kernel/drivers/pinctrl/meson, branch linux-5.1.y

Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2019-03-11T18:12:50Z

Pull pin control updates from Linus Walleij: "This is a calm cycle, not much happened this time around: not even much incremental development. Some three new drivers, that is all. No core changes. New drivers: - NXP (ex Freescale) i.MX 8QM driver. - NXP (ex Freescale) i.MX 8MM driver. - AT91 SAM9X60 subdriver. Improvements: - Support for external interrups (EINT) on Mediatek virtual GPIOs. - Make BCM2835 pin config fully generic. - Lots of Renesas SH-PFC incremental improvements" * tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits) pinctrl: imx: fix scu link errors dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding pinctrl: qcom: spmi-gpio: Reorder debug print pinctrl: nomadik: fix possible object reference leak pinctrl: stm32: return error upon hwspinlock failure pinctrl: stm32: fix memory leak issue pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions pinctrl: sh-pfc: Validate fixed-size field widths at build time pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group pinctrl: sh-pfc: emev2: Add missing pinmux functions pinctrl: sunxi: Support I/O bias voltage setting on A80 pinctrl: ingenic: Add LCD pins for the JZ4725B SoC pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl pinctrl: bcm2835: declare pin config as generic pinctrl: qcom: qcs404: Drop unused UFS_RESET macro dt-bindings: add documentation for slew rate ...

pinctrl: meson: meson8b: fix the sdxc_a data 1..3 pins

2019-02-17T21:24:32Z

Fix the mismatch between the "sdxc_d13_1_a" pin group definition from meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a"). This makes it possible to use "sdxc_d13_1_a" in device-tree files to route the MMC data 1..3 pins to GPIOX_1..3. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl Signed-off-by: Linus Walleij

Merge branch 'ib-meson-fixes' into devel

2019-01-22T09:55:07Z

pinctrl: meson: add optional region for drive strength

2019-01-21T13:50:20Z

On the G12a, there is a new 'region' to handle the drive-strength. This is optional since the older do not have this. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Jerome Brunet Signed-off-by: Linus Walleij

pinctrl: meson: fix G12A ao pull registers base address

2019-01-21T13:49:57Z

Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG and AO_GPIO_O. These bits of controlling output level are remapped to the new register AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable. These bits of controlling pull enable are remapped to the new register AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling pull type(up/down). The new layout of ao gpio/pull registers is as follows: - AO_GPIO_O_EN_N [offset: 0x9 << 2] - AO_GPIO_I [offset: 0xa << 2] - AO_RTI_PULL_UP_REG [offset: 0xb << 2] - AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2] - AO_GPIO_O [offset: 0xd << 2] From above, we can see ao GPIO registers region has been separated by the ao pull registers. In order to ensure the continuity of the region on software, the ao GPIO and ao pull registers use the same base address, but can be identified by the offset. Fixes: 29ae0952e85f ("pinctrl: meson-g12a: add pinctrl driver support") Signed-off-by: Xingyu Chen Signed-off-by: Jianxin Pan Signed-off-by: Jerome Brunet Signed-off-by: Linus Walleij

pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pins

2019-01-14T08:30:14Z

Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines. Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to rely on the bootloader to set them up correctly. The vendor u-boot sources for Odroid-C1 use the following Ethernet pinmux configuration: SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f); SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000); This translates to the following pin groups in the mainline kernel: - register 6 bit 0: eth_rxd1 (DIF_0_P) - register 6 bit 1: eth_rxd0 (DIF_0_N) - register 6 bit 2: eth_rx_dv (DIF_1_P) - register 6 bit 3: eth_rx_clk (DIF_1_N) - register 6 bit 6: eth_tx_en (DIF_3_P) - register 6 bit 8: eth_ref_clk (DIF_3_N) - register 6 bit 9: eth_mdc (DIF_4_P) - register 6 bit 10: eth_mdio_en (DIF_4_N) - register 6 bit 11: eth_tx_clk (GPIOH_9) - register 6 bit 12: eth_txd2 (GPIOH_8) - register 6 bit 13: eth_txd3 (GPIOH_7) - register 7 bit 20: eth_txd0_0 (GPIOH_6) - register 7 bit 21: eth_txd1_0 (GPIOH_5) - register 7 bit 22: eth_rxd3 (DIF_2_P) - register 7 bit 23: eth_rxd2 (DIF_2_N) All functions except eth_rxd2 and eth_rxd3 are already supported by the pinctrl-meson8b driver. Suggested-by: Jianxin Pan Signed-off-by: Martin Blumenstingl Reviewed-by: Kevin Hilman Tested-by: Emiliano Ingrassia Reviewed-by: Emiliano Ingrassia Signed-off-by: Linus Walleij

Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

2019-01-01T21:19:16Z

Pull pin control updates from Linus Walleij: "We have no core changes but lots of incremental development in drivers all over the place: Renesas, NXP, Mediatek and Actions Semiconductor keep churning out new SoCs. I have some subtree maintainers for Renesas and Intel helping out to keep down the load, it's been working smoothly (Samsung also have a subtree but it was not used this cycle.) New drivers: - NXP (ex Freescale) i.MX 8 QXP SoC driver. - Mediatek MT6797 SoC driver. - Mediatek MT7629 SoC driver. - Actions Semiconductor S700 SoC driver. - Renesas RZ/A2 SoC driver. - Allwinner sunxi suniv F1C100 SoC driver. - Qualcomm PMS405 PMIC driver. - Microsemi Ocelot Jaguar2 SoC driver. Improvements: - Some RT improvements (using raw spinlocks where appropriate). - A lot of new pin sets on the Renesas PFC pin controllers. - GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO chips, and Xway. - Major modernization of the Intel pin control drivers. - STM32 pin control driver will now synchronize usage of pins with another CPU using a hardware spinlock" * tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits) dt-bindings: arm: fsl-scu: add imx8qm pinctrl support pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ pinctrl: imx-scu: Depend on IMX_SCU pinctrl: ocelot: Add dependency on HAS_IOMEM pinctrl: ocelot: add MSCC Jaguar2 support pinctrl: bcm: ns: support updated DT binding as syscon subnode dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon MAINTAINERS: merge at91 pinctrl entries pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP pinctrl: uniphier: constify uniphier_pinctrl_socdata pinctrl: mediatek: improve Kconfig dependencies pinctrl: msm: mark PM functions as __maybe_unused dt-bindings: pinctrl: sunxi: Add supply properties pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length ...

pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD

2018-12-21T10:00:54Z

Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b") Signed-off-by: Martin Blumenstingl Signed-off-by: Linus Walleij

pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD

2018-12-21T10:00:31Z

Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be configured in devicetree using groups = BOOTx or groups = CARDx. This makes the behavior consistent with other pins inside the same driver as well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers. Fixes: 6ac730951104a4 ("pinctrl: add driver for Amlogic Meson SoCs") Signed-off-by: Martin Blumenstingl Signed-off-by: Linus Walleij

pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"

2018-12-21T09:59:58Z

Rename the existing "gpio" function to "gpio_periphs". This makes it consistent with the "gpio_aobus" function. Also GXBB and GXL are also using the "gpio_periphs" naming, so this makes the code here consistent with other Amlogic pinctrl drivers. No functional changes since thee "gpio" function is currently not used. Signed-off-by: Martin Blumenstingl Signed-off-by: Linus Walleij