kernel/drivers/net/can/spi, branch linux-rolling-stable

can: hi311x: hi3110_open(): add check for hi3110_power_enable() return value

2026-03-19T15:14:53Z

[ Upstream commit 47bba09b14fa21712398febf36cb14fd4fc3bded ] In hi3110_open(), the return value of hi3110_power_enable() is not checked. If power enable fails, the device may not function correctly, while the driver still returns success. Add a check for the return value and propagate the error accordingly. Signed-off-by: Wenyuan Li <2063309626@qq.com> Link: https://patch.msgid.link/tencent_B5E2E7528BB28AA8A2A56E16C49BD58B8B07@qq.com Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver") [mkl: adjust subject, commit message and jump label] Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: mcp251x: fix deadlock in error path of mcp251x_open

2026-03-12T11:09:47Z

[ Upstream commit ab3f894de216f4a62adc3b57e9191888cbf26885 ] The mcp251x_open() function call free_irq() in its error path with the mpc_lock mutex held. But if an interrupt already occurred the interrupt handler will be waiting for the mpc_lock and free_irq() will deadlock waiting for the handler to finish. This issue is similar to the one fixed in commit 7dd9c26bd6cf ("can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open") but for the error path. To solve this issue move the call to free_irq() after the lock is released. Setting `priv->force_quit = 1` beforehand ensure that the IRQ handler will exit right away once it acquired the lock. Signed-off-by: Alban Bedel Link: https://patch.msgid.link/20260209144706.2261954-1-alban.bedel@lht.dlh.de Fixes: bf66f3736a94 ("can: mcp251x: Move to threaded interrupts instead of workqueues.") Signed-off-by: Marc Kleine-Budde Signed-off-by: Sasha Levin

can: mcp251xfd: add gpio functionality

2025-11-12T18:30:33Z

The mcp251xfd devices allow two pins to be configured as gpio. Add this functionality to driver. Acked-by: Bartosz Golaszewski Signed-off-by: Gregor Herburger Tested-by: Viken Dadhaniya Signed-off-by: Viken Dadhaniya Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20251001091006.4003841-6-viken.dadhaniya@oss.qualcomm.com Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: only configure PIN1 when rx_int is set

2025-11-12T18:30:32Z

When rx_int is used th mcp251xfd_chip_rx_int_enable and mcp251xfd_chip_rx_int_disable function configure both PIN0 and PIN1. To prepare the support of the GPIOS only configure PIN1 with regmap_update_bits. This way PIN0 can be used as GPIO while PIN1 is used as rx_int interrupt. Signed-off-by: Gregor Herburger Tested-by: Viken Dadhaniya Signed-off-by: Viken Dadhaniya Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20251001091006.4003841-5-viken.dadhaniya@oss.qualcomm.com Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: add workaround for errata 5

2025-11-12T18:30:07Z

According to Errata DS80000789E 5 writing IOCON register using one SPI write command clears LAT0/LAT1. Errata Fix/Work Around suggests to write registers with single byte write instructions. However, it seems that every write to the second byte causes the overwrite of LAT0/LAT1. Never write byte 2 of IOCON register to avoid clearing of LAT0/LAT1. Signed-off-by: Gregor Herburger Tested-by: Viken Dadhaniya Signed-off-by: Viken Dadhaniya Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20251001091006.4003841-4-viken.dadhaniya@oss.qualcomm.com [mkl: add missing MCP251XFD_REG_IOCON_GPIO_MASK] Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: utilize gather_write function for all non-CRC writes

2025-11-12T08:36:59Z

This is a preparation patch to add errata workaround for non crc writes. Currently for non-crc writes to the chip can go through the .gather_write, .write or the reg_update_bits callback. To allow the addition of the errata fix at a single location use mcp251xfd_regmap_nocrc_gather_write for all non-CRC write instructions, similar to the crc regmap. Signed-off-by: Gregor Herburger Tested-by: Viken Dadhaniya Signed-off-by: Viken Dadhaniya Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20251001091006.4003841-3-viken.dadhaniya@oss.qualcomm.com Signed-off-by: Marc Kleine-Budde

can: mcp251xfd: move chip sleep mode into runtime pm

2025-11-12T08:36:59Z

This is a preparation patch to add GPIO support. Up to now, the Vdd regulator and the clocks have been managed by Runtime-PM (on systems without CONFIG_PM these remain permanently switched on). During the mcp251xfd_open() callback the mcp251xfd is powered, soft-reset and configured. In mcp251xfd_stop() the chip is shut down again. To support the on-chip GPIOs, the chip must be supplied with power while GPIOs are being requested, even if the networking interface is down. To support this, move the functions mcp251xfd_chip_softreset() and mcp251xfd_chip_clock_init() from mcp251xfd_chip_start() to mcp251xfd_runtime_resume(). Instead of setting the controller to sleep mode in mcp251xfd_chip_stop(), bring it into configuration mode. This way it doesn't take part in bus activity and doesn't enter sleep mode. Signed-off-by: Gregor Herburger Tested-by: Viken Dadhaniya Signed-off-by: Viken Dadhaniya Reviewed-by: Manivannan Sadhasivam Link: https://patch.msgid.link/20251001091006.4003841-2-viken.dadhaniya@oss.qualcomm.com Signed-off-by: Marc Kleine-Budde

can: mcp251x: mcp251x_can_probe(): use dev_err_probe()

2025-10-31T12:17:46Z

The currently used combination of dev_err() plus return leaves a loud error in dmesg even when the error is a deferred probe which gets resolved later. For example a supply that has not been probed yet. Use dev_err_probe() to improve the handling/display of errors. Signed-off-by: Maud Spierings Link: https://patch.msgid.link/20251030-mcp_err-v1-1-eecf737823b7@gocontroll.com Signed-off-by: Marc Kleine-Budde

can: convert generic HW timestamp ioctl to ndo_hwtstamp callbacks

2025-10-31T12:12:18Z

Can has generic implementation of ndo_eth_ioctl which implements only HW timestamping commands. Implement generic ndo_hwtstamp callbacks and use it in drivers instead of generic ioctl interface. Signed-off-by: Vadim Fedorenko Reviewed-by: Kory Maincent Reviewed-by: Vincent Mailhol Link: https://patch.msgid.link/20251029231620.1135640-2-vadim.fedorenko@linux.dev Signed-off-by: Marc Kleine-Budde

can: treewide: remove can_change_mtu()

2025-10-17T07:57:13Z

can_change_mtu() became obsolete by commit 23049938605b ("can: populate the minimum and maximum MTU values"). Now that net_device->min_mtu and net_device->max_mtu are populated, all the checks are already done by dev_validate_mtu() in net/core/dev.c. Remove the net_device_ops->ndo_change_mtu() callback of all the physical interfaces, then remove can_change_mtu(). Only keep the vcan_change_mtu() and vxcan_change_mtu() because the virtual interfaces use their own different MTU logic. The only functional change this patch introduces is that now the user will be able to change the MTU even if the interface is up. This does not matter for Classical CAN and CAN FD because their MTU range is composed of only one value, respectively CAN_MTU and CANFD_MTU. For the upcoming CAN XL, the MTU will be configurable within the CANXL_MIN_MTU to CANXL_MAX_MTU range at any time, even if the interface is up. This is consistent with the other net protocols and does not contradict ISO 11898-1:2024 as having a modifiable MTU is a kernel extension. Signed-off-by: Vincent Mailhol Link: https://patch.msgid.link/20251003-remove-can_change_mtu-v1-1-337f8bc21181@kernel.org Signed-off-by: Marc Kleine-Budde