kernel/drivers/scsi/libsas, branch linux-6.9.y

scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed

2024-07-25T07:53:37Z

[ Upstream commit ab2068a6fb84751836a84c26ca72b3beb349619d ] The expander phy will be treated as broadcast flutter in the next revalidation after the exp-attached end device probe failed, as follows: [78779.654026] sas: broadcast received: 0 [78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10 [78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed [78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE) [78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached [78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp) [78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found [78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0 [78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0 ... [78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1 [78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19 [78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone [78835.187487] sas: broadcast received: 0 [78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10 [78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed [78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE) [78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05 [78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp) [78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter [78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0 The cause of the problem is that the related ex_phy's attached_sas_addr was not cleared after the end device probe failed, so reset it. Signed-off-by: Xingui Yang Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com Reviewed-by: John Garry Signed-off-by: Martin K. Petersen Signed-off-by: Sasha Levin

ata,scsi: libata-core: Do not leak memory for ata_port struct members

2024-07-05T07:38:07Z

[ Upstream commit f6549f538fe0b2c389e1a7037f4e21039e25137a ] libsas is currently not freeing all the struct ata_port struct members, e.g. ncq_sense_buf for a driver supporting Command Duration Limits (CDL). Add a function, ata_port_free(), that is used to free a ata_port, including its struct members. It makes sense to keep the code related to freeing a ata_port in its own function, which will also free all the struct members of struct ata_port. Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD") Reviewed-by: John Garry Link: https://lore.kernel.org/r/20240629124210.181537-8-cassel@kernel.org Signed-off-by: Niklas Cassel Signed-off-by: Sasha Levin

scsi: libsas: Fix the failure of adding phy with zero-address to port

2024-05-30T07:44:22Z

[ Upstream commit 06036a0a5db34642c5dbe22021a767141f010b7a ] As of commit 7d1d86518118 ("[SCSI] libsas: fix false positive 'device attached' conditions"), reset the phy->entacted_sas_addr address to a zero-address when the link rate is less than 1.5G. Currently we find that when a new device is attached, and the link rate is less than 1.5G, but the device type is not NO_DEVICE, for example: the link rate is SAS_PHY_RESET_IN_PROGRESS and the device type is stp. After setting the phy->entacted_sas_addr address to the zero address, the port will continue to be created for the phy with the zero-address, and other phys with the zero-address will be tried to be added to the new port: [562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached: 0000000000000000 (no device) // phy19 is deleted but still on the parent port's phy_list [562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached [562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached: 0000000000000000 (stp) [562240.062680] port-7:7:0: trying to add phy phy-7:7:19 fails: it's already part of another port Therefore, it should be the same as sas_get_phy_attached_dev(). Only when device_type is SAS_PHY_UNUSED, sas_address is set to the 0 address. Fixes: 7d1d86518118 ("[SCSI] libsas: fix false positive 'device attached' conditions") Signed-off-by: Xingui Yang Link: https://lore.kernel.org/r/20240312141103.31358-5-yangxingui@huawei.com Signed-off-by: Martin K. Petersen Signed-off-by: Sasha Levin

scsi: libsas: Align SMP request allocation to ARCH_DMA_MINALIGN

2024-04-02T01:34:23Z

This series [1] reduced the kmalloc() minimum alignment on arm64 to 8 bytes (from 128). In libsas, this will cause SMP requests to be 8-byte aligned through kmalloc() allocation. However, for hisi_sas hardware, all command addresses must be 16-byte-aligned. Otherwise, the commands fail to be executed. ARCH_DMA_MINALIGN represents the minimum (static) alignment for safe DMA operations, so use ARCH_DMA_MINALIGN as the alignment for SMP request. Link: https://lkml.kernel.org/r/20230612153201.554742-1-catalin.marinas@arm.com [1] Signed-off-by: Yihang Li Link: https://lore.kernel.org/r/20240328090626.621147-1-liyihang9@huawei.com Reviewed-by: Damien Le Moal Reviewed-by: John Garry Reviewed-by: Jason Yan Signed-off-by: Martin K. Petersen

scsi: libsas: Fix disk not being scanned in after being removed

2024-03-10T22:02:54Z

As of commit d8649fc1c5e4 ("scsi: libsas: Do discovery on empty PHY to update PHY info"), do discovery will send a new SMP_DISCOVER and update phy->phy_change_count. We found that if the disk is reconnected and phy change_count changes at this time, the disk scanning process will not be triggered. Therefore, call sas_set_ex_phy() to update the PHY info with the results of the last query. And because the previous phy info will be used when calling sas_unregister_devs_sas_addr(), sas_unregister_devs_sas_addr() should be called before sas_set_ex_phy(). Fixes: d8649fc1c5e4 ("scsi: libsas: Do discovery on empty PHY to update PHY info") Signed-off-by: Xingui Yang Link: https://lore.kernel.org/r/20240307141413.48049-3-yangxingui@huawei.com Reviewed-by: John Garry Signed-off-by: Martin K. Petersen

scsi: libsas: Add a helper sas_get_sas_addr_and_dev_type()

2024-03-10T22:02:53Z

Add a helper to get attached_sas_addr and device type from disc_resp. Suggested-by: John Garry Signed-off-by: Xingui Yang Link: https://lore.kernel.org/r/20240307141413.48049-2-yangxingui@huawei.com Reviewed-by: John Garry Signed-off-by: Martin K. Petersen

scsi: libsas: Declare sas_discover_end_dev() static

2023-09-14T01:06:44Z

sas_discover_end_dev() is defined and used only in sas_discover.c. Define this function as static. Signed-off-by: Damien Le Moal Link: https://lore.kernel.org/r/20230912230551.454357-4-dlemoal@kernel.org Reviewed-by: John Garry Reviewed-by: Johannes Thumshirn Signed-off-by: Martin K. Petersen

scsi: libsas: Declare sas_set_phy_speed() static

2023-09-14T01:06:44Z

sas_set_phy_speed() is used only within sas_init.c. Declare this function as static. Signed-off-by: Damien Le Moal Link: https://lore.kernel.org/r/20230912230551.454357-3-dlemoal@kernel.org Reviewed-by: John Garry Reviewed-by: Johannes Thumshirn Signed-off-by: Martin K. Petersen

scsi: libsas: Move local functions declarations to sas_internal.h

2023-09-14T01:06:44Z

Move the declarations of functions used only within libsas from include/scsi/libsas.h to drivers/scsi/libsas/sas_internal.h Signed-off-by: Damien Le Moal Link: https://lore.kernel.org/r/20230912230551.454357-2-dlemoal@kernel.org Reviewed-by: John Garry Reviewed-by: Johannes Thumshirn Signed-off-by: Martin K. Petersen

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

2023-09-09T19:01:33Z

Pull more SCSI updates from James Bottomley: "Mostly small stragglers that missed the initial merge. Driver updates are qla2xxx and smartpqi (mp3sas has a high diffstat due to the volatile qualifier removal, fnic due to unused function removal and sd.c has a lot of code shuffling to remove forward declarations)" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits) scsi: ufs: core: No need to update UPIU.header.flags and lun in advanced RPMB handler scsi: ufs: core: Add advanced RPMB support where UFSHCI 4.0 does not support EHS length in UTRD scsi: mpt3sas: Remove volatile qualifier scsi: mpt3sas: Perform additional retries if doorbell read returns 0 scsi: libsas: Simplify sas_queue_reset() and remove unused code scsi: ufs: Fix the build for the old ARM OABI scsi: qla2xxx: Fix unused variable warning in qla2xxx_process_purls_pkt() scsi: fnic: Remove unused functions fnic_scsi_host_start/end_tag() scsi: qla2xxx: Fix spelling mistake "tranport" -> "transport" scsi: fnic: Replace sgreset tag with max_tag_id scsi: qla2xxx: Remove unused variables in qla24xx_build_scsi_type_6_iocbs() scsi: qla2xxx: Fix nvme_fc_rcv_ls_req() undefined error scsi: smartpqi: Change driver version to 2.1.24-046 scsi: smartpqi: Enhance error messages scsi: smartpqi: Enhance controller offline notification scsi: smartpqi: Enhance shutdown notification scsi: smartpqi: Simplify lun_number assignment scsi: smartpqi: Rename pciinfo to pci_info scsi: smartpqi: Rename MACRO to clarify purpose scsi: smartpqi: Add abort handler ...