kernel/drivers/tty/serial, branch linux-rolling-stable

serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done

2026-03-04T12:20:42Z

[ Upstream commit a5fd8945a478ff9be14812693891d7c9b4185a50 ] Clear rx_running flag only after DMA teardown polling completes. In the previous implementation the flag was being cleared while hardware teardown was still in progress, creating a mismatch between software state (flag = 0, "ready") and hardware state (still terminating). Signed-off-by: Moteen Shah Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: 8250: 8250_omap.c: Add support for handling UART error conditions

2026-03-04T12:20:41Z

[ Upstream commit 623b07b370e9963122d167e04fdc1dc713ebfbaf ] The DMA IRQ handler does not accounts for the overrun(OE) or any other errors being reported by the IP before triggering a DMA transaction which leads to the interrupts not being handled resulting into an IRQ storm. The way to handle OE is to: 1. Reset the RX FIFO. 2. Read the UART_RESUME register, which clears the internal flag Earlier, the driver issued DMA transations even in case of OE which shouldn't be done according to the OE handling mechanism mentioned above, as we are resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During Receive" [0]. [0] https://www.ti.com/lit/pdf/spruiu1 Signed-off-by: Moteen Shah Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: rsci: Add set_rtrg() callback

2026-03-04T12:20:39Z

[ Upstream commit b346e5d7dbf6696176417923c49838a1beb1d785 ] The rtrg variable is populated in sci_init_single() for RZ/T2H. Add set_rtrg() callback for setting the rtrg value. Signed-off-by: Biju Das Tested-by: Lad Prabhakar Link: https://patch.msgid.link/20251129164325.209213-4-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: 8250_dw: handle clock enable errors in runtime_resume

2026-03-04T12:20:38Z

[ Upstream commit d31228143a489ba6ba797896a07541ce06828c09 ] Add error checking for clk_prepare_enable() calls in dw8250_runtime_resume(). Currently if either clock fails to enable, the function returns success while leaving clocks in inconsistent state. This change implements comprehensive error handling by checking the return values of both clk_prepare_enable() calls. If the second clock enable operation fails after the first clock has already been successfully enabled, the code now properly cleans up by disabling and unpreparing the first clock before returning. The error code is then propagated to the caller, ensuring that clock enable failures are properly reported rather than being silently ignored. Signed-off-by: Artem Shimko Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: SH_SCI: improve "DMA support" prompt

2026-02-26T23:01:24Z

[ Upstream commit 93bb95a11238d66a4c9aa6eabf9774b073a5895c ] Having a prompt of "DMA support" suddenly appear during a "make oldconfig" can be confusing. Add a little helpful text to the prompt message. Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.") Signed-off-by: Randy Dunlap Reviewed-by: Geert Uytterhoeven Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: imx: change SERIAL_IMX_CONSOLE to bool

2026-02-26T23:01:24Z

[ Upstream commit 79527d86ba91c2d9354832d19fd12b3baa66bd10 ] SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX). It does not build a separate console driver file, so it can't be built as a module since it isn't built at all. Change the Kconfig symbol from tristate to bool and update the help text accordingly. Fixes: 0db4f9b91c86 ("tty: serial: imx: enable imx serial console port as module") Signed-off-by: Randy Dunlap Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin

serial: Fix not set tty->port race condition

2026-01-23T16:23:09Z

Revert commit bfc467db60b7 ("serial: remove redundant tty_port_link_device()") because the tty_port_link_device() is not redundant: the tty->port has to be confured before we call uart_configure_port(), otherwise user-space can open console without TTY linked to the driver. This tty_port_link_device() was added explicitly to avoid this exact issue in commit fb2b90014d78 ("tty: link tty and port before configuring it as console"), so offending commit basically reverted the fix saying it is redundant without addressing the actual race condition presented there. Reproducible always as tty->port warning on Qualcomm SoC with most of devices disabled, so with very fast boot, and one serial device being the console: printk: legacy console [ttyMSM0] enabled printk: legacy console [ttyMSM0] enabled printk: legacy bootconsole [qcom_geni0] disabled printk: legacy bootconsole [qcom_geni0] disabled ------------[ cut here ]------------ tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver! WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1 Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6 CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT Tainted: [S]=CPU_OUT_OF_SPEC Hardware name: Qualcomm Technologies, Inc. Eliza (DT) ... tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P) tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3)) chrdev_open (fs/char_dev.c:411) do_dentry_open (fs/open.c:962) vfs_open (fs/open.c:1094) do_open (fs/namei.c:4634) path_openat (fs/namei.c:4793) do_filp_open (fs/namei.c:4820) do_sys_openat2 (fs/open.c:1391 (discriminator 3)) ... Starting Network Name Resolution... Apparently the flow with this small Yocto-based ramdisk user-space is: driver (qcom_geni_serial.c): user-space: ============================ =========== qcom_geni_serial_probe() uart_add_one_port() serial_core_register_port() serial_core_add_one_port() uart_configure_port() register_console() | | open console | ... | tty_init_dev() | driver->ports[idx] is NULL | tty_port_register_device_attr_serdev() tty_port_link_device() <- set driver->ports[idx] Fixes: bfc467db60b7 ("serial: remove redundant tty_port_link_device()") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski Reviewed-by: Jiri Slaby Link: https://patch.msgid.link/20260123072139.53293-2-krzysztof.kozlowski@oss.qualcomm.com Signed-off-by: Greg Kroah-Hartman

serial: 8250_pci: Fix broken RS485 for F81504/508/512

2026-01-16T13:29:10Z

Fintek F81504/508/512 can support both RTS_ON_SEND and RTS_AFTER_SEND, but pci_fintek_rs485_supported only announces the former. This makes it impossible to unset SER_RS485_RTS_ON_SEND from userspace because of uart_sanitize_serial_rs485(). Some devices with these chips need RTS low on TX, so they are effectively broken. Fix this by announcing the support for SER_RS485_RTS_AFTER_SEND, similar to commit 068d35a7be65 ("serial: sc16is7xx: announce support for SER_RS485_RTS_ON_SEND"). Fixes: 4afeced55baa ("serial: core: fix sanitizing check for RTS settings") Cc: stable Signed-off-by: Marnix Rijnart Link: https://patch.msgid.link/20260112000931.61703-1-marnix.rijnart@iwell.eu Signed-off-by: Greg Kroah-Hartman

serial: qcom_geni: Fix BT failure regression on RB2 platform

2026-01-16T13:28:49Z

Commit 10904d725f6e ("serial: qcom-geni: Enable PM runtime for serial driver") caused BT init to fail during bootup on the RB2 platform, preventing proper BT initialization. However, BT works correctly after bootup completes. The issue occurs when runtime PM is enabled and uart_add_one_port() is called before wakeup IRQ setup. The uart_add_one_port() call activates the device through runtime PM, which configures GPIOs to the "qup_x" pinmux function during runtime resume. When wakeup IRQ registration happens afterward using dev_pm_set_dedicated_wake_irq(), these GPIOs are reset back to the "gpio" pinmux function, which impacts the RX GPIO and leads to Bluetooth failures. Fix this by ensuring wakeup IRQ setup is completed before calling uart_add_one_port() to prevent the pinmux function conflict. Fixes: 10904d725f6e ("serial: qcom-geni: Enable PM runtime for serial driver") Reported-by: Dmitry Baryshkov Closes: https://lore.kernel.org/all/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com/ Tested-by: Dmitry Baryshkov Reviewed-by: Dmitry Baryshkov Signed-off-by: Praveen Talari Link: https://patch.msgid.link/20260108041006.1874757-1-praveen.talari@oss.qualcomm.com Signed-off-by: Greg Kroah-Hartman

serial: xilinx_uartps: fix rs485 delay_rts_after_send

2025-12-23T10:55:16Z

RTS line control with delay should be triggered when there is no more bytes in kfifo and hardware buffer is empty. Without this patch RTS control is scheduled right after feeding hardware buffer and this is too early. RTS line may change state before hardware buffer is empty. With this patch delayed RTS state change is triggered when function cdns_uart_handle_tx is called from cdns_uart_isr on CDNS_UART_IXR_TXEMPTY exactly when hardware completed transmission Fixes: fccc9d9233f9 ("tty: serial: uartps: Add rs485 support to uartps driver") Cc: stable Link: https://patch.msgid.link/20251221103221.1971125-1-jakub.turek@elsta.tech Signed-off-by: Jakub Turek Signed-off-by: Greg Kroah-Hartman