kernel/drivers/net/ethernet/intel/e1000e/mac.c, branch linux-4.3.y

e1000e: Bump the version to 3.2.5

2015-06-03T11:13:39Z

Bump the version to reflect the driver changes and bug fixes for i219. Also update the copyright, while we are at it. Signed-off-by: Yanir Lubetkin Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: remove unnecessary break after return

2014-07-21T04:30:18Z

Signed-off-by: Fabian Frederick Signed-off-by: David S. Miller

e1000e: Failure to write SHRA turns on PROMISC mode

2014-05-27T06:53:11Z

Previously, the check to turn on promiscuous mode only took into account the total number of SHared Receive Address (SHRA) registers and if the request was for a register within that range. It is possible that the Management Engine might have locked a number of SHRA and not allowed a new address to be written to the requested register. Add a function to determine the number of unlocked SHRA registers. Then determine if the number of registers available is sufficient for our needs, if not then return -ENOMEM so that UNICAST PROMISC mode is activated. Since the method by which ME claims SHRA registers is non-deterministic, also add a return value to the function attempting to write an address to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error will be passed up the function chain and allow the driver to also set UNICAST PROMISC when this happens. Cc: Vlad Yasevich Signed-off-by: Dave Ertman Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: Cleanup - Update GPL header and Copyright

2014-03-08T05:55:27Z

This patch is to update the GPL header by removing the portion that refers to the Free Software Foundation address. Change the copyright date for 2014. Reformat the header comments to conform to kernel networking coding norms Signed-off-by: Dave Ertman Tested-by: Jeff Pieper Signed-off-by: Jeff Kirsher

e1000e: fix LED blink logic for designs with LEDs driven by cathode

2013-03-28T06:32:06Z

When the LEDs are driven by cathode, the bit logic is reversed. Use the LED Invert bit to invert the logic. Cleanup use of a magic number and change the for loop increment to reduce the number of shifts. Signed-off-by: Bruce Allan Tested-by: Jeff Pieper Signed-off-by: Jeff Kirsher

e1000e: cleanup USLEEP_RANGE checkpatch checks

2013-03-08T09:28:59Z

Resolve strict checkpatch USLEEP_RANGE checks by converting delays and sleeps as described in ./Documentation/timers/timers-howto.txt. Three other violations of the text have also been fixed. CHECK:USLEEP_RANGE: usleep_range is preferred over udelay; see Documentation/timers/timers-howto.txt Signed-off-by: Bruce Allan Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: use generic IEEE MII definitions

2013-02-01T06:34:59Z

For standard IEEE MII-compatible transceivers, the kernel has generic register and bit definitions. Use those instead of redundant local defines. Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000) when it is not necessary (i.e. when it is bitwise OR'ed with another value). Some whitespace issues in the surrounding context of the above changes are also cleaned up. Signed-off-by: Bruce Allan Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: resolve -Wunused-parameter compile warnings

2013-02-01T06:28:39Z

Remove the unused parameter when possible, otherwise use __always_unused attribute. Signed-off-by: Bruce Allan Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: cleanup some whitespace and indentation issues

2013-02-01T06:16:11Z

Signed-off-by: Bruce Allan Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher

e1000e: cleanup: do not assign a variable a value when not necessary

2013-01-27T10:15:48Z

Static analysis with cppcheck has shown a few instances of a variable being reassigned a value before the old one has been used. None of these ever require the old value to be used so remove the old values. Signed-off-by: Bruce Allan Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher