kernel/drivers/net/ethernet/intel/igc/igc_base.c, branch linux-6.18.y

igc: return early when failing to read EECD register

2025-01-07T17:01:15Z

When booting with a dock connected, the igc driver may get stuck for ~40 seconds if PCIe link is lost during initialization. This happens because the driver access device after EECD register reads return all F's, indicating failed reads. Consequently, hw->hw_addr is set to NULL, which impacts subsequent rd32() reads. This leads to the driver hanging in igc_get_hw_semaphore_i225(), as the invalid hw->hw_addr prevents retrieving the expected value. To address this, a validation check and a corresponding return value catch is added for the EECD register read result. If all F's are returned, indicating PCIe link loss, the driver will return -ENXIO immediately. This avoids the 40-second hang and significantly improves boot time when using a dock with an igc NIC. Log before the patch: [ 0.911913] igc 0000:70:00.0: enabling device (0000 -> 0002) [ 0.912386] igc 0000:70:00.0: PTM enabled, 4ns granularity [ 1.571098] igc 0000:70:00.0 (unnamed net_device) (uninitialized): PCIe link lost, device now detached [ 43.449095] igc_get_hw_semaphore_i225: igc 0000:70:00.0 (unnamed net_device) (uninitialized): Driver can't access device - SMBI bit is set. [ 43.449186] igc 0000:70:00.0: probe with driver igc failed with error -13 [ 46.345701] igc 0000:70:00.0: enabling device (0000 -> 0002) [ 46.345777] igc 0000:70:00.0: PTM enabled, 4ns granularity Log after the patch: [ 1.031000] igc 0000:70:00.0: enabling device (0000 -> 0002) [ 1.032097] igc 0000:70:00.0: PTM enabled, 4ns granularity [ 1.642291] igc 0000:70:00.0 (unnamed net_device) (uninitialized): PCIe link lost, device now detached [ 5.480490] igc 0000:70:00.0: enabling device (0000 -> 0002) [ 5.480516] igc 0000:70:00.0: PTM enabled, 4ns granularity Fixes: ab4056126813 ("igc: Add NVM support") Cc: Chia-Lin Kao (AceLan) Signed-off-by: En-Wei Wu Reviewed-by: Vitaly Lifshits Tested-by: Mor Bar-Gabay Signed-off-by: Tony Nguyen

igc: field get conversion

2023-12-18T19:20:43Z

Refactor the igc driver to use FIELD_GET() for mask and shift reads, which reduces lines of code and adds clarity of intent. This code was generated by the following coccinelle/spatch script and then manually repaired in a later patch. @get@ constant shift,mask; type T; expression a; @@ -((T)((a) & mask) >> shift) +FIELD_GET(mask, a) and applied via: spatch --sp-file field_prep.cocci --in-place --dir \ drivers/net/ethernet/intel/ Cc: Julia Lawall Reviewed-by: Marcin Szycik Reviewed-by: Simon Horman Signed-off-by: Jesse Brandeburg Signed-off-by: Tony Nguyen

igc: remove I226 Qbv BaseTime restriction

2023-01-03T17:35:37Z

Remove the Qbv BaseTime restriction for I226 so that the BaseTime can be scheduled to the future time. A new register bit of Tx Qav Control (Bit-7: FutScdDis) was introduced to allow I226 scheduling future time as Qbv BaseTime and not having the Tx hang timeout issue. Besides, according to datasheet section 7.5.2.9.3.3, FutScdDis bit has to be configured first before the cycle time and base time. Indeed the FutScdDis bit is only active on re-configuration, thus we have to set the BASET_L to zero and then only set it to the desired value. Please also note that the Qbv configuration flow is moved around based on the Qbv programming guideline that is documented in the latest datasheet. Co-developed-by: Tan Tee Min Signed-off-by: Tan Tee Min Signed-off-by: Muhammad Husaini Zulkifli Tested-by: Naama Meir Signed-off-by: Tony Nguyen

igc: Remove unused phy_type enum

2022-05-10T21:02:40Z

Complete to commit 8e153faf5827 ("igc: Remove unused phy type") i225 parts have only one PHY. There is no point to use phy_type enum. Clean up the code accordingly, and get rid of the unused enum lines. Signed-off-by: Sasha Neftin Tested-by: Naama Meir Signed-off-by: Tony Nguyen

igc: Change Device Reset to Port Reset

2021-10-29T17:36:58Z

The _reset_hw_base method switched from port reset (CTRL[26]) to device reset (CTRL[29]) since the FW was receiving an interrupt on CTRL[29]. FW code was later modified to also receive an interrupt on CTRL[26]. Since certain HW values are not reset to default by CTRL[29], we go back to CTRL[26] for the HW reset, as it meets all current requirements. This reverts commit bb4265ec24c1 ("igc: Update the MAC reset flow"). Signed-off-by: Sasha Neftin Tested-by: Nechama Kraus Signed-off-by: Tony Nguyen

igc: Add new device ID

2021-10-29T16:51:26Z

Add new device ID for the next step of the silicon and reflect the I226_LMVP part. Signed-off-by: Sasha Neftin Tested-by: Nechama Kraus Signed-off-by: Tony Nguyen

igc: Remove media type checking on the PHY initialization

2021-10-29T16:51:21Z

i225 devices only have copper phy media type. There is no point in checking phy media type during the phy initialization. This patch cleans up a pointless check. Signed-off-by: Sasha Neftin Tested-by: Dvora Fuxbrumer Signed-off-by: Tony Nguyen

igc: Remove _I_PHY_ID checking

2021-07-20T23:11:36Z

i225 devices have only one PHY vendor. There is no point checking _I_PHY_ID during the link establishment and auto-negotiation process. This patch comes to clean up these pointless checkings. Signed-off-by: Sasha Neftin Tested-by: Dvora Fuxbrumer Signed-off-by: Tony Nguyen

igc: Add new device ID

2020-12-10T21:13:24Z

Add new device ID for the next step of the silicon and reflect the I226_K part. Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Tony Nguyen Signed-off-by: David S. Miller

igc: Add new device ID's

2020-09-28T21:42:45Z

Add new device ID's for the next step of the silicon and reflect i221 and i226 parts Signed-off-by: Sasha Neftin Tested-by: Aaron Brown Signed-off-by: Tony Nguyen