kernel/drivers/phy/tegra/xusb-tegra186.c, branch linux-6.9.y

phy: tegra: xusb: Support sleepwalk for Tegra234

2023-03-20T12:44:59Z

Add new registers programming in sleepwalk sequence for Tegra234: MASTER_ENABLE_A/B/C/D in XUSB_AO_UTMIP_SLEEPWALK. Signed-off-by: Henry Lin Signed-off-by: Haotien Hsu Link: https://lore.kernel.org/r/20230309061708.4156383-1-haotienh@nvidia.com Signed-off-by: Vinod Koul

phy: tegra: xusb: Add Tegra234 support

2023-01-17T16:27:42Z

Add support for the XUSB pad controller found on Tegra234 SoCs. It is mostly similar to the same IP found on Tegra194, because most of the Tegra234 XUSB PADCTL registers definition and programming sequence are the same as Tegra194, Tegra234 XUSB PADCTL can share the same driver with Tegra186 and Tegra194 XUSB PADCTL. Introduce a new feature, USB2 HW tracking, for Tegra234. The feature is to enable HW periodical PAD tracking which measure and capture the electric parameters of USB2.0 PAD. Signed-off-by: Sing-Han Chen Co-developed-by: Wayne Chang Signed-off-by: Wayne Chang Signed-off-by: Jon Hunter Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman

phy: tegra: xusb: Disable trk clk when not in use

2023-01-17T16:27:41Z

Pad tracking is a one-time calibration for Tegra186 and Tegra194. Clk should be disabled after calibration. Disable clk after calibration. While at it add 100us delay for HW recording the calibration value. Signed-off-by: Wayne Chang Signed-off-by: Jon Hunter Link: https://lore.kernel.org/r/20230111110450.24617-5-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman

phy: tegra: xusb: Remove usb3 supply

2022-11-07T04:50:25Z

Remove redundant codes for getting the vbus supply of usb3 ports because we get and control the vbus supply by the companion usb2 ports Signed-off-by: Wayne Chang Signed-off-by: Haotien Hsu Reviewed-by: Jon Hunter Link: https://lore.kernel.org/r/20221005084031.2154251-1-haotienh@nvidia.com Signed-off-by: Vinod Koul

Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2022-10-07T23:48:26Z

Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1. Nothing major in here, lots of little things with new devices supported and updates for a few drivers. Highlights include: - thunderbolt/USB4 devices supported a bit better than before, and some new ids to enable new hardware devices - USB gadget uvc updates for newer video formats and better v4l integration (the v4l portions were acked by those maintainers) - typec updates for tiny issues and more typec drivers for new chips. - xhci tiny updates for minor issues - big usb-serial ftdi_sio driver update to handle new devices better - lots of tiny dwc3 fixes and updates for the IP block that is showing up everywhere these days - dts updates for new devices being supported - other tiny janitorial and cleanups fixes for lots of different USB drivers. Full details are in the shortlog. All of these have been in linux-next for a while with no reported issues" * tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits) usb: gadget: uvc: don't put item still in use usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video() usb: host: ehci-exynos: switch to using gpiod API Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present" Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"" dt-bindings: usb: Convert FOTG210 to dt schema usb: mtu3: fix failed runtime suspend in host only mode USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl" usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra usb: typec: Replace custom implementation of device_match_fwnode() usb: typec: ucsi: Don't warn on probe deferral usb: add quirks for Lenovo OneLink+ Dock MAINTAINERS: switch dwc3 to Thinh usb: idmouse: fix an uninit-value in idmouse_open USB: PHY: JZ4770: Switch to use dev_err_probe() helper usb: phy: generic: Switch to use dev_err_probe() helper usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs usb: cdns3: remove dead code usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair usb: musb: sunxi: Switch to use dev_err_probe() helper ...

phy: tegra: xusb: Use dev_err_probe() to simplify code

2022-09-24T07:04:56Z

In the probe path, dev_err() can be replaced with dev_err_probe() which will check if error code is -EPROBE_DEFER and prints the error name. It also sets the defer probe reason which can be checked later through debugfs. Signed-off-by: Yuan Can Link: https://lore.kernel.org/r/20220922092243.22281-1-yuancan@huawei.com Signed-off-by: Vinod Koul

phy: tegra: xusb: add utmi pad power on/down ops

2022-08-19T09:10:08Z

Add utmi_pad_power_on/down ops for each SOC instead of exporting tegra_phy_xusb_utmi_pad_power_on/down directly for Tegra186 chip. Signed-off-by: BH Hsieh Signed-off-by: Jim Lin Link: https://lore.kernel.org/r/20220816082353.13390-2-jilin@nvidia.com Signed-off-by: Greg Kroah-Hartman

phy: tegra: xusb: Add wake/sleepwalk for Tegra186

2021-06-03T12:52:45Z

This commit implements Tegra186/Tegra194 XUSB PADCTL/AO wake and sleepwalk operations. Signed-off-by: JC Kuo Acked-By: Vinod Koul Signed-off-by: Thierry Reding

phy: tegra: Don't use device-managed API to allocate ports

2020-03-19T13:00:05Z

The device-managed allocation API doesn't work well with the life-cycle of device objects. Since ports have device objects allocated within, it can lead to situations where these devices need to stay around until after their parent pad controller has been unbound from its driver. The device-managed memory allocated for the port objects will, however, get freed when the pad controller unbinds from the driver. This can cause use-after-free errors down the road. Note that the device is deleted as part of the driver unbind operation, so there isn't much that can be done with it after that point, but the memory still needs to stay around to ensure none of the references are invalidated. One situation where this arises is when a VBUS supply is associated with a USB 2 or 3 port. When that supply is released using regulator_put() an SRCU call will queue the release of the device link connecting the port and the regulator after a grace period. This means that the regulator is going to keep on to the last reference of the port device even after the pad controller driver was unbound (which is when the memory backing the port device is freed). Fix this by allocating port objects using non-device-managed memory. Add release callbacks for these objects so that their memory gets freed when the last reference goes away. This decouples the port devices' lifetime from the "active" lifetime of the pad controller (i.e. the time during which the pad controller driver owns the device). Signed-off-by: Thierry Reding

phy: tegra: Fix regulator leak

2020-03-19T13:00:04Z

Devices are created for each port of the XUSB pad controller. Each USB 2 and USB 3 port can potentially have an associated VBUS power supply that needs to be removed when the device is removed. Since port devices never bind to a driver, the driver core will not get to perform the cleanup of device-managed resources that usually happens on driver unbind. Now, the driver core will also perform device-managed resource cleanup for driver-less devices when they are released. However, when a device link is created between the regulator and the port device, as part of regulator_get(), the regulator takes a reference to the port device and prevents it from being released unless regulator_put() is called, which will never happen. Avoid this by using the non-device-managed API and manually releasing the regulator reference when the port is unregistered. Signed-off-by: Thierry Reding