kernel/drivers/net/ethernet/nxp, branch linux-4.16.y

net: manual clean code which call skb_put_[data:zero]

2017-06-20T17:30:15Z

Signed-off-by: yuan linyu Signed-off-by: David S. Miller

networking: introduce and use skb_put_data()

2017-06-16T15:48:37Z

A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger Signed-off-by: Johannes Berg Signed-off-by: David S. Miller

drivers: net: generalize napi_complete_done()

2017-01-30T20:10:42Z

napi_complete_done() allows to opt-in for gro_flush_timeout, added back in linux-3.19, commit 3b47d30396ba ("net: gro: add a per device gro flush timer") This allows for more efficient GRO aggregation without sacrifying latencies. Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller

net: deprecate eth_change_mtu, remove usage

2016-10-13T13:36:57Z

With centralized MTU checking, there's nothing productive done by eth_change_mtu that isn't already done in dev_set_mtu, so mark it as deprecated and remove all usage of it in the kernel. All callers have been audited for calls to alloc_etherdev* or ether_setup directly, which means they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu prints out a netdev_warn about being deprecated, for the benefit of out-of-tree drivers that might be utilizing it. Of note, dvb_net.c actually had dev->mtu = 4096, while using eth_change_mtu, meaning that if you ever tried changing it's mtu, you couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set to 4096 to remedy that. v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86 CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson Signed-off-by: David S. Miller

net: lpc_eth: Check clk_prepare_enable() error

2016-08-24T00:10:16Z

clk_prepare_enable() may fail, so we should better check its return value and propagate it in the case of failure While at it, replace __lpc_eth_clock_enable() with a plain clk_prepare_enable/clk_disable_unprepare() call in order to simplify the code. Signed-off-by: Fabio Estevam Acked-by: Vladimir Zapolskiy Signed-off-by: David S. Miller

net: lpc_eth: Remove unused 'pldat' variable

2016-07-05T06:55:29Z

Since commit f786f3564c4f02d5026 ("net: ethernet: lpc_eth: use phydev from struct net_device") the 'pldat' variable became unused, so just remove it. Reported-by: Olof's autobuilder Signed-off-by: Fabio Estevam Signed-off-by: David S. Miller

net: ethernet: lpc_eth: use phy_ethtool_{get|set}_link_ksettings

2016-06-29T12:15:33Z

There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes Signed-off-by: David S. Miller

net: ethernet: lpc_eth: use phydev from struct net_device

2016-06-29T12:15:33Z

The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes Signed-off-by: David S. Miller

net: lpc_eth: Remove unused variables

2016-01-11T03:50:14Z

Commit e7f4dc3536a400 ("mdio: Move allocation of interrupts into core") introduced the following build warnings: drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_mii_init': drivers/net/ethernet/nxp/lpc_eth.c:865:1: warning: label 'err_out_1' defined but not used [-Wunused-label] drivers/net/ethernet/nxp/lpc_eth.c:826:20: warning: unused variable 'i' [-Wunused-variable] Remove the unused variables to fix them. Reported-by: Olof's autobuilder Signed-off-by: Fabio Estevam Acked-by: Andrew Lunn Signed-off-by: David S. Miller

mdio: Move allocation of interrupts into core

2016-01-07T19:31:26Z

Have mdio_alloc() create the array of interrupt numbers, and initialize it to POLLING. This is what most MDIO drivers want, so allowing code to be removed from the drivers. Signed-off-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller