kernel/drivers/net/ethernet, branch linux-4.1.y

sky2: Increase D3 delay to sky2 stops working after suspend

2018-05-23T01:36:30Z

[ Upstream commit afb133637071be6deeb8b3d0e55593ffbf63c527 ] The sky2 ethernet stops working after system resume from suspend: [ 582.852065] sky2 0000:04:00.0: Refused to change power state, currently in D3 The current 150ms delay is not enough, change it to 200ms can solve the issue. BugLink: https://bugs.launchpad.net/bugs/1758507 Cc: Stable Signed-off-by: Kai-Heng Feng Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

cxgb4vf: Fix SGE FL buffer initialization logic for 64K pages

2018-05-23T01:36:30Z

[ Upstream commit ea0a42109aee7b92e631c4eb3f2219fadf58acdd ] We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and the extant logic would flag that as an error. This was already fixed in cxgb4 driver with "92ddcc7 cxgb4: Fix some small bugs in t4_sge_init_soft() when our Page Size is 64KB". Original Work by: Casey Leedom Signed-off-by: Arjun Vynipadath Signed-off-by: Ganesh Goudar Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

bnx2x: Allow vfs to disable txvlan offload

2018-05-23T01:36:28Z

[ Upstream commit 92f85f05caa51d844af6ea14ffbc7a786446a644 ] VF clients are configured as enforced, meaning firmware is validating the correctness of their ethertype/vid during transmission. Once txvlan is disabled, VF would start getting SKBs for transmission here vlan is on the payload - but it'll pass the packet's ethertype instead of the vid, leading to firmware declaring it as malicious. Signed-off-by: Yuval Mintz Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: emac: fix reset timeout with AR8035 phy

2018-05-23T01:36:28Z

[ Upstream commit 19d90ece81da802207a9b91ce95a29fbdc40626e ] This patch fixes a problem where the AR8035 PHY can't be detected on an Cisco Meraki MR24, if the ethernet cable is not connected on boot. Russell Senior provided steps to reproduce the issue: |Disconnect ethernet cable, apply power, wait until device has booted, |plug in ethernet, check for interfaces, no eth0 is listed. | |This appears to be a problem during probing of the AR8035 Phy chip. |When ethernet has no link, the phy detection fails, and eth0 is not |created. Plugging ethernet later has no effect, because there is no |interface as far as the kernel is concerned. The relevant part of |the boot log looks like this: |this is the failing case: | |[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode |[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout |[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY! |and the succeeding case: | |[ 0.876672] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode |[ 0.883952] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:01:.. |[ 0.890822] eth0: found Atheros 8035 Gigabit Ethernet PHY (0x01) Based on the comment and the commit message of commit 23fbb5a87c56 ("emac: Fix EMAC soft reset on 460EX/GT"). This is because the AR8035 PHY doesn't provide the TX Clock, if the ethernet cable is not attached. This causes the reset to timeout and the PHY detection code in emac_init_phy() is unable to detect the AR8035 PHY. As a result, the emac driver bails out early and the user left with no ethernet. In order to stay compatible with existing configurations, the driver tries the current reset approach at first. Only if the first attempt timed out, it does perform one more retry with the clock temporarily switched to the internal source for just the duration of the reset. LEDE-Bug: #687 Cc: Chris Blake Reported-by: Russell Senior Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT") Signed-off-by: Christian Lamparter Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

e1000e: Undo e1000e_pm_freeze if __e1000_shutdown fails

2018-05-23T01:36:28Z

[ Upstream commit 833521ebc65b1c3092e5c0d8a97092f98eec595d ] An error during suspend (e100e_pm_suspend), [ 429.994338] ACPI : EC: event blocked [ 429.994633] e1000e: EEE TX LPI TIMER: 00000011 [ 430.955451] pci_pm_suspend(): e1000e_pm_suspend+0x0/0x30 [e1000e] returns -2 [ 430.955454] dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2 [ 430.955458] PM: Device 0000:00:19.0 failed to suspend async: error -2 [ 430.955581] PM: Some devices failed to suspend, or early wake event detected [ 430.957709] ACPI : EC: event unblocked lead to complete failure: [ 432.585002] ------------[ cut here ]------------ [ 432.585013] WARNING: CPU: 3 PID: 8372 at kernel/irq/manage.c:1478 __free_irq+0x9f/0x280 [ 432.585015] Trying to free already-free IRQ 20 [ 432.585016] Modules linked in: cdc_ncm usbnet x86_pkg_temp_thermal intel_powerclamp coretemp mii crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm mei_me mei sdhci_pci sdhci i915 mmc_core e1000e ptp pps_core prime_numbers [ 432.585042] CPU: 3 PID: 8372 Comm: kworker/u16:40 Tainted: G U 4.10.0-rc8-CI-Patchwork_3870+ #1 [ 432.585044] Hardware name: LENOVO 2356GCG/2356GCG, BIOS G7ET31WW (1.13 ) 07/02/2012 [ 432.585050] Workqueue: events_unbound async_run_entry_fn [ 432.585051] Call Trace: [ 432.585058] dump_stack+0x67/0x92 [ 432.585062] __warn+0xc6/0xe0 [ 432.585065] warn_slowpath_fmt+0x4a/0x50 [ 432.585070] ? _raw_spin_lock_irqsave+0x49/0x60 [ 432.585072] __free_irq+0x9f/0x280 [ 432.585075] free_irq+0x34/0x80 [ 432.585089] e1000_free_irq+0x65/0x70 [e1000e] [ 432.585098] e1000e_pm_freeze+0x7a/0xb0 [e1000e] [ 432.585106] e1000e_pm_suspend+0x21/0x30 [e1000e] [ 432.585113] pci_pm_suspend+0x71/0x140 [ 432.585118] dpm_run_callback+0x6f/0x330 [ 432.585122] ? pci_pm_freeze+0xe0/0xe0 [ 432.585125] __device_suspend+0xea/0x330 [ 432.585128] async_suspend+0x1a/0x90 [ 432.585132] async_run_entry_fn+0x34/0x160 [ 432.585137] process_one_work+0x1f4/0x6d0 [ 432.585140] ? process_one_work+0x16e/0x6d0 [ 432.585143] worker_thread+0x49/0x4a0 [ 432.585145] kthread+0x107/0x140 [ 432.585148] ? process_one_work+0x6d0/0x6d0 [ 432.585150] ? kthread_create_on_node+0x40/0x40 [ 432.585154] ret_from_fork+0x2e/0x40 [ 432.585156] ---[ end trace 6712df7f8c4b9124 ]--- The unwind failures stems from commit 2800209994f8 ("e1000e: Refactor PM flows"), but it may be a later patch that introduced the non-recoverable behaviour. Fixes: 2800209994f8 ("e1000e: Refactor PM flows") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99847 Signed-off-by: Chris Wilson Signed-off-by: Jani Nikula Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher Signed-off-by: Sasha Levin

e1000e: fix race condition around skb_tstamp_tx()

2018-05-23T01:36:28Z

[ Upstream commit 5012863b7347866764c4a4e58b62fb05346b0d06 ] The e1000e driver and related hardware has a limitation on Tx PTP packets which requires we limit to timestamping a single packet at once. We do this by verifying that we never request a new Tx timestamp while we still have a tx_hwtstamp_skb pointer. Unfortunately the driver suffers from a race condition around this. The tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx() is called. This function notifies the stack and applications of a new timestamp. Even a well behaved application that only sends a new request when the first one is finished might be woken up and possibly send a packet before we can free the timestamp in the driver again. The result is that we needlessly ignore some Tx timestamp requests in this corner case. Fix this by assigning the tx_hwtstamp_skb pointer prior to calling skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb until that function finishes. This ensures that the application is not woken up until the driver is ready to begin timestamping a new packet. This ensures that well behaved applications do not accidentally race with condition to skip Tx timestamps. Obviously an application which sends multiple Tx timestamp requests at once will still only timestamp one packet at a time. Unfortunately there is nothing we can do about this. Reported-by: David Mirabito Signed-off-by: Jacob Keller Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher Signed-off-by: Sasha Levin

net/mlx4: Fix the check in attaching steering rules

2018-05-23T01:36:27Z

[ Upstream commit 6dc06c08bef1c746ff8da33dab677cfbacdcad32 ] Our previous patch (cited below) introduced a regression for RAW Eth QPs. Fix it by checking if the QP number provided by user-space exists, hence allowing steering rules to be added for valid QPs only. Fixes: 89c557687a32 ("net/mlx4_en: Avoid adding steering rules with invalid ring") Reported-by: Or Gerlitz Signed-off-by: Talat Batheesh Signed-off-by: Tariq Toukan Acked-by: Or Gerlitz Reviewed-by: Leon Romanovsky Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

qlcnic: Fix a sleep-in-atomic bug in qlcnic_82xx_hw_write_wx_2M and qlcnic_82xx_hw_read_wx_2M

2018-05-23T01:36:27Z

[ Upstream commit 5ea6d691aac6c93b790f0905e3460d44cc4c449b ] The driver may sleep under a write spin lock, and the function call path is: qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave) crb_win_lock qlcnic_pcie_sem_lock usleep_range qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave) crb_win_lock qlcnic_pcie_sem_lock usleep_range To fix it, the usleep_range is replaced with udelay. Signed-off-by: Jia-Ju Bai Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: freescale: fix potential null pointer dereference

2018-05-23T01:36:27Z

[ Upstream commit 06d2d6431bc8d41ef5ffd8bd4b52cea9f72aed22 ] Add NULL check before dereferencing pointer _id_ in order to avoid a potential NULL pointer dereference. Addresses-Coverity-ID: 1397995 Signed-off-by: Gustavo A. R. Silva Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

sh_eth: Use platform device for printing before register_netdev()

2018-05-23T01:36:24Z

[ Upstream commit 5f5c5449acad0cd3322e53e1ac68c044483b0aa5 ] The MDIO initialization failure message is printed using the network device, before it has been registered, leading to: (null): failed to initialise MDIO Use the platform device instead to fix this: sh-eth ee700000.ethernet: failed to initialise MDIO Fixes: daacf03f0bbfefee ("sh_eth: Register MDIO bus before registering the network device") Signed-off-by: Geert Uytterhoeven Reviewed-by: Laurent Pinchart Signed-off-by: David S. Miller Signed-off-by: Sasha Levin