kernel/drivers/net/ethernet/broadcom/genet, branch linux-4.3.y

net: bcmgenet: Software reset EPHY after power on

2015-12-09T19:34:07Z

[ Upstream commit 5dbebbb44a6ad94aab2cd1a46f7676f255403f64 ] The EPHY on GENET v1->v3 is extremely finicky, and will show occasional failures based on the timing and reset sequence, ranging from duplicate packets, to extremely high latencies. Perform an additional software reset, and re-configuration to make sure it is in a consistent and working state. Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: bcmgenet: Fix early link interrupt enabling

2015-10-19T06:07:12Z

Link interrupts are enabled in init_umac(), which is too early for us to process them since we do not yet have a valid PHY device pointer. On BCM7425 chips for instance, we will crash calling phy_mac_interrupt() because phydev is NULL. Fix this by moving the link interrupts enabling in bcmgenet_netif_start(), under a specific function: bcmgenet_link_intr_enable() and while at it, update the comments surrounding the code. Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: bcmgenet: Fix module autoload for OF platform driver

2015-09-21T23:08:21Z

This platform driver has a OF device ID table but the OF module alias information is not created so module autoloading won't work. Signed-off-by: Luis de Bethencourt Acked-by: Florian Fainelli Signed-off-by: David S. Miller

phy: fixed_phy: Add gpio to determine link up/down.

2015-08-31T21:48:02Z

An SFP module may have a link up/down status pin which can be connection to a GPIO line of the host. Add support for reading such an GPIO in the fixed_phy driver. Signed-off-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2015-08-28T04:45:31Z

net: bcmgenet: fix uncleaned dma flags

2015-08-24T06:00:41Z

Clean the dma flags of multiq ring buffer int the interface stop process. This patch fixes that the genet is not running while the interface is re-enabled. $ ifup eth0 - running after booting $ ifdown eth0 $ ifup eth0 - not running and occur tx_timeout The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag only. If the genet has multiq, the dma register is not cleaned. and bcmgenet_init_dma() is not done correctly. in case GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running bcmgenet_dma_disable(). Signed-off-by: Jaedon Shin Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: bcmgenet: Avoid sleeping in bcmgenet_timeout

2015-08-24T05:59:33Z

bcmgenet_timeout() executes in atomic context, yet we will invoke napi_disable() which does sleep. Looking back at the changes, disabling TX napi and re-enabling it is completely useless, since we reclaim all TX buffers and re-enable interrupts, and wake up the TX queues. Fixes: 13ea657806cf ("net: bcmgenet: improve TX timeout") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: bcmgenet: Add netconsole support

2015-07-31T22:45:36Z

Implement a poll controller for netconsole which invokes both of our interrupt handlers for the different RX/TX queues. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: bcmgenet: Register link_update callback for all MoCA PHYs

2015-07-27T03:53:56Z

Commit 8d88c6ebb34c ("net: bcmgenet: enable MoCA link state change detection") added a fixed PHY link_update callback for MoCA PHYs when registered using platform_data exclusively, this change is also applicable to systems using Device Tree as their primary configuration interface. In order for this to work, move the link_update assignment into bcmgenet_moca_phy_setup() where we know for sure that we are running on a MoCA GENET instance, and do not override phydev->link since this is: - properly taken care of by the PHY library by getting the link UP/DOWN interrupts - this now runs everytime we call bcmgenet_open(), so we need to preserve whatever we detected before we went administratively DOWN and then UP - we need to make sure that MoCA PHYs start with a link DOWN during probe in order to force a link transition to occur To avoid a forward declaration, move bcmgenet_fixed_phy_link_update() above its caller. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller

net: bcmgenet: Remove checks on clock handles

2015-07-27T00:21:56Z

Instead of multiplying the number of checks for IS_ERR(priv->clk), simply NULLify the 'struct clk' pointer which is something the Linux common clock framework perfectly deals with and does early return for each and every single clk_* API functions. Having every single function check for !IS_ERR(priv->clk) is both redundant and error prone, as it turns out, we were doing it for the main GENET clock: priv->clk, but not for the Wake-on-LAN or EEE clock, so let's just be consistent here. Signed-off-by: Florian Fainelli Acked-by: Petri Gynther Signed-off-by: David S. Miller