kernel/drivers/net/dsa, branch linux-5.9.y

net: mscc: ocelot: fix dropping of unknown IPv4 multicast on Seville

2020-12-21T12:28:15Z

[ Upstream commit edd2410b165e2ef00b2264ae362edf7441ca929c ] The current assumption is that the felix DSA driver has flooding knobs per traffic class, while ocelot switchdev has a single flooding knob. This was correct for felix VSC9959 and ocelot VSC7514, but with the introduction of seville VSC9953, we see a switch driven by felix.c which has a single flooding knob. So it is clear that we must do what should have been done from the beginning, which is not to overwrite the configuration done by ocelot.c in felix, but instead to teach the common ocelot library about the differences in our switches, and set up the flooding PGIDs centrally. The effect that the bogus iteration through FELIX_NUM_TC has upon seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will actually overwrite ANA_FLOODING_IPMC when attempting to write ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING. And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D: MC6_DATA = 61, MC6_CTRL = 61, MC4_DATA = 60, MC4_CTRL = 0. Because MC4_CTRL is zero, this means that IPv4 multicast control packets are not flooded, but dropped. An invalid configuration, and this is how the issue was actually spotted. Reported-by: Eldar Gasanov Reported-by: Maxim Kochetkov Tested-by: Eldar Gasanov Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch") Fixes: 3c7b51bd39b2 ("net: dsa: felix: allow flooding for all traffic classes") Signed-off-by: Vladimir Oltean Reviewed-by: Alexandre Belloni Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset

2020-12-02T07:51:51Z

[ Upstream commit a3dcb3e7e70c72a68a79b30fc3a3adad5612731c ] When the switch is hardware reset, it reads the contents of the EEPROM. This can contain instructions for programming values into registers and to perform waits between such programming. Reading the EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits after deasserting the reset GPIO. So poll the EEPROM done bit to ensure it is complete. Signed-off-by: Andrew Lunn Signed-off-by: Ruslan Sushko Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: lantiq: Wait for the GPHY firmware to be ready

2020-11-24T12:38:48Z

[ Upstream commit 2a1828e378c1b5ba1ff283ed8f8c5cc37bb391dc ] A user reports (slightly shortened from the original message): libphy: lantiq,xrx200-mdio: probed mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing. gswip 1e108000.switch lan: no phy at 2 gswip 1e108000.switch lan: failed to connect to port 2: -19 lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy This is a single-port board using the internal Fast Ethernet PHY. The user reports that switching to PHY scanning instead of configuring the PHY within device-tree works around this issue. The documentation for the standalone variant of the PHY11G (which is probably very similar to what is used inside the xRX200 SoCs but having the firmware burnt onto that standalone chip in the factory) states that the PHY needs 300ms to be ready for MDIO communication after releasing the reset. Add a 300ms delay after initializing all GPHYs to ensure that the GPHY firmware had enough time to initialize and to appear on the MDIO bus. Unfortunately there is no (known) documentation on what the minimum time to wait after releasing the reset on an internal PHY so play safe and take the one for the external variant. Only wait after the last GPHY firmware is loaded to not slow down the initialization too much ( xRX200 has two GPHYs but newer SoCs have at least three GPHYs). Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Reviewed-by: Andrew Lunn Signed-off-by: Martin Blumenstingl Acked-by: Hauke Mehrtens Reviewed-by: Florian Fainelli Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: Avoid VTU corruption on 6097

2020-11-24T12:38:47Z

[ Upstream commit 92307069a96c07d9b6e74b96b79390e7cd7d2111 ] As soon as you add the second port to a VLAN, all other port membership configuration is overwritten with zeroes. The HW interprets this as all ports being "unmodified members" of the VLAN. In the simple case when all ports belong to the same VLAN, switching will still work. But using multiple VLANs or trying to set multiple ports as tagged members will not work. On the 6352, doing a VTU GetNext op, followed by an STU GetNext op will leave you with both the member- and state- data in the VTU/STU data registers. But on the 6097 (which uses the same implementation), the STU GetNext will override the information gathered from the VTU GetNext. Separate the two stages, parsing the result of the VTU GetNext before doing the STU GetNext. We opt to update the existing implementation for all applicable chips, as opposed to creating a separate callback for 6097, because although the previous implementation did work for (at least) 6352, the datasheet does not mention the masking behavior. Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext") Signed-off-by: Tobias Waldekranz Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: qca8k: Fix port MTU setting

2020-11-10T11:38:58Z

[ Upstream commit 99cab7107d914a71c57f5a4e6d34292425fbbb61 ] The qca8k only supports a switch-wide MTU setting, and the code to take the max of all ports was only looking at the port currently being set. Fix to examine all ports. Reported-by: DENG Qingfang Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks") Signed-off-by: Jonathan McDowell Reviewed-by: Andrew Lunn Link: https://lore.kernel.org/r/20201030183315.GA6736@earth.li Signed-off-by: Jakub Kicinski Signed-off-by: Greg Kroah-Hartman

net: dsa: seville: the packet buffer is 2 megabits, not megabytes

2020-10-29T09:11:59Z

[ Upstream commit a15a6afb3bf9388eb83a4b876d3453f305fba909 ] The VSC9953 Seville switch has 2 megabits of buffer split into 4360 words of 60 bytes each. 2048 * 1024 is 2 megabytes instead of 2 megabits. 2 megabits is (2048 / 8) * 1024 = 256 * 1024. Signed-off-by: Maxim Kochetkov Reviewed-by: Vladimir Oltean Fixes: a63ed92d217f ("net: dsa: seville: fix buffer size of the queue system") Link: https://lore.kernel.org/r/20201019050625.21533-1-fido_max@inbox.ru Signed-off-by: Jakub Kicinski Signed-off-by: Sasha Levin

net: dsa: rtl8366rb: Support all 4096 VLANs

2020-10-29T09:11:25Z

[ Upstream commit a7920efdd86d8a0d74402dbc80ead03b023294ba ] There is an off-by-one error in rtl8366rb_is_vlan_valid() making VLANs 0..4094 valid while it should be 1..4095. Fix it. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: rtl8366: Skip PVID setting if not requested

2020-10-29T09:11:24Z

[ Upstream commit 3dfe8dde093a07e82fa472c0f8c29a7f6a2006a5 ] We go to lengths to determine whether the PVID should be set for this port or not, and then fail to take it into account. Fix this oversight. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: rtl8366: Refactor VLAN/PVID init

2020-10-29T09:11:24Z

[ Upstream commit 7e1301ed1881447d2a25f9c6423738c33cbca133 ] The VLANs and PVIDs on the RTL8366 utilizes a "member configuration" (MC) which is largely unexplained in the code. This set-up requires a special ordering: rtl8366_set_pvid() must be called first, followed by rtl8366_set_vlan(), else the MC will not be properly allocated. Relax this by factoring out the code obtaining an MC and reuse the helper in both rtl8366_set_pvid() and rtl8366_set_vlan() so we remove this strict ordering requirement. In the process, add some better comments and debug prints so people who read the code understand what is going on. Reviewed-by: Florian Fainelli Signed-off-by: Linus Walleij Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: rtl8366: Check validity of passed VLANs

2020-10-29T09:11:23Z

[ Upstream commit 6641a2c42b0a307b7638d10e5d4b90debc61389d ] The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid VLANs tossed at it, especially VLAN0, something the hardware and driver cannot handle. Check validity and bail out like we do in the other callbacks. Reviewed-by: Florian Fainelli Signed-off-by: Linus Walleij Signed-off-by: David S. Miller Signed-off-by: Sasha Levin