kernel/drivers/serial/Makefile, branch linux-2.6.26.y

Blackfin serial driver: this driver enable SPORTs on Blackfin emulate UART

2008-04-30T15:29:30Z

Signed-off-by: Bryan Wu Cc: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[MIPS] Alchemy: move UART platform code to its proper place

2008-04-28T16:14:28Z

Move the code registering the Alchemy UART platform devices from drivers/serial/ to its proper place, into the Alchemy platform code. Fix the related Kconfig entry, while at it... Signed-off-by: Sergei Shtylyov Signed-off-by: Ralf Baechle

consoles: polling support, kgdboc

2008-04-17T18:05:37Z

polled console handling support, to access a console in an irq-less way while in debug or irq context. absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled. (which is the default) [ jan.kiszka@siemens.com: lots of cleanups ] [ mingo@elte.hu: redesign, splitups, cleanups. ] Signed-off-by: Jason Wessel Signed-off-by: Ingo Molnar Signed-off-by: Jan Kiszka Reviewed-by: Thomas Gleixner

SC26XX: New serial driver for SC2681 uarts

2008-02-06T18:41:06Z

New serial driver for SC2681/SC2691 uarts. Older SNI RM400 machines are using these chips for onboard serial ports. Signed-off-by: Thomas Bogendoerfer Cc: Ralf Baechle Cc: Alan Cox Cc: Torben Mathiasen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

m68knommu: build support for new ColdFire serial driver

2008-02-01T09:54:03Z

Add build support for new ColdFire serial driver. Signed-off-by: Greg Ungerer Signed-off-by: Linus Torvalds

[POWERPC] qe-uart: add support for Freescale QUICCEngine UART

2008-01-24T01:34:12Z

Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine. Update the Kconfig and Makefile accordingly. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

zs: move to the serial subsystem

2007-07-18T15:38:22Z

This is a reimplementation of the zs driver for the serial subsystem. Any resemblance to the old driver is purely coincidential. ;-) I do hope I got the handling of modem lines right -- better do not tackle me about the issue unless you feel too good... Any users of the old driver: please note the numbers of the serial lines have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has to do with the modem lines mentioned above; basically the port A in a given chip has to be initialised before the port B if you want to use the latter as the serial console (which is usually the case), as operations on modem lines of the serial line associated with the port B access both ports (see the comment at the top of the driver for the details of wiring used). Please update your scripts. This is also the reason each SCC now requests an IRQ once only (as seen in "/proc/interrupts") -- the handler takes care of both ports at once as the line associated with the port B has to take status update interrupts from both ports (and yet the line of the port A takes its own for itself too). The old driver never got it right... Signed-off-by: Maciej W. Rozycki Cc: Ralf Baechle Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

sb1250-duart.c: SB1250 DUART serial support

2007-07-17T17:23:03Z

This is a driver for the SB1250 DUART, a dual serial port implementation included in the Broadcom family of SOCs descending from the SiByte SB1250 MIPS64 chip multiprocessor. It is a new implementation replacing the old-fashioned driver currently present in the linux-mips.org tree. It supports all the usual features one would expect from a(n asynchronous) serial driver, including modem line control (as far as hardware supports it -- there is edge detection logic missing from the DCD and RI lines and the driver does not implement polling of these lines at the moment), the serial console, BREAK transmission and reception, including the magic SysRq. The receive FIFO threshold is not maintained though. The driver was tested with a SWARM board which uses a BCM1250 SOC (which is dual MIPS64 CMP) and has both ports of the single DUART implemented wired externally. Both were tested. Testing included using the ports as terminal lines at 1200bps (which is the ports minimum), 115200bps and a couple of random speeds inbetween. The modem lines were verified to operate correctly. No testing was performed with a use as a network interface, like with SLIP or PPP. Signed-off-by: Maciej W. Rozycki Acked-by: Ralf Baechle Cc: Alan Cox Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

[ARM] 4332/2: KS8695: Serial driver

2007-05-11T21:02:52Z

A driver for the KS8695 internal UART. Based on the 2.6.9 driver from Micrel. Signed-off-by: Andrew Victor Signed-off-by: Russell King

blackfin: serial driver

2007-05-07T19:12:58Z

This patch implements the driver necessary use the Analog Devices Blackfin processor's Serial Port. Signed-off-by: Bryan Wu Cc: Alan Cox Cc: Russell King Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds