: atm: fix up some remaining DEVICE_ATTR() usage USB: move many drivers to use DEVICE_ATTR_WO USB: move many drivers to use DEVICE_ATTR_RO USB: move many drivers to use DEVICE_ATTR_RW USB: misc: chaoskey: Use true and false for boolean values USB: storage: remove old wording about how to submit a change USB: storage: remove invalid URL from drivers usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found usbip: list: don't list devices attached to vhci_hcd usbip: prevent bind loops on devices attached to vhci_hcd USB: serial: remove redundant initializations of 'mos_parport' usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc() usb: gadget: compress return logic into one line usbip: vhci_hcd: update 'status' file header and format USB: serial: simple: add Motorola Tetra driver CDC-ACM: apply quirk for card reader usb: option: Add support for FS040U modem ...

Merge branch 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs

2018-01-31T01:58:07Z

Pull poll annotations from Al Viro: "This introduces a __bitwise type for POLL### bitmap, and propagates the annotations through the tree. Most of that stuff is as simple as 'make ->poll() instances return __poll_t and do the same to local variables used to hold the future return value'. Some of the obvious brainos found in process are fixed (e.g. POLLIN misspelled as POLL_IN). At that point the amount of sparse warnings is low and most of them are for genuine bugs - e.g. ->poll() instance deciding to return -EINVAL instead of a bitmap. I hadn't touched those in this series - it's large enough as it is. Another problem it has caught was eventpoll() ABI mess; select.c and eventpoll.c assumed that corresponding POLL### and EPOLL### were equal. That's true for some, but not all of them - EPOLL### are arch-independent, but POLL### are not. The last commit in this series separates userland POLL### values from the (now arch-independent) kernel-side ones, converting between them in the few places where they are copied to/from userland. AFAICS, this is the least disruptive fix preserving poll(2) ABI and making epoll() work on all architectures. As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and it will trigger only on what would've triggered EPOLLWRBAND on other architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered at all on sparc. With this patch they should work consistently on all architectures" * 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits) make kernel-side POLL... arch-independent eventpoll: no need to mask the result of epi_item_poll() again eventpoll: constify struct epoll_event pointers debugging printk in sg_poll() uses %x to print POLL... bitmap annotate poll(2) guts 9p: untangle ->poll() mess ->si_band gets POLL... bitmap stored into a user-visible long field ring_buffer_poll_wait() return value used as return value of ->poll() the rest of drivers/*: annotate ->poll() instances media: annotate ->poll() instances fs: annotate ->poll() instances ipc, kernel, mm: annotate ->poll() instances net: annotate ->poll() instances apparmor: annotate ->poll() instances tomoyo: annotate ->poll() instances sound: annotate ->poll() instances acpi: annotate ->poll() instances crypto: annotate ->poll() instances block: annotate ->poll() instances x86: annotate ->poll() instances ...