kernel/drivers/net/phy/realtek.c, branch linux-5.1.y

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2019-02-24T20:06:19Z

Three conflicts, one of which, for marvell10g.c is non-trivial and requires some follow-up from Heiner or someone else. The issue is that Heiner converted the marvell10g driver over to use the generic c45 code as much as possible. However, in 'net' a bug fix appeared which makes sure that a new local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0 is cleared. Signed-off-by: David S. Miller

net: phy: realtek: Dummy IRQ calls for RTL8366RB

2019-02-24T02:45:28Z

This fixes a regression introduced by commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7 "net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt". This assumes that a PHY cannot trigger interrupt unless it has .config_intr() or .ack_interrupt() implemented. A later patch makes the code assume both need to be implemented for interrupts to be present. But this PHY (which is inside a DSA) will happily fire interrupts without either callback. Implement dummy callbacks for .config_intr() and .ack_interrupt() in the phy header to fix this. Tested on the RTL8366RB on D-Link DIR-685. Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit Signed-off-by: Linus Walleij Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: realtek: add generic Realtek PHY driver

2019-02-03T17:37:08Z

The integrated PHY's of later RTL8168 network chips report the generic PHYID 0x001cc800 (Realtek OUI, model and revision number both set to zero) and therefore currently the genphy driver is used. To be able to use the paged version of e.g. phy_write() we need a PHY driver with the read_page and write_page callbacks implemented. So basically make a copy of the genphy driver, just with the read_page and write_page callbacks being set. Signed-off-by: Heiner Kallweit Signed-off-by: David S. Miller

net: phy: Convert some PHY and MDIO driver files to SPDX headers

2019-01-23T04:53:08Z

Where the license text and the MODULE_LICENSE() value agree, convert to using an SPDX header, removing the license text. Signed-off-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: realtek: use new PHYID matching macros

2018-11-11T17:44:14Z

Use new macros for PHYID matching to avoid boilerplate code. Signed-off-by: Heiner Kallweit Signed-off-by: David S. Miller

net: phy: remove flag PHY_HAS_INTERRUPT from driver configs

2018-11-11T17:36:56Z

Now that flag PHY_HAS_INTERRUPT has been replaced with a check for callbacks config_intr and ack_interrupt, we can remove setting this flag from all driver configs. Last but not least remove flag PHY_HAS_INTERRUPT completely. Signed-off-by: Heiner Kallweit Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: realtek: load driver for all PHYs with a Realtek OUI

2018-11-08T06:18:58Z

Instead of listing every single PHYID, load the driver for every PHYID with a Realtek OUI, independent of model number and revision. This patch also improves two further aspects: - constify realtek_tbl[] - the mask should have been 0xffffffff instead of 0x001fffff so far, by masking out some bits a PHY from another vendor could have been matched Signed-off-by: Heiner Kallweit Signed-off-by: David S. Miller

net: phy: realtek: fix RTL8201F sysfs name

2018-11-05T00:43:17Z

Since 4.19 the following error in sysfs has appeared when using the r8169 NIC driver: $cd /sys/module/realtek/drivers $ls -l ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory [..garbled dir entries follow..] Apparently the forward slash in "10/100Mbps Ethernet" is interpreted as directory separator that leads nowhere, and was introduced in commit 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions"). Fix this by removing the offending slash in the driver name. Other drivers in net/phy seem to have the same problem, but I cannot test/verify them. Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by: Holger Hoffstätte Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller

net: phy: realtek: Support RTL8366RB variant

2018-07-18T04:43:38Z

The RTL8366RB is an ASIC with five internal PHYs for LAN0..LAN3 and WAN. The PHYs are spawn off the main device so they can be handled in a distributed manner by the Realtek PHY driver. All that is really needed is the power save feature enablement and letting the PHY driver core pick up the IRQ from the switch chip. Cc: Antti Seppälä Cc: Roman Yeryomin Cc: Colin Leitner Cc: Gabor Juhos Cc: Florian Fainelli Signed-off-by: Linus Walleij Signed-off-by: David S. Miller

net: phy: realtek: add missing entry for RTL8211C to mdio_device_id table

2018-07-16T20:36:16Z

Add missing entry for RTL8211C to mdio_device_id table. Signed-off-by: Heiner Kallweit Fixes: cf87915cb9f8 ("net: phy: realtek: add support for RTL8211C") Signed-off-by: David S. Miller