kernel/drivers/net, branch linux-6.1.y

net: ethernet: ec_bhf: Fix dma_free_coherent() dma handle

2026-03-04T12:20:56Z

[ Upstream commit ffe68c3766997d82e9ccaf1cdbd47eba269c4aa2 ] dma_free_coherent() in error path takes priv->rx_buf.alloc_len as the dma handle. This would lead to improper unmapping of the buffer. Change the dma handle to priv->rx_buf.alloc_phys. Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.") Cc: Signed-off-by: Thomas Fourier Link: https://patch.msgid.link/20260213164340.77272-2-fourier.thomas@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: intel: fix PCI device ID conflict between i40e and ipw2200

2026-03-04T12:20:54Z

[ Upstream commit d03e094473ecdeb68d853752ba467abe13e1de44 ] The ID 8086:104f is matched by both i40e and ipw2200. The same device ID should not be in more than one driver, because in that case, which driver is used is unpredictable. Fix this by taking advantage of the fact that i40e devices use PCI_CLASS_NETWORK_ETHERNET and ipw2200 devices use PCI_CLASS_NETWORK_OTHER to differentiate the devices. Fixes: 2e45d3f4677a ("i40e: Add support for X710 B/P & SFP+ cards") Cc: stable@vger.kernel.org Acked-by: Johannes Berg Signed-off-by: Ethan Nelson-Moore Reviewed-by: Aleksandr Loktionov Link: https://patch.msgid.link/20260210021235.16315-1-enelsonmoore@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: macb: Fix tx/rx malfunction after phy link down and up

2026-03-04T12:20:54Z

[ Upstream commit bf9cf80cab81e39701861a42877a28295ade266f ] In commit 99537d5c476c ("net: macb: Relocate mog_init_rings() callback from macb_mac_link_up() to macb_open()"), the mog_init_rings() callback was moved from macb_mac_link_up() to macb_open() to resolve a deadlock issue. However, this change introduced a tx/rx malfunction following phy link down and up events. The issue arises from a mismatch between the software queue->tx_head, queue->tx_tail, queue->rx_prepared_head, and queue->rx_tail values and the hardware's internal tx/rx queue pointers. According to the Zynq UltraScale TRM [1], when tx/rx is disabled, the internal tx queue pointer resets to the value in the tx queue base address register, while the internal rx queue pointer remains unchanged. The following is quoted from the Zynq UltraScale TRM: When transmit is disabled, with bit [3] of the network control register set low, the transmit-buffer queue pointer resets to point to the address indicated by the transmit-buffer queue base address register. Disabling receive does not have the same effect on the receive-buffer queue pointer. Additionally, there is no need to reset the RBQP and TBQP registers in a phy event callback. Therefore, move macb_init_buffers() to macb_open(). In a phy link up event, the only required action is to reset the tx software head and tail pointers to align with the hardware's behavior. [1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm Fixes: 99537d5c476c ("net: macb: Relocate mog_init_rings() callback from macb_mac_link_up() to macb_open()") Signed-off-by: Kevin Hao Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20260208-macb-init-ring-v1-1-939a32c14635@gmail.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

octeontx2-af: CGX: fix bitmap leaks

2026-03-04T12:20:54Z

[ Upstream commit 3def995c4ede842adf509c410e92d09a0cedc965 ] The RX/TX flow-control bitmaps (rx_fc_pfvf_bmap and tx_fc_pfvf_bmap) are allocated by cgx_lmac_init() but never freed in cgx_lmac_exit(). Unbinding and rebinding the driver therefore triggers kmemleak: unreferenced object (size 16): backtrace: rvu_alloc_bitmap cgx_probe Free both bitmaps during teardown. Fixes: e740003874ed ("octeontx2-af: Flow control resource management") Cc: stable@vger.kernel.org Signed-off-by: Bo Sun Reviewed-by: Vadim Fedorenko Reviewed-by: Jijie Shao Link: https://patch.msgid.link/20260206130925.1087588-2-bo@mboxify.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: wan/fsl_ucc_hdlc: Fix dma_free_coherent() in uhdlc_memclean()

2026-03-04T12:20:54Z

[ Upstream commit 36bd7d5deef936c4e1e3cd341598140e5c14c1d3 ] The priv->rx_buffer and priv->tx_buffer are alloc'd together as contiguous buffers in uhdlc_init() but freed as two buffers in uhdlc_memclean(). Change the cleanup to only call dma_free_coherent() once on the whole buffer. Reviewed-by: Christophe Leroy (CS GROUP) Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Cc: Signed-off-by: Thomas Fourier Link: https://patch.msgid.link/20260206085334.21195-2-fourier.thomas@gmail.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: ethernet: marvell: skge: remove incorrect conflicting PCI ID

2026-03-04T12:20:53Z

[ Upstream commit d01103fdcb871fd83fd06ef5803d576507c6a801 ] The ID 1186:4302 is matched by both r8169 and skge. The same device ID should not be in more than one driver, because in that case, which driver is used is unpredictable. I downloaded the latest drivers for all hardware revisions of the D-Link DGE-530T from D-Link's website, and the only drivers which contain this ID are Realtek drivers. Therefore, remove this device ID from skge. In the kernel bug report which requested addition of this device ID, someone created a patch to add the ID to skge. Then, it was pointed out that this device is an "r8169 in disguise", and a patch was created to add it to r8169. Somehow, both of these patches got merged. See the link below. Link: https://bugzilla.kernel.org/show_bug.cgi?id=38862 Fixes: c074304c2bcf ("add pci-id for DGE-530T") Cc: stable@vger.kernel.org Signed-off-by: Ethan Nelson-Moore Link: https://patch.msgid.link/20260206071724.15268-1-enelsonmoore@gmail.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: cpsw_new: Fix unnecessary netdev unregistration in cpsw_probe() error path

2026-03-04T12:20:52Z

[ Upstream commit 62db84b7efa63b78aed9fdbdae90f198771be94c ] The current error handling in cpsw_probe() has two issues: - cpsw_unregister_ports() may be called before cpsw_register_ports() has been executed. - cpsw_unregister_ports() is already invoked within cpsw_register_ports() in case of a register_netdev() failure, but the error path would call it again. Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Kevin Hao Cc: stable@vger.kernel.org Reviewed-by: Alexander Sverdlin Link: https://patch.msgid.link/20260205-cpsw-error-path-v1-1-6e58bae6b299@gmail.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

dpaa2-switch: validate num_ifs to prevent out-of-bounds write

2026-03-04T12:20:41Z

[ Upstream commit 8a5752c6dcc085a3bfc78589925182e4e98468c5 ] The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ... Fixes: 539dda3c5d19 ("staging: dpaa2-switch: properly setup switching domains") Signed-off-by: Junrui Luo Reviewed-by: Ioana Ciornei Link: https://patch.msgid.link/SYBPR01MB78812B47B7F0470B617C408AAF74A@SYBPR01MB7881.ausprd01.prod.outlook.com Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: usb: pegasus: enable basic endpoint checking

2026-03-04T12:20:41Z

[ Upstream commit 3d7e6ce34f4fcc7083510c28b17a7c36462a25d4 ] pegasus_probe() fills URBs with hardcoded endpoint pipes without verifying the endpoint descriptors: - usb_rcvbulkpipe(dev, 1) for RX data - usb_sndbulkpipe(dev, 2) for TX data - usb_rcvintpipe(dev, 3) for status interrupts A malformed USB device can present these endpoints with transfer types that differ from what the driver assumes. Add a pegasus_usb_ep enum for endpoint numbers, replacing magic constants throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints() calls before any resource allocation to verify endpoint types before use, rejecting devices with mismatched descriptors at probe time, and avoid triggering assertion. Similar fix to - commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking") - commit 9e7021d2aeae ("net: usb: catc: enable basic endpoint checking") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ziyi Guo Reviewed-by: Simon Horman Link: https://patch.msgid.link/20260222050633.410165-1-n7l8m4@u.northwestern.edu Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin

net: wan: farsync: Fix use-after-free bugs caused by unfinished tasklets

2026-03-04T12:20:41Z

[ Upstream commit bae8a5d2e759da2e0cba33ab2080deee96a09373 ] When the FarSync T-series card is being detached, the fst_card_info is deallocated in fst_remove_one(). However, the fst_tx_task or fst_int_task may still be running or pending, leading to use-after-free bugs when the already freed fst_card_info is accessed in fst_process_tx_work_q() or fst_process_int_work_q(). A typical race condition is depicted below: CPU 0 (cleanup) | CPU 1 (tasklet) | fst_start_xmit() fst_remove_one() | tasklet_schedule() unregister_hdlc_device()| | fst_process_tx_work_q() //handler kfree(card) //free | do_bottom_half_tx() | card-> //use The following KASAN trace was captured: ================================================================== BUG: KASAN: slab-use-after-free in do_bottom_half_tx+0xb88/0xd00 Read of size 4 at addr ffff88800aad101c by task ksoftirqd/3/32 ... Call Trace: dump_stack_lvl+0x55/0x70 print_report+0xcb/0x5d0 ? do_bottom_half_tx+0xb88/0xd00 kasan_report+0xb8/0xf0 ? do_bottom_half_tx+0xb88/0xd00 do_bottom_half_tx+0xb88/0xd00 ? _raw_spin_lock_irqsave+0x85/0xe0 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? __pfx___hrtimer_run_queues+0x10/0x10 fst_process_tx_work_q+0x67/0x90 tasklet_action_common+0x1fa/0x720 ? hrtimer_interrupt+0x31f/0x780 handle_softirqs+0x176/0x530 __irq_exit_rcu+0xab/0xe0 sysvec_apic_timer_interrupt+0x70/0x80 ... Allocated by task 41 on cpu 3 at 72.330843s: kasan_save_stack+0x24/0x50 kasan_save_track+0x17/0x60 __kasan_kmalloc+0x7f/0x90 fst_add_one+0x1a5/0x1cd0 local_pci_probe+0xdd/0x190 pci_device_probe+0x341/0x480 really_probe+0x1c6/0x6a0 __driver_probe_device+0x248/0x310 driver_probe_device+0x48/0x210 __device_attach_driver+0x160/0x320 bus_for_each_drv+0x101/0x190 __device_attach+0x198/0x3a0 device_initial_probe+0x78/0xa0 pci_bus_add_device+0x81/0xc0 pci_bus_add_devices+0x7e/0x190 enable_slot+0x9b9/0x1130 acpiphp_check_bridge.part.0+0x2e1/0x460 acpiphp_hotplug_notify+0x36c/0x3c0 acpi_device_hotplug+0x203/0xb10 acpi_hotplug_work_fn+0x59/0x80 ... Freed by task 41 on cpu 1 at 75.138639s: kasan_save_stack+0x24/0x50 kasan_save_track+0x17/0x60 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x43/0x70 kfree+0x135/0x410 fst_remove_one+0x2ca/0x540 pci_device_remove+0xa6/0x1d0 device_release_driver_internal+0x364/0x530 pci_stop_bus_device+0x105/0x150 pci_stop_and_remove_bus_device+0xd/0x20 disable_slot+0x116/0x260 acpiphp_disable_and_eject_slot+0x4b/0x190 acpiphp_hotplug_notify+0x230/0x3c0 acpi_device_hotplug+0x203/0xb10 acpi_hotplug_work_fn+0x59/0x80 ... The buggy address belongs to the object at ffff88800aad1000 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 28 bytes inside of freed 1024-byte region The buggy address belongs to the physical page: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xaad0 head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0 flags: 0x100000000000040(head|node=0|zone=1) page_type: f5(slab) raw: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000 raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000 head: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000 head: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000 head: 0100000000000003 ffffea00002ab401 00000000ffffffff 00000000ffffffff head: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88800aad0f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800aad0f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff88800aad1000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88800aad1080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800aad1100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fix this by ensuring that both fst_tx_task and fst_int_task are properly canceled before the fst_card_info is released. Add tasklet_kill() in fst_remove_one() to synchronize with any pending or running tasklets. Since unregister_hdlc_device() stops data transmission and reception, and fst_disable_intr() prevents further interrupts, it is appropriate to place tasklet_kill() after these calls. The bugs were identified through static analysis. To reproduce the issue and validate the fix, a FarSync T-series card was simulated in QEMU and delays(e.g., mdelay()) were introduced within the tasklet handler to increase the likelihood of triggering the race condition. Fixes: 2f623aaf9f31 ("net: farsync: Fix kmemleak when rmmods farsync") Signed-off-by: Duoming Zhou Reviewed-by: Jijie Shao Link: https://patch.msgid.link/20260219124637.72578-1-duoming@zju.edu.cn Signed-off-by: Paolo Abeni Signed-off-by: Sasha Levin