kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h, branch linux-6.18.y

ixgbe: Correct BASE-BX10 compliance code

2024-12-03T18:11:53Z

SFF-8472 (section 5.4 Transceiver Compliance Codes) defines bit 6 as BASE-BX10. Bit 6 means a value of 0x40 (decimal 64). The current value in the source code is 0x64, which appears to be a mix-up of hex and decimal values. A value of 0x64 (binary 01100100) incorrectly sets bit 2 (1000BASE-CX) and bit 5 (100BASE-FX) as well. Fixes: 1b43e0d20f2d ("ixgbe: Add 1000BASE-BX support") Signed-off-by: Tore Amundsen Reviewed-by: Paul Menzel Acked-by: Ernesto Castellotti Tested-by: Pucha Himasekhar Reddy (A Contingent worker at Intel) Signed-off-by: Tony Nguyen

ixgbe: Add 1000BASE-BX support

2024-03-05T04:49:58Z

Added support for 1000BASE-BX, i.e. Gigabit Ethernet over single strand of single-mode fiber. The initialization of a 1000BASE-BX SFP is the same as 1000BASE-SX/LX with the only difference that the Bit Rate Nominal Value must be checked to make sure it is a Gigabit Ethernet transceiver, as described by the SFF-8472 specification. This was tested with the FS.com SFP-GE-BX 1310/1490nm 10km transceiver: $ ethtool -m eth4 Identifier : 0x03 (SFP) Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID) Connector : 0x07 (LC) Transceiver codes : 0x00 0x00 0x00 0x40 0x00 0x00 0x00 0x00 0x00 Transceiver type : Ethernet: BASE-BX10 Encoding : 0x01 (8B/10B) BR, Nominal : 1300MBd Rate identifier : 0x00 (unspecified) Length (SMF,km) : 10km Length (SMF) : 10000m Length (50um) : 0m Length (62.5um) : 0m Length (Copper) : 0m Length (OM3) : 0m Laser wavelength : 1310nm Vendor name : FS Vendor OUI : 64:9d:99 Vendor PN : SFP-GE-BX Vendor rev : Option values : 0x20 0x0a Option : RX_LOS implemented Option : TX_FAULT implemented Option : Power level 3 requirement BR margin, max : 0% BR margin, min : 0% Vendor SN : S2202359108 Date code : 220307 Optical diagnostics support : Yes Laser bias current : 17.650 mA Laser output power : 0.2132 mW / -6.71 dBm Receiver signal average optical power : 0.2740 mW / -5.62 dBm Module temperature : 47.30 degrees C / 117.13 degrees F Module voltage : 3.2576 V Alarm/warning flags implemented : Yes Laser bias current high alarm : Off Laser bias current low alarm : Off Laser bias current high warning : Off Laser bias current low warning : Off Laser output power high alarm : Off Laser output power low alarm : Off Laser output power high warning : Off Laser output power low warning : Off Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : Off Laser rx power high warning : Off Laser rx power low warning : Off Laser bias current high alarm threshold : 110.000 mA Laser bias current low alarm threshold : 1.000 mA Laser bias current high warning threshold : 100.000 mA Laser bias current low warning threshold : 1.000 mA Laser output power high alarm threshold : 0.7079 mW / -1.50 dBm Laser output power low alarm threshold : 0.0891 mW / -10.50 dBm Laser output power high warning threshold : 0.6310 mW / -2.00 dBm Laser output power low warning threshold : 0.1000 mW / -10.00 dBm Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F Module temperature low alarm threshold : -45.00 degrees C / -49.00 degrees F Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F Module temperature low warning threshold : -40.00 degrees C / -40.00 degrees F Module voltage high alarm threshold : 3.7950 V Module voltage low alarm threshold : 2.8050 V Module voltage high warning threshold : 3.4650 V Module voltage low warning threshold : 3.1350 V Laser rx power high alarm threshold : 0.7079 mW / -1.50 dBm Laser rx power low alarm threshold : 0.0028 mW / -25.53 dBm Laser rx power high warning threshold : 0.6310 mW / -2.00 dBm Laser rx power low warning threshold : 0.0032 mW / -24.95 dBm Signed-off-by: Ernesto Castellotti Reviewed-by: Przemek Kitszel Tested-by: Sunitha Mekala (A Contingent worker at Intel) Signed-off-by: Tony Nguyen Link: https://lore.kernel.org/r/20240301184806.2634508-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski

ixgbe: Convert ret val type from s32 to int

2024-02-06T21:17:14Z

Currently big amount of the functions returning standard error codes are of type s32. Convert them to regular ints as typdefs here are not necessary to return standard error codes. Fix incorrect args alignment in touched functions. Suggested-by: Jacob Keller Reviewed-by: Jacob Keller Reviewed-by: Simon Horman Signed-off-by: Jedrzej Jagielski Tested-by: Pucha Himasekhar Reddy (A Contingent worker at Intel) Signed-off-by: Tony Nguyen

ixgbe: Refactor overtemp event handling

2024-01-02T21:30:26Z

Currently ixgbe driver is notified of overheating events via internal IXGBE_ERR_OVERTEMP error code. Change the approach for handle_lasi() to use freshly introduced is_overtemp function parameter which set when such event occurs. Change check_overtemp() to bool and return true if overtemp event occurs. Reviewed-by: Przemek Kitszel Signed-off-by: Jedrzej Jagielski Reviewed-by: Jacob Keller Reviewed-by: Simon Horman Tested-by: Sunitha Mekala (A Contingent worker at Intel) Signed-off-by: Tony Nguyen

ixgbe: Check DDM existence in transceiver before access

2019-06-26T16:18:54Z

Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented. Currently, due to not checking this bit ixgbe fails trying to read SFP module's eeprom with the follow message: ethtool -m enP51p1s0f0 Cannot get Module EEPROM data: Input/output error Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data. This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers. Signed-off-by: "Mauro S. M. Rodrigues" Reviewed-by: Jesse Brandeburg Tested-by: Andrew Bowers Signed-off-by: Jeff Kirsher

ixgbe: register a mdiobus

2018-12-20T20:19:11Z

Most dsa devices expect a 'struct mii_bus' pointer to talk to switches via the MII interface. While this works for dsa devices, it will not work safely with Linux PHYs in all configurations since the firmware of the ixgbe device may be polling some PHY addresses in the background. Signed-off-by: Stephen Douthit Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Tested-by: Andrew Bowers Signed-off-by: Jeff Kirsher

net: intel: Cleanup the copyright/license headers

2018-04-27T18:00:04Z

After many years of having a ~30 line copyright and license header to our source files, we are finally able to reduce that to one line with the advent of the SPDX identifier. Also caught a few files missing the SPDX license identifier, so fixed them up. Signed-off-by: Jeff Kirsher Acked-by: Shannon Nelson Acked-by: Richard Cochran Tested-by: Andrew Bowers Signed-off-by: David S. Miller

intel: add SPDX identifiers to all the Intel drivers

2018-03-23T16:18:21Z

Add the SPDX identifiers to all the Intel wired LAN driver files, as outlined in Documentation/process/license-rules.rst. Signed-off-by: Jeff Kirsher Tested-by: Aaron Brown Signed-off-by: David S. Miller

ixgbe: correct CS4223/7 PHY identification

2017-05-31T11:48:19Z

Previous method was unreliable. Use a different register to differentiate between the SKUs. Signed-off-by: Emil Tantilov Tested-by: Andrew Bowers Signed-off-by: Jeff Kirsher

ixgbe: Remove unused firmware version functions and method

2017-01-03T21:03:38Z

The firmware version method and functions are not used anywhere, so remove them all. Signed-off-by: Mark Rustad Tested-by: Krishneil Singh Signed-off-by: Jeff Kirsher