kernel/drivers/net/wireless/mediatek/mt76/mt76x02_phy.c, branch linux-6.9.y

wifi: mt76: mt76x02: simplify struct mt76x02_rate_power

2022-12-01T16:29:12Z

- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same values as HT/VHT - reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT Signed-off-by: Felix Fietkau

wifi: mt76: move mt76_rate_power from core to mt76x02 driver code

2022-12-01T16:29:12Z

Its layout and code is mt76x02 specific Signed-off-by: Felix Fietkau

mt76: move chainmask in mt76_phy

2021-01-26T19:07:48Z

Move chainmask from driver phy to mt76_phy since it is used by all drivers. This is a preliminary patch to create a common mcu library used by mt7615 and mt7921 drivers Co-developed-by: Sean Wang Signed-off-by: Sean Wang Signed-off-by: Lorenzo Bianconi Signed-off-by: Felix Fietkau

mt76: move chainmask back to driver specific structs

2020-02-14T09:03:09Z

Nothing in the core uses it Signed-off-by: Felix Fietkau

mt76: switch to SPDX tag instead of verbose boilerplate text

2019-09-05T15:42:31Z

No functional change intended. Add SPDX identifiers to all remaining files in /mt76. Signed-off-by: Ryder Lee Signed-off-by: Felix Fietkau

mt76: mt76x02: fix some checkpatch warnings

2019-09-05T15:42:31Z

This fixes the following checkpatch warnings: ERROR: code indent should use tabs where possible CHECK: Alignment should match open parenthesis CHECK: No space is necessary after a cast CHECK: Please don't use multiple blank lines CHECK: Avoid precedence issues in macro WARNING: Statements should start on a tabstop WARNING: Unnecessary space before function pointer arguments Signed-off-by: Ryder Lee Signed-off-by: Felix Fietkau

mt76: mt76x02: reduce false positives in ED/CCA tx blocking

2019-03-07T11:50:23Z

Full tx blocking (as opposed to CCA blocking) should only happen if there is a continuous non-802.11 signal above the energy detect threshold. Unfortunately the ED/CCA counter can't detect that, as it also counts 802.11 signals as busy. Similar to the vendor code, implement a learning mode that waits until the AGC gain has already been adjusted to the lowest value (due to false CCA events), and the number of false CCA events still remains high, and the blocking threshold is exceeded for more than 5 seconds. Signed-off-by: Felix Fietkau

mt76: move mt76x02_phy_get_min_avg_rssi to mt76 core

2019-01-17T13:50:15Z

This will be used by mt7603 as well Signed-off-by: Felix Fietkau

mt76x02: run calibration after scanning

2018-11-30T11:21:43Z

If we are associated and scanning is performed, sw_scan_complete callback is done after we get back to operating channel, so we do not perform queue cal work. Fix this queue cal work from sw_scan_complete(). On mt76x0 we have to restore gain in MT_BBP(AGC, 8) register after scanning, as it was multiple times modified by channel switch code. So queue cal work without any delay to set AGC gain value. Similar like in mt76x2 init AGC gain only when set operating channel and just check before queuing cal work in sw_scan_complete() if initialization was already done. Fixes: bbd10586f0df ("mt76x0: phy: do not run calibration during channel switch") Signed-off-by: Stanislaw Gruszka Signed-off-by: Felix Fietkau

mt76: introduce mt76x02_init_agc_gain routine

2018-10-13T15:39:50Z

Add mt76x02_init_agc_gain routine in mt76x02-lib moudule in order to be reused by mt76x0 for vga initalization Signed-off-by: Lorenzo Bianconi Signed-off-by: Felix Fietkau