kernel/drivers/phy/rockchip, branch linux-6.9.y

phy: phy-rockchip-samsung-hdptx: Select CONFIG_RATIONAL

2024-04-12T09:42:13Z

Ensure CONFIG_RATIONAL is selected in order to fix the following link error with some kernel configurations: drivers/phy/rockchip/phy-rockchip-samsung-hdptx.o: in function `rk_hdptx_ropll_tmds_cmn_config': phy-rockchip-samsung-hdptx.c:(.text+0x950): undefined reference to `rational_best_approximation' Fixes: 553be2830c5f ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver") Reported-by: kernel test robot Closes: https://lore.kernel.org/oe-kbuild-all/202404090540.2l1TEkDF-lkp@intel.com/ Signed-off-by: Cristian Ciocaltea Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20240408222926.32708-1-cristian.ciocaltea@collabora.com Signed-off-by: Vinod Koul

phy: rockchip: naneng-combphy: Fix mux on rk3588

2024-04-06T09:01:13Z

The pcie1l0_sel and pcie1l1_sel bits in PCIESEL_CON configure the mux for PCIe1L0 and PCIe1L1 to either the PIPE Combo PHYs or the PCIe3 PHY. Thus this configuration interfers with the data-lanes configuration done by the PCIe3 PHY. RK3588 has three Combo PHYs. The first one has a dedicated PCIe controller and is not affected by this. For the other two Combo PHYs, there is one mux for each of them. pcie1l0_sel selects if PCIe 1L0 is muxed to Combo PHY 1 when bit is set to 0 or to the PCIe3 PHY when bit is set to 1. pcie1l1_sel selects if PCIe 1L1 is muxed to Combo PHY 2 when bit is set to 0 or to the PCIe3 PHY when bit is set to 1. Currently the code always muxes 1L0 and 1L1 to the Combi PHYs once one of them is being used in PCIe mode. This is obviously wrong when at least one of the ports should be muxed to the PCIe3 PHY. Fix this by introducing Combo PHY identification and then only setting up the required bit. Fixes: a03c44277253 ("phy: rockchip: Add naneng combo phy support for RK3588") Reported-by: Michal Tomek Signed-off-by: Sebastian Reichel Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-3-9907136eeafd@kernel.org Signed-off-by: Vinod Koul

phy: rockchip-snps-pcie3: fix clearing PHP_GRF_PCIESEL_CON bits

2024-04-06T09:01:13Z

Currently the PCIe v3 PHY driver only sets the pcie1ln_sel bits, but does not clear them because of an incorrect write mask. This fixes up the issue by using a newly introduced constant for the write mask. While at it also introduces a proper GENMASK based constant for the PCIE30_PHY_MODE. Fixes: 2e9bffc4f713 ("phy: rockchip: Support PCIe v3") Signed-off-by: Sebastian Reichel Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-2-9907136eeafd@kernel.org Signed-off-by: Vinod Koul

phy: rockchip-snps-pcie3: fix bifurcation on rk3588

2024-04-06T09:01:13Z

So far all RK3588 boards use fully aggregated PCIe. CM3588 is one of the few boards using this feature and apparently it is broken. The PHY offers the following mapping options: port 0 lane 0 - always mapped to controller 0 (4L) port 0 lane 1 - to controller 0 or 2 (1L0) port 1 lane 0 - to controller 0 or 1 (2L) port 1 lane 1 - to controller 0, 1 or 3 (1L1) The data-lanes DT property maps these as follows: 0 = no controller (unsupported by the HW) 1 = 4L 2 = 2L 3 = 1L0 4 = 1L1 That allows the following configurations with first column being the mainline data-lane mapping, second column being the downstream name, third column being PCIE3PHY_GRF_CMN_CON0 and PHP_GRF_PCIESEL register values and final column being the user visible lane setup: <1 1 1 1> = AGGREG = [4 0] = x4 (aggregation) <1 1 2 2> = NANBNB = [0 0] = x2 x2 (no bif.) <1 3 2 2> = NANBBI = [1 1] = x2 x1x1 (bif. of port 0) <1 1 2 4> = NABINB = [2 2] = x1x1 x2 (bif. of port 1) <1 3 2 4> = NABIBI = [3 3] = x1x1 x1x1 (bif. of both ports) The driver currently does not program PHP_GRF_PCIESEL correctly, which is fixed by this patch. As a side-effect the new logic is much simpler than the old logic. Fixes: 2e9bffc4f713 ("phy: rockchip: Support PCIe v3") Signed-off-by: Michal Tomek Signed-off-by: Sebastian Reichel Acked-by: Heiko Stuebner Link: https://lore.kernel.org/r/20240404-rk3588-pcie-bifurcation-fixes-v1-1-9907136eeafd@kernel.org Signed-off-by: Vinod Koul

phy: constify of_phandle_args in xlate

2024-02-23T12:13:14Z

The xlate callbacks are supposed to translate of_phandle_args to proper provider without modifying the of_phandle_args. Make the argument pointer to const for code safety and readability. Signed-off-by: Krzysztof Kozlowski Acked-by: Thierry Reding Acked-by: Linus Walleij Acked-by: Florian Fainelli #Broadcom Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul

phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver

2024-02-16T06:56:56Z

Add driver for the HDMI/eDP TX Combo PHY found on Rockchip RK3588 SoC. The PHY is based on a Samsung IP block and supports HDMI 2.1 TMDS, FRL and eDP links. The maximum data rate is 12Gbps (FRL), while the minimum is 250Mbps (TMDS). Only the TMDS link is currently supported. Co-developed-by: Algea Cao Signed-off-by: Algea Cao Tested-by: Heiko Stuebner Signed-off-by: Cristian Ciocaltea Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-2-e7974f46c1a7@collabora.com Signed-off-by: Vinod Koul

phy: phy-rockchip-inno-usb2: Add RK3128 support

2023-11-27T13:06:29Z

Add registers to support the 2-port usb2 phy found in RK312x SoC familiy. Signed-off-by: Alex Bee Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20231119121340.109025-3-knaerzche@gmail.com Signed-off-by: Vinod Koul

phy: rockchip-inno-usb2: Split ID interrupt phy registers

2023-11-27T13:06:29Z

Commit 51a9b2c03dd3 ("phy: rockchip-inno-usb2: Handle ID IRQ") added ID detection interrupt registers. However the current implementation assumes that falling and rising edge interrupt are always enabled in registers spanning over subsequent bits. That is not the case for RK3128's version of the phy and this implementation can't be used as-is, since there are bits with different purpose in between. This splits up the register definitions for id_det_en, id_det_en and id_det_clr registers in rising and falling edge variants. It's required as preparation to support RK3128's Innosilicon usb2 phy as well in this driver and matches pretty much to what the vendor does, so I'm not expecting issues for other SoCs with that change. Signed-off-by: Alex Bee Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20231119121340.109025-2-knaerzche@gmail.com Signed-off-by: Vinod Koul

phy: rockchip-inno-usb2: Drop unnecessary DT includes

2023-10-13T10:16:09Z

Neither of_address.h or of_platform.h are used in the driver, so drop them. Signed-off-by: Rob Herring Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20231009172923.2457844-17-robh@kernel.org Signed-off-by: Vinod Koul

phy: Use device_get_match_data()

2023-10-13T10:15:40Z

Use preferred device_get_match_data() instead of of_match_device() to get the driver match data. With this, adjust the includes to explicitly include the correct headers. Signed-off-by: Rob Herring Reviewed-by: Heiko Stuebner Link: https://lore.kernel.org/r/20231009172923.2457844-15-robh@kernel.org Signed-off-by: Vinod Koul