kernel/drivers/net/ethernet/intel/igb, branch linux-4.16.y

igb: Fix the transmission mode of queue 0 for Qav mode

2018-06-20T19:01:24Z

[ Upstream commit 2707df9773cd2cb8b0f35b8592431b301da9d352 ] When Qav mode is enabled, queue 0 should be kept on Stream Reservation mode. From the i210 datasheet, section 8.12.19: "Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to Qav." ("QueueMode 1b" represents the Stream Reservation mode) The solution is to give queue 0 the all the credits it might need, so it has priority over queue 1. A situation where this can happen is when cbs is "installed" only on queue 1, leaving queue 0 alone. For example: $ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0 $ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \ hicredit 30 sendslope -980000 idleslope 20000 offload 1 Signed-off-by: Vinicius Costa Gomes Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

igb: Clear TXSTMP when ptp_tx_work() is timeout

2018-01-24T20:27:48Z

Problem description: After ethernet cable connect and disconnect for several iterations on a device with i210, tx timestamp will stop being put into the socket. Steps to reproduce: 1. Setup a device with i210 and wire it to a 802.1AS capable switch ( Extreme Networks Summit x440 is used in our case) 2. Have the gptp daemon running on the device and make sure it is synced with the switch 3. Have the switch disable and enable the port, wait for the device gets resynced with the switch 4. Iterates step 3 until the device is not albe to get resynced 5. Review the log in dmesg and you will see warning message "igb : clearing Tx timestamp hang" Root cause: If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK DOWN event will be processed before ptp_tx_work(), which may cause timeout in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit timestamp valid bit) is not cleared, causing no new timestamp loaded to TXSTMP register. Consequently therefore, no new interrupt is triggerred by TSICR.TXTS bit and no more Tx timestamp send to the socket. Signed-off-by: Daniel Hua Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: Delete an error message for a failed memory allocation in igb_enable_sriov()

2018-01-24T20:27:48Z

Omit an extra message for a memory allocation failure in this function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: Free IRQs when device is hotplugged

2018-01-24T20:27:48Z

Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon hotplugging my kernel would immediately crash due to igb: [ 680.825801] kernel BUG at drivers/pci/msi.c:352! [ 680.828388] invalid opcode: 0000 [#1] SMP [ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb] [ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6 [ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017 [ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0 [ 680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286 [ 680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c [ 680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178 [ 680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00 [ 680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298 [ 680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000 [ 680.836332] FS: 0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000 [ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0 [ 680.837954] Call Trace: [ 680.838853] pci_disable_msix+0xce/0xf0 [ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb] [ 680.840278] igb_remove+0x9d/0x110 [igb] [ 680.840764] pci_device_remove+0x36/0xb0 [ 680.841279] device_release_driver_internal+0x157/0x220 [ 680.841739] pci_stop_bus_device+0x7d/0xa0 [ 680.842255] pci_stop_bus_device+0x2b/0xa0 [ 680.842722] pci_stop_bus_device+0x3d/0xa0 [ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20 [ 680.843627] trim_stale_devices+0xf3/0x140 [ 680.844086] trim_stale_devices+0x94/0x140 [ 680.844532] trim_stale_devices+0xa6/0x140 [ 680.845031] ? get_slot_status+0x90/0xc0 [ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140 [ 680.846021] acpiphp_hotplug_notify+0x175/0x200 [ 680.846581] ? free_bridge+0x100/0x100 [ 680.847113] acpi_device_hotplug+0x8a/0x490 [ 680.847535] acpi_hotplug_work_fn+0x1a/0x30 [ 680.848076] process_one_work+0x182/0x3a0 [ 680.848543] worker_thread+0x2e/0x380 [ 680.848963] ? process_one_work+0x3a0/0x3a0 [ 680.849373] kthread+0x111/0x130 [ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50 [ 680.850188] ret_from_fork+0x1f/0x30 [ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b [ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0 As it turns out, normally the freeing of IRQs that would fix this is called inside of the scope of __igb_close(). However, since the device is already gone by the point we try to unregister the netdevice from the driver due to a hotplug we end up seeing that the netif isn't present and thus, forget to free any of the device IRQs. So: make sure that if we're in the process of dismantling the netdev, we always allow __igb_close() to be called so that IRQs may be freed normally. Additionally, only allow igb_close() to be called from __igb_close() if it hasn't already been called for the given adapter. Signed-off-by: Lyude Paul Fixes: 9474933caf21 ("igb: close/suspend race in netif_device_detach") Cc: Todd Fujinaka Cc: Stephen Hemminger Cc: stable@vger.kernel.org Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: Clarify idleslope config constraints

2018-01-24T20:27:48Z

By design, the idleslope increments are restricted to 16.384kbps steps. Add a comment to igb_main.c making that explicit and add one example that illustrates the impact of that. Signed-off-by: Jesus Sanchez-Palencia Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: add function to get maximum RSS queues

2018-01-24T20:27:48Z

This patch adds a new function igb_get_max_rss_queues() to get maximum RSS queues, this will reduce duplicate code and facilitate future maintenance. Signed-off-by: Zhang Shengju Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: Allow to remove administratively set MAC on VFs

2018-01-24T20:27:48Z

Before libvirt modifies the MAC address and vlan tag for an SRIOV VF for use by a virtual machine (either using vfio device assignment or macvtap passthru mode), it saves the current MAC address and vlan tag so that it can reset them to their original value when the guest is done. Libvirt can't leave the VF MAC set to the value used by the now-defunct guest since it may be started again later using a different VF, but it certainly shouldn't just pick any random value, either. So it saves the state of everything prior to using the VF, and resets it to that. The igb driver initializes the MAC addresses of all VFs to 00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK netlink message, also visible in the list of VFs in the output of "ip link show"). But when libvirt attempts to restore the MAC address back to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel responds with "Invalid argument". Forbidding a reset back to the original value leaves the VF MAC at the value set for the now-defunct virtual machine. Especially on a system with NetworkManager enabled, this has very bad consequences, since NetworkManager forces all interfacess to be IFF_UP all the time - if the same virtual machine is restarted using a different VF (or even on a different host), there will be multiple interfaces watching for traffic with the same MAC address. To allow libvirt to revert to the original state, we need a way to remove the administrative set MAC on a VF, to allow normal host operation again, and to reset/overwrite the VF MAC via VF netdev. This patch implements the outlined scenario by allowing to set the VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF. igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0, so it's possible to reset the VF MAC back to the original value via the VF netdev. Note: Recent patches to libvirt allow for a workaround if the NIC isn't capable of resetting the administrative MAC back to all 0, but in theory the NIC should allow resetting the MAC in the first place. Signed-off-by: Corinna Vinschen Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

igb: Use smp_rmb rather than read_barrier_depends

2017-11-22T07:47:24Z

The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igb as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Cc: stable Signed-off-by: Brian King Acked-by: Jesse Brandeburg Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

2017-11-15T19:56:19Z

Pull networking updates from David Miller: "Highlights: 1) Maintain the TCP retransmit queue using an rbtree, with 1GB windows at 100Gb this really has become necessary. From Eric Dumazet. 2) Multi-program support for cgroup+bpf, from Alexei Starovoitov. 3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew Lunn. 4) Add meter action support to openvswitch, from Andy Zhou. 5) Add a data meta pointer for BPF accessible packets, from Daniel Borkmann. 6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet. 7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli. 8) More work to move the RTNL mutex down, from Florian Westphal. 9) Add 'bpftool' utility, to help with bpf program introspection. From Jakub Kicinski. 10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper Dangaard Brouer. 11) Support 'blocks' of transformations in the packet scheduler which can span multiple network devices, from Jiri Pirko. 12) TC flower offload support in cxgb4, from Kumar Sanghvi. 13) Priority based stream scheduler for SCTP, from Marcelo Ricardo Leitner. 14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg. 15) Add RED qdisc offloadability, and use it in mlxsw driver. From Nogah Frankel. 16) eBPF based device controller for cgroup v2, from Roman Gushchin. 17) Add some fundamental tracepoints for TCP, from Song Liu. 18) Remove garbage collection from ipv6 route layer, this is a significant accomplishment. From Wei Wang. 19) Add multicast route offload support to mlxsw, from Yotam Gigi" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits) tcp: highest_sack fix geneve: fix fill_info when link down bpf: fix lockdep splat net: cdc_ncm: GetNtbFormat endian fix openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start netem: remove unnecessary 64 bit modulus netem: use 64 bit divide by rate tcp: Namespace-ify sysctl_tcp_default_congestion_control net: Protect iterations over net::fib_notifier_ops in fib_seq_sum() ipv6: set all.accept_dad to 0 by default uapi: fix linux/tls.h userspace compilation error usbnet: ipheth: prevent TX queue timeouts when device not ready vhost_net: conditionally enable tx polling uapi: fix linux/rxrpc.h userspace compilation errors net: stmmac: fix LPI transitioning for dwmac4 atm: horizon: Fix irq release error net-sysfs: trigger netlink notification on ifalias change via sysfs openvswitch: Using kfree_rcu() to simplify the code openvswitch: Make local function ovs_nsh_key_attr_size() static openvswitch: Fix return value check in ovs_meter_cmd_features() ...

net_sch: cbs: Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS

2017-11-08T03:23:38Z

Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS to match the new convention.. Signed-off-by: Nogah Frankel Signed-off-by: Jiri Pirko Reviewed-by: Simon Horman Acked-by: Vinicius Costa Gomes Signed-off-by: David S. Miller