kernel/drivers/net/ethernet/intel, branch linux-rolling-stable

ice: fix retry for AQ command 0x06EE

2026-03-19T15:15:18Z

commit fb4903b3354aed4a2301180cf991226f896c87ed upstream. Executing ethtool -m can fail reporting a netlink I/O error while firmware link management holds the i2c bus used to communicate with the module. According to Intel(R) Ethernet Controller E810 Datasheet Rev 2.8 [1] Section 3.3.10.4 Read/Write SFF EEPROM (0x06EE) request should to be retried upon receiving EBUSY from firmware. Commit e9c9692c8a81 ("ice: Reimplement module reads used by ethtool") implemented it only for part of ice_get_module_eeprom(), leaving all other calls to ice_aq_sff_eeprom() vulnerable to returning early on getting EBUSY without retrying. Remove the retry loop from ice_get_module_eeprom() and add Admin Queue (AQ) command with opcode 0x06EE to the list of commands that should be retried on receiving EBUSY from firmware. Cc: stable@vger.kernel.org Fixes: e9c9692c8a81 ("ice: Reimplement module reads used by ethtool") Signed-off-by: Jakub Staniszewski Co-developed-by: Dawid Osuchowski Signed-off-by: Dawid Osuchowski Reviewed-by: Aleksandr Loktionov Reviewed-by: Przemek Kitszel Link: https://www.intel.com/content/www/us/en/content-details/613875/intel-ethernet-controller-e810-datasheet.html [1] Reviewed-by: Paul Menzel Tested-by: Rinitha S (A Contingent worker at Intel) Signed-off-by: Tony Nguyen Signed-off-by: Greg Kroah-Hartman

ixgbevf: fix link setup issue

2026-03-19T15:15:16Z

commit feae40a6a178bb525a15f19288016e5778102a99 upstream. It may happen that VF spawned for E610 adapter has problem with setting link up. This happens when ixgbevf supporting mailbox API 1.6 cooperates with PF driver which doesn't support this version of API, and hence doesn't support new approach for getting PF link data. In that case VF asks PF to provide link data but as PF doesn't support it, returns -EOPNOTSUPP what leads to early bail from link configuration sequence. Avoid such situation by using legacy VFLINKS approach whenever negotiated API version is less than 1.6. To reproduce the issue just create VF and set its link up - adapter must be any from the E610 family, ixgbevf must support API 1.6 or higher while ixgbevf must not. Fixes: 53f0eb62b4d2 ("ixgbevf: fix getting link speed data for E610 devices") Reviewed-by: Aleksandr Loktionov Reviewed-by: Piotr Kwapulinski Reviewed-by: Paul Menzel Cc: stable@vger.kernel.org Signed-off-by: Jedrzej Jagielski Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen Signed-off-by: Greg Kroah-Hartman

ice: reintroduce retry mechanism for indirect AQ

2026-03-19T15:15:16Z

commit 326256c0a72d4877cec1d4df85357da106233128 upstream. Add retry mechanism for indirect Admin Queue (AQ) commands. To do so we need to keep the command buffer. This technically reverts commit 43a630e37e25 ("ice: remove unused buffer copy code in ice_sq_send_cmd_retry()"), but combines it with a fix in the logic by using a kmemdup() call, making it more robust and less likely to break in the future due to programmer error. Cc: Michal Schmidt Cc: stable@vger.kernel.org Fixes: 3056df93f7a8 ("ice: Re-send some AQ commands, as result of EBUSY AQ error") Signed-off-by: Jakub Staniszewski Co-developed-by: Dawid Osuchowski Signed-off-by: Dawid Osuchowski Reviewed-by: Aleksandr Loktionov Reviewed-by: Przemek Kitszel Reviewed-by: Paul Menzel Tested-by: Rinitha S (A Contingent worker at Intel) Signed-off-by: Tony Nguyen Signed-off-by: Greg Kroah-Hartman

e1000/e1000e: Fix leak in DMA error cleanup

2026-03-19T15:14:56Z

[ Upstream commit e94eaef11142b01f77bf8ba4d0b59720b7858109 ] If an error is encountered while mapping TX buffers, the driver should unmap any buffers already mapped for that skb. Because count is incremented after a successful mapping, it will always match the correct number of unmappings needed when dma_error is reached. Decrementing count before the while loop in dma_error causes an off-by-one error. If any mapping was successful before an unsuccessful mapping, exactly one DMA mapping would leak. In these commits, a faulty while condition caused an infinite loop in dma_error: Commit 03b1320dfcee ("e1000e: remove use of skb_dma_map from e1000e driver") Commit 602c0554d7b0 ("e1000: remove use of skb_dma_map from e1000 driver") Commit c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()") fixed the infinite loop, but introduced the off-by-one error. This issue may still exist in the igbvf driver, but I did not address it in this patch. Fixes: c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()") Assisted-by: Claude:claude-4.6-opus Signed-off-by: Matt Vollrath Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

i40e: fix src IP mask checks and memcpy argument names in cloud filter

2026-03-19T15:14:56Z

[ Upstream commit e809085f492842ce7a519c9ef72d40f4bca89c13 ] Fix following issues in the IPv4 and IPv6 cloud filter handling logic in both the add and delete paths: - The source-IP mask check incorrectly compares mask.src_ip[0] against tcf.dst_ip[0]. Update it to compare against tcf.src_ip[0]. This likely goes unnoticed because the check is in an "else if" path that only executes when dst_ip is not set, most cloud filter use cases focus on destination-IP matching, and the buggy condition can accidentally evaluate true in some cases. - memcpy() for the IPv4 source address incorrectly uses ARRAY_SIZE(tcf.dst_ip) instead of ARRAY_SIZE(tcf.src_ip), although both arrays are the same size. - The IPv4 memcpy operations used ARRAY_SIZE(tcf.dst_ip) and ARRAY_SIZE (tcf.src_ip), Update these to use sizeof(cfilter->ip.v4.dst_ip) and sizeof(cfilter->ip.v4.src_ip) to ensure correct and explicit copy size. - In the IPv6 delete path, memcmp() uses sizeof(src_ip6) when comparing dst_ip6 fields. Replace this with sizeof(dst_ip6) to make the intent explicit, even though both fields are struct in6_addr. Fixes: e284fc280473 ("i40e: Add and delete cloud filter") Signed-off-by: Alok Tiwari Reviewed-by: Aleksandr Loktionov Reviewed-by: Paul Menzel Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

iavf: fix incorrect reset handling in callbacks

2026-03-19T15:14:56Z

[ Upstream commit fdadbf6e84c44df8dbb85cfdd38bc10e4431501d ] Three driver callbacks schedule a reset and wait for its completion: ndo_change_mtu(), ethtool set_ringparam(), and ethtool set_channels(). Waiting for reset in ndo_change_mtu() and set_ringparam() was added by commit c2ed2403f12c ("iavf: Wait for reset in callbacks which trigger it") to fix a race condition where adding an interface to bonding immediately after MTU or ring parameter change failed because the interface was still in __RESETTING state. The same commit also added waiting in iavf_set_priv_flags(), which was later removed by commit 53844673d555 ("iavf: kill "legacy-rx" for good"). Waiting in set_channels() was introduced earlier by commit 4e5e6b5d9d13 ("iavf: Fix return of set the new channel count") to ensure the PF has enough time to complete the VF reset when changing channel count, and to return correct error codes to userspace. Commit ef490bbb2267 ("iavf: Add net_shaper_ops support") added net_shaper_ops to iavf, which required reset_task to use _locked NAPI variants (napi_enable_locked, napi_disable_locked) that need the netdev instance lock. Later, commit 7e4d784f5810 ("net: hold netdev instance lock during rtnetlink operations") and commit 2bcf4772e45a ("net: ethtool: try to protect all callback with netdev instance lock") started holding the netdev instance lock during ndo and ethtool callbacks for drivers with net_shaper_ops. Finally, commit 120f28a6f314 ("iavf: get rid of the crit lock") replaced the driver's crit_lock with netdev_lock in reset_task, causing incorrect behavior: the callback holds netdev_lock and waits for reset_task, but reset_task needs the same lock: Thread 1 (callback) Thread 2 (reset_task) ------------------- --------------------- netdev_lock() [blocked on workqueue] ndo_change_mtu() or ethtool op iavf_schedule_reset() iavf_wait_for_reset() iavf_reset_task() waiting... netdev_lock() <- blocked This does not strictly deadlock because iavf_wait_for_reset() uses wait_event_interruptible_timeout() with a 5-second timeout. The wait eventually times out, the callback returns an error to userspace, and after the lock is released reset_task completes the reset. This leads to incorrect behavior: userspace sees an error even though the configuration change silently takes effect after the timeout. Fix this by extracting the reset logic from iavf_reset_task() into a new iavf_reset_step() function that expects netdev_lock to be already held. The three callbacks now call iavf_reset_step() directly instead of scheduling the work and waiting, performing the reset synchronously in the caller's context which already holds netdev_lock. This eliminates both the incorrect error reporting and the need for iavf_wait_for_reset(), which is removed along with the now-unused reset_waitqueue. The workqueue-based iavf_reset_task() becomes a thin wrapper that acquires netdev_lock and calls iavf_reset_step(), preserving its use for PF-initiated resets. The callbacks may block for several seconds while iavf_reset_step() polls hardware registers, but this is acceptable since netdev_lock is a per-device mutex and only serializes operations on the same interface. v3: - Remove netif_running() guard from iavf_set_channels(). Unlike set_ringparam where descriptor counts are picked up by iavf_open() directly, num_req_queues is only consumed during iavf_reinit_interrupt_scheme() in the reset path. Skipping the reset on a down device would silently discard the channel count change. - Remove dead reset_waitqueue code (struct field, init, and all wake_up calls) since iavf_wait_for_reset() was the only consumer. Fixes: 120f28a6f314 ("iavf: get rid of the crit lock") Reviewed-by: Jacob Keller Signed-off-by: Petr Oros Reviewed-by: Przemek Kitszel Tested-by: Rafal Romanowski Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

iavf: fix PTP use-after-free during reset

2026-03-19T15:14:56Z

[ Upstream commit efc54fb13d79117a825fef17364315a58682c7ec ] Commit 7c01dbfc8a1c5f ("iavf: periodically cache PHC time") introduced a worker to cache PHC time, but failed to stop it during reset or disable. This creates a race condition where `iavf_reset_task()` or `iavf_disable_vf()` free adapter resources (AQ) while the worker is still running. If the worker triggers `iavf_queue_ptp_cmd()` during teardown, it accesses freed memory/locks, leading to a crash. Fix this by calling `iavf_ptp_release()` before tearing down the adapter. This ensures `ptp_clock_unregister()` synchronously cancels the worker and cleans up the chardev before the backing resources are destroyed. Fixes: 7c01dbfc8a1c5f ("iavf: periodically cache PHC time") Signed-off-by: Petr Oros Reviewed-by: Ivan Vecera Acked-by: Jacob Keller Reviewed-by: Vadim Fedorenko Reviewed-by: Paul Menzel Reviewed-by: Aleksandr Loktionov Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

drivers: net: ice: fix devlink parameters get without irdma

2026-03-19T15:14:56Z

[ Upstream commit bd98c6204d1195973b1760fe45860863deb6200c ] If CONFIG_IRDMA isn't enabled but there are ice NICs in the system, the driver will prevent full devlink dev param show dump because its rdma get callbacks return ENODEV and stop the dump. For example: $ devlink dev param show pci/0000:82:00.0: name msix_vec_per_pf_max type generic values: cmode driverinit value 2 name msix_vec_per_pf_min type generic values: cmode driverinit value 2 kernel answers: No such device Returning EOPNOTSUPP allows the dump to continue so we can see all devices' devlink parameters. Fixes: c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers") Signed-off-by: Nikolay Aleksandrov Tested-by: Rinitha S (A Contingent worker at Intel) Signed-off-by: Tony Nguyen Signed-off-by: Sasha Levin

i40e: use xdp.frame_sz as XDP RxQ info frag_size

2026-03-12T11:10:00Z

[ Upstream commit c69d22c6c46a1d792ba8af3d8d6356fdc0e6f538 ] The only user of frag_size field in XDP RxQ info is bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead of DMA write size. Different assumptions in i40e driver configuration lead to negative tailroom. Set frag_size to the same value as frame_sz in shared pages mode, use new helper to set frag_size when AF_XDP ZC is active. Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size") Reviewed-by: Aleksandr Loktionov Signed-off-by: Larysa Zaremba Link: https://patch.msgid.link/20260305111253.2317394-7-larysa.zaremba@intel.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

i40e: fix registering XDP RxQ info

2026-03-12T11:10:00Z

[ Upstream commit 8f497dc8a61429cc004720aa8e713743355d80cf ] Current way of handling XDP RxQ info in i40e has a problem, where frag_size is not updated when xsk_buff_pool is detached or when MTU is changed, this leads to growing tail always failing for multi-buffer packets. Couple XDP RxQ info registering with buffer allocations and unregistering with cleaning the ring. Fixes: a045d2f2d03d ("i40e: set xdp_rxq_info::frag_size") Reviewed-by: Aleksandr Loktionov Signed-off-by: Larysa Zaremba Link: https://patch.msgid.link/20260305111253.2317394-6-larysa.zaremba@intel.com Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin