kernel/drivers/pci/controller/dwc/pcie-qcom.c, branch linux-6.9.y

Merge tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

2024-03-14T17:58:27Z

Pull PCI updates from Bjorn Helgaas: "Enumeration: - Consolidate interrupt related code in irq.c (Ilpo Järvinen) - Reduce kernel size by replacing sysfs resource macros with functions (Ilpo Järvinen) - Reduce kernel size by compiling sysfs support only when CONFIG_SYSFS=y (Lukas Wunner) - Avoid using Extended Tags on 3ware-9650SE Root Port to work around an apparent hardware defect (Jörg Wedekind) Resource management: - Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner) - Move pci_iomap.c and other PCI-specific devres code to drivers/pci (Philipp Stanner) - Consolidate PCI devres code in devres.c (Philipp Stanner) Power management: - Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't know how to return correctly to D0, and remove previous quirk that wasn't as specific (Daniel Drake) - Allow runtime PM when the driver enables it but doesn't need any runtime PM callbacks (Raag Jadav) - Drain runtime-idle callbacks before driver removal to avoid races between .remove() and .runtime_idle(), which caused intermittent page faults when the rtsx .runtime_idle() accessed registers that its .remove() had already unmapped (Rafael J. Wysocki) Virtualization: - Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs with VFIO, e.g., for professional audio software on many Apple machines, at the cost of leaking state between VMs (Edmund Raile) Error handling: - Print all logged TLP Prefixes, not just the first, after AER or DPC errors (Ilpo Järvinen) - Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which still don't advertise a legal size (Paul Menzel) - Ignore expected DPC Surprise Down errors on hot removal (Smita Koralahalli) - Block runtime suspend while handling AER errors to avoid races that prevent the device form being resumed from D3hot (Stanislaw Gruszka) Peer-to-peer DMA: - Use atomic XA allocation in RCU read section (Christophe JAILLET) ASPM: - Collect bits of ASPM-related code that we need even without CONFIG_PCIEASPM into aspm.c (David E. Box) - Save/restore L1 PM Substates config for suspend/resume (David E. Box) - Update save_save when ASPM config is changed, so a .slot_reset() during error recovery restores the changed config, not the .probe()-time config (Vidya Sagar) Endpoint framework: - Refactor and improve pci_epf_alloc_space() API (Niklas Cassel) - Clean up endpoint BAR descriptions (Niklas Cassel) - Fix ntb_register_device() name leak in error path (Yang Yingliang) - Return actual error code for pci_vntb_probe() failure (Yang Yingliang) Broadcom STB PCIe controller driver: - Fix MDIO write polling, which previously never waited for completion (Jonathan Bell) Cadence PCIe endpoint driver: - Clear the ARI "Next Function Number" of last function (Jasko-EXT Wojciech) Freescale i.MX6 PCIe controller driver: - Simplify by replacing switch statements with function pointers for different hardware variants (Frank Li) - Simplify by using clk_bulk*() API (Frank Li) - Remove redundant DT clock and reg/reg-name details (Frank Li) - Add i.MX95 DT and driver support for both Root Complex and Endpoint mode (Frank Li) Microsoft Hyper-V host bridge driver: - Reduce memory usage by limiting ring buffer size to 16KB instead of 4 pages (Michael Kelley) Qualcomm PCIe controller driver: - Add X1E80100 DT and driver support (Abel Vesa) - Add DT 'required-opps' for SoCs that require a minimum performance level (Johan Hovold) - Make DT 'msi-map-mask' optional, depending on how MSI interrupts are mapped (Johan Hovold) - Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY configuration isn't tuned correctly for L0s (Johan Hovold) - Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski) - Enable BDF to SID translation by disabling bypass mode (Manivannan Sadhasivam) - Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay Sarkar) Synopsys DesignWare PCIe controller driver: - Allocate 64-bit MSI address if no 32-bit address is available (Ajay Agarwal) - Fix endpoint Resizable BAR to actually advertise the required 1MB size (Niklas Cassel) MicroSemi Switchtec management driver: - Release resources if the .probe() fails (Christophe JAILLET) Miscellaneous: - Make pcie_port_bus_type const (Ricardo B. Marliere)" * tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits) PCI/ASPM: Update save_state when configuration changes PCI/ASPM: Disable L1 before configuring L1 Substates PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state() PCI/ASPM: Save L1 PM Substates Capability for suspend/resume PCI: hv: Fix ring buffer size calculation PCI: dwc: endpoint: Fix advertised resizable BAR size PCI: cadence: Clear the ARI Capability Next Function Number of the last function PCI: dwc: Strengthen the MSI address allocation logic PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling PCI: qcom: Add X1E80100 PCIe support dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller PCI: qcom: Enable BDF to SID translation properly PCI/AER: Generalize TLP Header Log reading PCI/AER: Use explicit register size for PCI_ERR_CAP PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p dt-bindings: PCI: qcom: Do not require 'msi-map-mask' dt-bindings: PCI: qcom: Allow 'required-opps' PCI/AER: Block runtime suspend when handling errors PCI/ASPM: Move pci_save_ltr_state() to aspm.c PCI/ASPM: Always build aspm.c ...

PCI: qcom: Add X1E80100 PCIe support

2024-03-10T17:55:07Z

Add the compatible and the driver data for X1E80100 PCIe controller. There are 5 controller instances found on this platform, out of which 2 are Gen3 with speeds of up to 8.0GT/s, while the other 3 are Gen4 with speeds of up to 16GT/s. The version of the controller is 1.38.0 for all instances, but they are compatible with 1.9.0 config. The max link width is x8 for one controller, x4 for two of others and x2 for the two left. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20240301-x1e80100-pci-v4-2-7ab7e281d647@linaro.org Reviewed-by: Manivannan Sadhasivam Signed-off-by: Abel Vesa Signed-off-by: Krzysztof Wilczyński

PCI: qcom: Enable BDF to SID translation properly

2024-03-10T17:54:02Z

Qcom SoCs making use of ARM SMMU require BDF to SID translation table in the driver to properly map the SID for the PCIe devices based on their BDF identifier. This is currently achieved with the help of qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config. But With newer Qcom SoCs starting from SM8450, BDF to SID translation is set to bypass mode by default in hardware. Due to this, the translation table that is set in the qcom_pcie_config_sid_1_9_0() is essentially unused and the default SID is used for all endpoints in SoCs starting from SM8450. This is a security concern and also warrants swapping the DeviceID in DT while using the GIC ITS to handle MSIs from endpoints. The swapping is currently done like below in DT when using GIC ITS: /* * MSIs for BDF (1:0.0) only works with Device ID 0x5980. * Hence, the IDs are swapped. */ msi-map = <0x0 &gic_its 0x5981 0x1>, <0x100 &gic_its 0x5980 0x1>; Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0) gets the DeviceID 0x5980 which is associated with the default SID as per the iommu mapping in DT. So MSIs were delivered with IDs swapped so far. But this also means the Root Port (0:0.0) won't receive any MSIs (for PME, AER etc...) So let's fix these issues by clearing the BDF to SID bypass mode for all SoCs making use of the 1_9_0 config. This allows the PCIe devices to use the correct SID, thus avoiding the DeviceID swapping hack in DT and also achieving the isolation between devices. Fixes: 4c9398822106 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250") Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org Signed-off-by: Manivannan Sadhasivam Signed-off-by: Krzysztof Wilczyński Cc: stable@vger.kernel.org # 5.11

PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p

2024-03-08T16:05:46Z

Commit 9f4f3dfad8cf ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops") started enabling ASPM unconditionally when the hardware claims to support it. This triggers Correctable Errors for some PCIe devices on machines like the Lenovo ThinkPad X13s when L0s is enabled, which could indicate an incomplete driver ASPM implementation or that the hardware does in fact not support L0s. This has now been confirmed by Qualcomm to be the case for sc8280xp and its derivate platforms (e.g. sa8540p and sa8295p). Specifically, the PHY configuration used on these platforms is not correctly tuned for L0s and there is currently no updated configuration available. Add a new flag to the driver configuration data and use it to disable ASPM L0s on sc8280xp, sa8540p and sa8295p for now. Note that only the 1.9.0 ops enable ASPM currently. Link: https://lore.kernel.org/r/20240306095651.4551-4-johan+linaro@kernel.org Fixes: 9f4f3dfad8cf ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops") Signed-off-by: Johan Hovold Signed-off-by: Lorenzo Pieralisi Reviewed-by: Manivannan Sadhasivam Cc: stable@vger.kernel.org # 6.7

PCI/ASPM: Fix deadlock when enabling ASPM

2024-01-31T15:03:51Z

A last minute revert in 6.7-final introduced a potential deadlock when enabling ASPM during probe of Qualcomm PCIe controllers as reported by lockdep: ============================================ WARNING: possible recursive locking detected 6.7.0 #40 Not tainted -------------------------------------------- kworker/u16:5/90 is trying to acquire lock: ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc but task is already holding lock: ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(pci_bus_sem); lock(pci_bus_sem); *** DEADLOCK *** Call trace: print_deadlock_bug+0x25c/0x348 __lock_acquire+0x10a4/0x2064 lock_acquire+0x1e8/0x318 down_read+0x60/0x184 pcie_aspm_pm_state_change+0x58/0xdc pci_set_full_power_state+0xa8/0x114 pci_set_power_state+0xc4/0x120 qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom] pci_walk_bus+0x64/0xbc qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom] The deadlock can easily be reproduced on machines like the Lenovo ThinkPad X13s by adding a delay to increase the race window during asynchronous probe where another thread can take a write lock. Add a new pci_set_power_state_locked() and associated helper functions that can be called with the PCI bus semaphore held to avoid taking the read lock twice. Link: https://lore.kernel.org/r/ZZu0qx2cmn7IwTyQ@hovoldconsulting.com Link: https://lore.kernel.org/r/20240130100243.11011-1-johan+linaro@kernel.org Fixes: f93e71aea6c6 ("Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"") Signed-off-by: Johan Hovold Signed-off-by: Bjorn Helgaas Cc: # 6.7

Merge tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

2024-01-18T00:23:17Z

Pull pci updates from Bjorn Helgaas: "Enumeration: - Reserve ECAM so we don't assign it to PCI BARs; this works around bugs where BIOS included ECAM in a PNP0A03 host bridge window, didn't reserve it via a PNP0C02 motherboard device, and didn't allocate space for SR-IOV VF BARs (Bjorn Helgaas) - Add MMCONFIG/ECAM debug logging (Bjorn Helgaas) - Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas) - Log device type (Root Port, Switch Port, etc) during enumeration (Bjorn Helgaas) - Log bridges before downstream devices so the dmesg order is more logical (Bjorn Helgaas) - Log resource names (BAR 0, VF BAR 0, bridge window, etc) consistently instead of a mix of names and "reg 0x10" (Puranjay Mohan, Bjorn Helgaas) - Fix 64GT/s effective data rate calculation to use 1b/1b encoding rather than the 8b/10b or 128b/130b used by lower rates (Ilpo Järvinen) - Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI lpfc (Ilpo Järvinen) - Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen) Resource management: - Restructure pci_dev_for_each_resource() to avoid computing the address of an out-of-bounds array element (the bounds check was performed later so the element was never actually *read*, but it's nicer to avoid even computing an out-of-bounds address) (Andy Shevchenko) Driver binding: - Convert pci-host-common.c platform .remove() callback to .remove_new() returning 'void' since it's not useful to return error codes here (Uwe Kleine-König) - Convert exynos, keystone, kirin from .remove() to .remove_new(), which returns void instead of int (Uwe Kleine-König) - Drop unused struct pci_driver.node member (Mathias Krause) Virtualization: - Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc) Error handling: - Log AER errors as "Correctable" (not "Corrected") or "Uncorrectable" to match spec terminology (Bjorn Helgaas) - Decode Requester ID when no error info found instead of printing the raw hex value (Bjorn Helgaas) Endpoint framework: - Use a unique test pattern for each BAR in the pci_endpoint_test to make it easier to debug address translation issues (Niklas Cassel) Broadcom STB PCIe controller driver: - Add DT property "brcm,clkreq-mode" and driver support for different CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan) Freescale Layerscape PCIe controller driver: - Add suspend/resume support for Layerscape LS1043a and LS1021a, including software-managed PME_Turn_Off and transitions between L0, L2/L3_Ready Link states (Frank Li) MediaTek PCIe controller driver: - Clear MSI interrupt status before handler to avoid missing MSIs that occur after the handler (qizhong cheng) MediaTek PCIe Gen3 controller driver: - Update mediatek-gen3 translation window setup to handle MMIO space that is not a power of two in size (Jianjun Wang) Qualcomm PCIe controller driver: - Increase qcom iommu-map maxItems to accommodate SDX55 (five entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski) - Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof Kozlowski) - Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof Kozlowski) - Correct the qcom "reset-name" property, previously incorrectly called "reset-names" (Krzysztof Kozlowski) - Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil Armstrong) Renesas R-Car PCIe controller driver: - Replace of_device.h with explicit of.h include to untangle header usage (Rob Herring) - Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators on KingFisher (Wolfram Sang) SiFive FU740 PCIe controller driver: - Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to ARCH_SIFIVE (Conor Dooley) Synopsys DesignWare PCIe controller driver: - Align iATU mapping for endpoint MSI-X (Niklas Cassel) - Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro Shimoda) - Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro Shimoda) - Rename struct dw_pcie_ep_ops.func_conf_select() to .get_dbi_offset() to be more descriptive (Yoshihiro Shimoda) - Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro Shimoda) TI J721E PCIe driver: - Add j721e DT and driver support for 'num-lanes' for devices that support x1, x2, or x4 Links (Matt Ranostay) - Add j721e DT compatible strings and driver support for j784s4 (Matt Ranostay) - Make TI J721E Kconfig depend on ARCH_K3 since the hardware is specific to those TI SoC parts (Peter Robinson) TI Keystone PCIe controller driver: - Hold power management references to all PHYs while enabling them to avoid a race when one provides clocks to others (Siddharth Vadapalli) Xilinx XDMA PCIe controller driver: - Remove redundant dev_err(), since platform_get_irq() and platform_get_irq_byname() already log errors (Yang Li) - Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq() (Krzysztof Wilczyński) - Fix xilinx_pl_dma_pcie_init_irq_domain() error return when irq_domain_add_linear() fails (Harshit Mogalapalli) MicroSemi Switchtec management driver: - Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm ioremapping in switchtec_pci_probe(). Previously the cleanup was done in stdev_release(), which used stale pointers if stdev->cdev happened to be open when the PCI device was removed (Daniel Stodden) Miscellaneous: - Convert interrupt terminology from "legacy" to "INTx" to be more specific and match spec terminology (Damien Le Moal) - In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of deprecated ida_simple_*() API with ida_alloc() and ida_free() (Christophe JAILLET)" * tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits) PCI: Fix kernel-doc issues PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode" PCI: mediatek-gen3: Fix translation window size calculation PCI: mediatek: Clear interrupt status before dispatching handler PCI: keystone: Fix race condition when initializing PHYs PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain() PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq() PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members misc: pci_endpoint_test: Use a unique test pattern for each BAR PCI: j721e: Make TI J721E depend on ARCH_K3 PCI: j721e: Add TI J784S4 PCIe configuration PCI/AER: Use explicit register sizes for struct members PCI/AER: Decode Requester ID when no error info found PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors ...

PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members

2024-01-06T07:51:08Z

Since the name of the dw_pcie_host_ops struct makes it obvious that it's for the PCIe Host, drop the host prefix from the struct members. [kwilczynski: commit log] Suggested-by: Serge Semin Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-2-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Yoshihiro Shimoda Signed-off-by: Krzysztof Wilczyński Reviewed-by: Manivannan Sadhasivam Reviewed-by: Serge Semin Reviewed-by: Thomas Petazzoni Acked-by: Heiko Stuebner Acked-by: Jesper Nilsson Acked-by: Kunihiko Hayashi Acked-by: Lei Chuanhua Acked-by: Nobuhiro Iwamatsu

PCI: qcom: Clean up ASPM comment

2023-12-11T18:08:53Z

Break up the newly added ASPM comment so that it fits within the soft 80 character limit and becomes more readable. Link: https://lore.kernel.org/r/20231128081512.19387-5-johan+linaro@kernel.org Signed-off-by: Johan Hovold Signed-off-by: Bjorn Helgaas

PCI: qcom: Fix potential deadlock when enabling ASPM

2023-12-11T18:08:43Z

The qcom_pcie_enable_aspm() helper is called from pci_walk_bus() during host init to enable ASPM. Since pci_walk_bus() already holds a pci_bus_sem read lock, use pci_enable_link_state_locked() to enable link states in order to avoid a potential deadlock (e.g. in case someone takes a write lock before reacquiring the read lock). This issue was reported by lockdep: ============================================ WARNING: possible recursive locking detected 6.7.0-rc1 #4 Not tainted -------------------------------------------- kworker/u16:6/147 is trying to acquire lock: ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_enable_link_state+0x74/0x1e8 but task is already holding lock: ffffbf3ff9d2cfa0 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(pci_bus_sem); lock(pci_bus_sem); *** DEADLOCK *** Fixes: 9f4f3dfad8cf ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops") Link: https://lore.kernel.org/r/20231128081512.19387-4-johan+linaro@kernel.org Signed-off-by: Johan Hovold [bhelgaas: add "potential" in subject since the deadlock has only been reported by lockdep, include helper name in commit log] Signed-off-by: Bjorn Helgaas Reviewed-by: Manivannan Sadhasivam

Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci

2023-11-03T00:05:18Z

Pull pci updates from Bjorn Helgaas: "Enumeration: - Use acpi_evaluate_dsm_typed() instead of open-coding _DSM evaluation to learn device characteristics (Andy Shevchenko) - Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK definition (Ilpo Järvinen) - Simplify config access error checking in various drivers (Ilpo Järvinen) - Use pcie_capability_clear_word() (not pcie_capability_clear_and_set_word()) when only clearing (Ilpo Järvinen) - Add pci_get_base_class() to simplify finding devices using base class only (ignoring subclass and programming interface) (Sui Jingfeng) - Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA devices from before the Class Code was added to PCI (Sui Jingfeng) - Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to include ancient VGA devices (Sui Jingfeng) Resource management: - Make pci_assign_unassigned_resources() non-init because sparc uses it after init (Randy Dunlap) Driver binding: - Retain .remove() and .probe() callbacks (previously __init) because sysfs may cause them to be called later (Uwe Kleine-König) - Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so it can be claimed by dwc3 instead (Vicki Pfau) PCI device hotplug: - Add Ampere Altra Attention Indicator extension driver for acpiphp (D Scott Phillips) Power management: - Quirk VideoPropulsion Torrent QN16e with longer delay after reset (Lukas Wunner) - Prevent users from overriding drivers that say we shouldn't use D3cold (Lukas Wunner) - Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4 because wakeup interrupts from those states don't work if amd-pmc has put the platform in a hardware sleep state (Mario Limonciello) IOMMU: - Disable ATS for Intel IPU E2000 devices with invalidation message endianness erratum (Bartosz Pawlowski) Error handling: - Factor out interrupt enable/disable into helpers (Kai-Heng Feng) Peer-to-peer DMA: - Fix flexible-array usage in struct pci_p2pdma_pagemap in case we ever use pagemaps with multiple entries (Gustavo A. R. Silva) ASPM: - Revert a change that broke when drivers disabled L1 and users later enabled an L1.x substate via sysfs, and fix a similar issue when users disabled L1 via sysfs (Heiner Kallweit) Endpoint framework: - Fix double free in __pci_epc_create() (Dan Carpenter) - Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie) Cadence PCIe controller driver: - Drop unused "is_rc" member (Li Chen) Freescale Layerscape PCIe controller driver: - Enable 64-bit addressing in endpoint mode (Guanhua Gao) Intel VMD host bridge driver: - Fix multi-function header check (Ilpo Järvinen) Microsoft Hyper-V host bridge driver: - Annotate struct hv_dr_state with __counted_by (Kees Cook) NVIDIA Tegra194 PCIe controller driver: - Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup() already does this via dw_pcie_link_set_max_link_width() (Yoshihiro Shimoda) Qualcomm PCIe controller driver: - Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed (Manivannan Sadhasivam) - Add a .write_dbi2() callback so DBI2 register writes, e.g., for setting the BAR size, work correctly (Manivannan Sadhasivam) - Enable ASPM for platforms that use 1.9.0 ops, because the PCI core doesn't enable ASPM states that haven't been enabled by the firmware (Manivannan Sadhasivam) Renesas R-Car Gen4 PCIe controller driver: - Add DesignWare core support (set max link width, EDMA_UNROLL flag, .pre_init(), .deinit(), etc) for use by R-Car Gen4 driver (Yoshihiro Shimoda) - Add driver and DT schema for DesignWare-based Renesas R-Car Gen4 controller in both host and endpoint mode (Yoshihiro Shimoda) Xilinx NWL PCIe controller driver: - Update ECAM size to support 256 buses (Thippeswamy Havalige) - Stop setting bridge primary/secondary/subordinate bus numbers, since PCI core does this (Thippeswamy Havalige) Xilinx XDMA controller driver: - Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with Xilinx XDMA Soft IP (Thippeswamy Havalige) Miscellaneous: - Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT macros (Ilpo Järvinen, Bjorn Helgaas) - Remove logic_outb(), _outw(), outl() duplicate declarations (John Sanpe) - Replace unnecessary UTF-8 in Kconfig help text because menuconfig doesn't render it correctly (Liu Song)" * tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits) PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word() PCI: endpoint: Fix double free in __pci_epc_create() PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge PCI: xilinx-cpm: Move IRQ definitions to a common header PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields PCI: hotplug: Add Ampere Altra Attention Indicator extension driver PCI/AER: Factor out interrupt toggling into helpers PCI: acpiphp: Allow built-in drivers for Attention Indicators PCI/portdrv: Use FIELD_GET() PCI/VC: Use FIELD_GET() PCI/PTM: Use FIELD_GET() PCI/PME: Use FIELD_GET() PCI/ATS: Use FIELD_GET() PCI/ATS: Show PASID Capability register width in bitmasks PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common() ...