kernel/drivers/usb/core/hub.c, branch linux-4.16.y

USB: Increment wakeup count on remote wakeup.

2018-05-01T19:47:20Z

commit 83a62c51ba7b3c0bf45150c4eac7aefc6c785e94 upstream. On chromebooks we depend on wakeup count to identify the wakeup source. But currently USB devices do not increment the wakeup count when they trigger the remote wake. This patch addresses the same. Resume condition is reported differently on USB 2.0 and USB 3.0 devices. On USB 2.0 devices, a wake capable device, if wake enabled, drives resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7). The upstream facing port then sets C_PORT_SUSPEND bit and reports a port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port has resumed before driving the resume signal from the host and C_PORT_SUSPEND is set, then the device attached to the given port might be the reason for the last system wakeup. Increment the wakeup count for the same. On USB 3.0 devices, a function may signal that it wants to exit from device suspend by sending a Function Wake Device Notification to the host (USB3.0 spec section 8.5.6.4) Thus on receiving the Function Wake, increment the wakeup count. Signed-off-by: Ravi Chandra Sadineni Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman

Merge 4.15-rc4 into usb-next

2017-12-18T08:08:05Z

We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman

usb: core: add support for USB_REQ_SET_ISOCH_DELAY

2017-12-15T19:45:43Z

USB SS and SSP hubs provide wHubDelay values on their hub descriptor which we should inform the USB Device about. The USB Specification 3.0 explains, on section 9.4.11, how to calculate the value and how to issue the request. Note that a USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default, Address, Configured), we just *chose* to issue it from Address state right after successfully fetching the USB Device Descriptor. Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

usb: core: Fix logging messages with spurious periods after newlines

2017-12-06T08:21:17Z

Using a period after a newline causes bad output. Miscellanea: o Coalesce formats too Signed-off-by: Joe Perches Signed-off-by: Greg Kroah-Hartman

usb: hub: Cycle HUB power when initialization fails

2017-11-28T14:17:49Z

Sometimes the USB device gets confused about the state of the initialization and the connection fails. In particular, the device thinks that it's already set up and running while the host thinks the device still needs to be configured. To work around this issue, power-cycle the hub's output to issue a sort of "reset" to the device. This makes the device restart its state machine and then the initialization succeeds. This fixes problems where the kernel reports a list of errors like this: usb 1-1.3: device not accepting address 19, error -71 The end result is a non-functioning device. After this patch, the sequence becomes like this: usb 1-1.3: new high-speed USB device number 18 using ci_hdrc usb 1-1.3: device not accepting address 18, error -71 usb 1-1.3: new high-speed USB device number 19 using ci_hdrc usb 1-1.3: device not accepting address 19, error -71 usb 1-1-port3: attempt power cycle usb 1-1.3: new high-speed USB device number 21 using ci_hdrc usb-storage 1-1.3:1.2: USB Mass Storage device detected Signed-off-by: Mike Looijmans Acked-by: Alan Stern Cc: stable Signed-off-by: Greg Kroah-Hartman

usb: core: introduce a new usb_get_std_status() helper

2017-11-07T14:47:19Z

This new helper is a simple wrapper around usb_get_status(). This patch is in preparation to adding support for fetching PTM_STATUS types. No functional changes. Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman

USB: core: move existing SPDX tags to top of the file

2017-11-03T09:12:26Z

To match the rest of the kernel, the SPDX tags for the drivers/usb/core/ files are moved to the first line of the file. This makes it more obvious the tag is present as well as making it match the other 12k files in the tree with this location. It also uses // to match the "expected style" as well. Signed-off-by: Greg Kroah-Hartman

Merge 4.14-rc6 into usb-next

2017-10-23T12:24:37Z

We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman

USB: Force disconnect Huawei 4G modem during suspend

2017-10-23T09:32:34Z

When going into S3 suspend, the Acer TravelMate P648-M and P648-G3 laptops immediately wake up 3-4 seconds later for no obvious reason. Unbinding the integrated Huawei 4G LTE modem before suspend avoids the issue, even though we are not using the modem at all (checked from rescue.target/runlevel1). The problem also occurs when the option and cdc-ether modem drivers aren't loaded; it reproduces just with the base usb driver. Under Windows the system can suspend fine. Seeking a better fix, we've tried a lot of things, including: - Check that the device's power/wakeup is disabled - Check that remote wakeup is off at the USB level - All the quirks in drivers/usb/core/quirks.c e.g. USB_QUIRK_RESET_RESUME, USB_QUIRK_RESET, USB_QUIRK_IGNORE_REMOTE_WAKEUP, USB_QUIRK_NO_LPM. but none of that makes any difference. There are no errors in the logs showing any suspend/resume-related issues. When the system wakes up due to the modem, log-wise it appears to be a normal resume. Introduce a quirk to disable the port during suspend when the modem is detected. The modem from the P648-G3 model is: T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=12d1 ProdID=15c3 Rev= 1.02 S: Manufacturer=Huawei Technologies Co., Ltd. S: Product=HUAWEI Mobile S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr= 2mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver= E: Ad=82(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver= E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver= E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver= E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I: If#= 3 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=16 Driver= E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=2ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver= E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms C:* #Ifs= 6 Cfg#= 2 Atr=a0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms C: #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr= 2mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver= E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=2ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver= I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver= E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Based on an earlier patch by Chris Chiu. Signed-off-by: Daniel Drake Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman

usb: hub: Allow reset retry for USB2 devices on connect bounce

2017-10-19T07:49:11Z

If the connect status change is set during reset signaling, but the status remains connected just retry port reset. This solves an issue with connecting a 90W HP Thunderbolt 3 dock with a Lenovo Carbon x1 (5th generation) which causes a 30min loop of a high speed device being re-discovererd before usb ports starts working. [...] [ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd [ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd [ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd [...] This is caused by a high speed device that doesn't successfully go to the enabled state after the second port reset. Instead the connection bounces (connected, with connect status change), bailing out completely from enumeration just to restart from scratch. Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332 Cc: Stable Signed-off-by: Mathias Nyman Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman