kernel/drivers/net/wireless/ralink/rt2x00/rt2800usb.c, branch linux-6.2.y

wifi: mac80211: add wake_tx_queue callback to drivers

2022-10-10T09:00:03Z

mac80211 is fully switching over to the internal TX queue (iTXQ) implementation. Update all drivers not yet providing the now mandatory wake_tx_queue() callback. As an side effect the netdev interfaces of all updated drivers will switch to the noqueue qdisc. Signed-off-by: Alexander Wetzel [add staging drivers] Signed-off-by: Johannes Berg

rt2x00: remove duplicate USB device ID

2021-09-21T15:09:38Z

The device 0x043e,0x7a32 is already on the list under CONFIG_RT2800USB_RT55XX. Since it is the sole Arcadyan entry in RT55xx, assume the proper chip is RT55xx, not RT53xx, although this was not confirmed by testing or 3rd party sources. Signed-off-by: Krzysztof Kozlowski Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20210917092108.19497-3-krzysztof.kozlowski@canonical.com

module: remove never implemented MODULE_SUPPORTED_DEVICE

2021-03-17T20:16:18Z

MODULE_SUPPORTED_DEVICE was added in pre-git era and never was implemented. We can safely remove it, because the kernel has grown to have many more reliable mechanisms to determine if device is supported or not. Signed-off-by: Leon Romanovsky Signed-off-by: Linus Torvalds

rt2800usb: add Sweex LW163V2 id's

2021-02-08T11:21:24Z

Add support for Sweex LW163V2 device. Signed-off-by: Stanislaw Gruszka Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20210204101902.199590-1-stf_xl@wp.pl

rt2x00: Use fallthrough pseudo-keyword

2020-08-27T13:05:48Z

Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva Signed-off-by: Kalle Valo Link: https://lore.kernel.org/r/20200821062052.GA8618@embeddedor

rt2x00: implement reconfig_complete

2019-12-18T18:55:55Z

mac80211 has .reconfig_complete that can be used as indicator of HW restart end. This will allow to configure keys/IV differently for HW restart and normal configuration. Signed-off-by: Stanislaw Gruszka Signed-off-by: Kalle Valo

rt2800usb: Add new rt2800usb device PLANEX GW-USMicroN

2019-08-06T12:40:20Z

This patch add a device ID for PLANEX GW-USMicroN. Without this patch, I had to echo the device IDs in order to recognize the device. # lsusb |grep PLANEX Bus 002 Device 005: ID 2019:ed14 PLANEX GW-USMicroN Signed-off-by: Masanari Iida Acked-by: Stanislaw Gruszka Signed-off-by: Kalle Valo

rt2800: add pre_reset_hw callback

2019-06-25T05:10:10Z

Add routine to cleanup interfaces data before hw reset as ieee80211_restart_hw() will do setup interfaces again. Signed-off-by: Stanislaw Gruszka Signed-off-by: Kalle Valo

rt2800: initial watchdog implementation

2019-06-25T05:10:09Z

Add watchdog for rt2800 devices. For now it only detect hung and print error. [Note: I verified that printing messages from process context is fine on MT7620 (WT3020) platform that have problem when printk is called from interrupt context]. Signed-off-by: Stanislaw Gruszka Signed-off-by: Kalle Valo

rt2800: add helpers for reading dma done index

2019-06-25T05:10:08Z

For mmio we do not properlly trace dma done Q_INDEX_DMA_DONE index for TX queues. That would require implementing INT_SOURCE_CSR_*_DMA_DONE interrupts, what is rather not worth to do due to adding extra CPU load (small but still somewhat not necessary otherwise). We can just read TX DMA done indexes from registers directly. What will be used by watchdog. Signed-off-by: Stanislaw Gruszka Signed-off-by: Kalle Valo