kernel/drivers/net/dsa, branch linux-5.1.y

net: dsa: mv88e6xxx: wait after reset deactivation

2019-07-28T06:28:27Z

[ Upstream commit 7b75e49de424ceb53d13e60f35d0a73765626fda ] Add a 1ms delay after reset deactivation. Otherwise the chip returns bogus ID value. This is observed with 88E6390 (Peridot) chip. Signed-off-by: Baruch Siach Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()

2019-07-14T06:09:46Z

[ Upstream commit 48620e341659f6e4b978ec229f6944dabe6df709 ] The comment is correct, but the code ends up moving the bits four places too far, into the VTUOp field. Fixes: 11ea809f1a74 (net: dsa: mv88e6xxx: support 256 databases) Signed-off-by: Rasmus Villemoes Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: mv88e6xxx: avoid error message on remove from VLAN 0

2019-06-25T03:34:50Z

[ Upstream commit 62394708f3e01c9f2be6be74eb6305bae1ed924f ] When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error message is logged: failed to kill vid 0081/0 for device eth_cu_1000_4 This is caused by call from __vlan_vid_del() with vin set to zero, over call chain this results into _mv88e6xxx_port_vlan_del() called with vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL. On symmetric path moving port up, call goes through mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan() that returns -EOPNOTSUPP for zero vid. This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for zero vid, then this error code is explicitly cleared in dsa_slave_vlan_rx_kill_vid() and error message is no longer logged. Signed-off-by: Nikita Yushchenko Reviewed-by: Vivien Didelot Signed-off-by: David S. Miller Signed-off-by: Sasha Levin

net: dsa: microchip: Don't try to read stats for unused ports

2019-06-22T06:09:06Z

[ Upstream commit 6bb9e376c2a4cc5120c3bf5fd3048b9a0a6ec1f8 ] If some of the switch ports were not listed in the device tree, due to being unused, the ksz_mib_read_work function ended up accessing a NULL dp->slave pointer and causing an oops. Skip checking statistics for any unused ports. Fixes: 7c6ff470aa867f53 ("net: dsa: microchip: add MIB counter reading support") Signed-off-by: Robert Hancock Reviewed-by: Vivien Didelot Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: rtl8366: Fix up VLAN filtering

2019-06-22T06:09:04Z

[ Upstream commit 760c80b70bed2cd01630e8595d1bbde910339f31 ] We get this regression when using RTL8366RB as part of a bridge with OpenWrt: WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291 switchdev_port_attr_set_now+0x80/0xa4 lan0: Commit of attribute (id=7) failed. (...) realtek-smi switch lan0: failed to initialize vlan filtering on this port This is because it is trying to disable VLAN filtering on VLAN0, as we have forgot to add 1 to the port number to get the right VLAN in rtl8366_vlan_filtering(): when we initialize the VLAN we associate VLAN1 with port 0, VLAN2 with port 1 etc, so we need to add 1 to the port offset. Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT

2019-06-04T05:59:41Z

[ Upstream commit 84b3fd1fc9592d431e23b077e692fa4e3fd0f086 ] Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends up in bits 47:32 of the return value, instead of bits 31:16 as they should. Fixes: 6e46e2d821bb ("net: dsa: mv88e6xxx: Fix u64 statistics") Signed-off-by: Rasmus Villemoes Reviewed-by: Vivien Didelot Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc

2019-04-30T15:02:37Z

The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc(). We can't pass unclamped values to test_bit() or it results in an out of bounds access beyond the end of the bitmap. Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller

net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmode

2019-03-28T04:53:50Z

This patches fixes few issues in mv88e6390x_port_set_cmode(). 1. When entering the function the old cmode may be 0, in this case mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail out and have no chance to set a new mode. Therefore deal properly with -ENODEV. 2. Once we have disabled power and irq, let's set the cached cmode to 0. This reflects the actual status and is cleaner if we bail out with an error in the following function calls. 3. The cached cmode is used by mv88e6390x_serdes_get_lane(), mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable(). Currently we set the cached mode to the new one at the very end of the function only, means until then we use the old one what may be wrong. 4. When calling mv88e6390_serdes_irq_enable() we use the lane value belonging to the old cmode. Get the lane belonging to the new cmode before calling this function. It's hard to provide a good "Fixes" tag because quite a few smaller changes have been done to the code in question recently. Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X") Signed-off-by: Heiner Kallweit Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller

net: dsa: qca8k: extend slave-bus implementations

2019-03-26T17:47:10Z

This patch implements accessors for the QCA8337 MDIO access through the MDIO_MASTER register, which makes it possible to access the PHYs on slave-bus through the switch. In cases where the switch ports are already mapped via external "phy-phandles", the internal mdio-bus is disabled in order to prevent a duplicated discovery and enumeration of the same PHYs. Don't use mixed external and internal mdio-bus configurations, as this is not supported by the hardware. Signed-off-by: Christian Lamparter Signed-off-by: David S. Miller

net: dsa: qca8k: remove leftover phy accessors

2019-03-26T17:47:10Z

This belated patch implements Andrew Lunn's request of "remove the phy_read() and phy_write() functions." While seemingly harmless, this causes the switch's user port PHYs to get registered twice. This is because the DSA subsystem will create a slave mdio-bus not knowing that the qca8k_phy_(read|write) accessors operate on the external mdio-bus. So the same "bus" gets effectively duplicated. Cc: stable@vger.kernel.org Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter Signed-off-by: David S. Miller