kernel/drivers/mfd/madera-core.c, branch linux-6.9.y

mfd: madera: Include correct gpio API

2022-12-07T13:28:07Z

The driver is using gpiod API and therefore should include linux/gpio/consumer.h, not linux/gpio.h. Also, the driver does not use any of the APIs from of_gpio.h, so we should not be including it. Signed-off-by: Dmitry Torokhov Signed-off-by: Lee Jones Link: https://lore.kernel.org/r/20220926054421.1546436-2-dmitry.torokhov@gmail.com

mfd: madera: Add special errata reset handling for cs47l15

2020-11-19T08:34:22Z

An errata exists for cs47l15 where the reset must be handled differently and removed before DCVDD is applied. A soft reset is used for situations where a reset is required to reset state. This does however, make this part unsuitable for DCVDD supplies with a rise time greater than 2mS. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Add reset as part of resume

2020-11-19T08:34:22Z

The DCVDD supply does not always power down when the CODEC enters suspend, for example shared regulators or always-on regulators. In these cases if a register is written back to the default value whilst the CODEC is in suspend that register will retain the previous value. As DCVDD never powered down, the register retains its old value and as the cache sync only synchronises registers that differ from the default the new value is never written out. Ensure the registers are in the expected state after suspend by always resetting the CODEC on resume. This also has the benefit of being recommended by the datasheet for DCVDD supplies that take longer than 2mS to rise. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Simplify with dev_err_probe()

2020-09-30T15:24:57Z

Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and also it prints the error value. Signed-off-by: Krzysztof Kozlowski Acked-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Improve handling of regulator unbinding

2020-08-13T06:50:54Z

The current unbinding process for Madera has some issues. The trouble is runtime PM is disabled as the first step of the process, but some of the drivers release IRQs causing regmap IRQ to issue a runtime get which fails. To allow runtime PM to remain enabled during mfd_remove_devices, the DCVDD regulator must remain available. In the case of external DCVDD's this is simple, the regulator can simply be disabled/put after the call to mfd_remove_devices. However, in the case of an internally supplied DCVDD the regulator needs to be released after the other MFD children depending on it. Use the new MFD mfd_remove_devices_late functionality to split the DCVDD regulator off from the other drivers. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Fix minor formatting issues

2020-06-18T10:23:15Z

The mfd_cell structures inconsistently use commas on single entries in the table, make this consistent by always using a comma. Also remove an extra blank line. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Allow more time for hardware reset

2020-01-24T07:33:58Z

Both manual and power on resets have a brief period where the chip will not be accessible immediately afterwards. Extend the time allowed for this from a minimum of 1mS to 2mS based on newer evaluation of the hardware and ensure this reset happens in all reset conditions. Whilst making the change also remove the redundant NULL checks in the reset functions as the GPIO functions already check for this. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Wait for boot done before accessing any other registers

2020-01-24T07:33:58Z

It is advised to wait for the boot done bit to be set before reading any other register, update the driver to respect this. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Add support for requesting the supply clocks

2019-11-11T08:45:03Z

Add the ability to get the clock for each clock input pin of the chip and enable MCLK2 since that is expected to be a permanently enabled 32kHz clock. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones

mfd: madera: Fixup SPDX headers

2019-07-02T11:11:31Z

GPL-2.0-only is the preferred way of expressing v2 of the GPL, so switch to that. Remove some redundant copyright notices and correct some instances where the wrong comment type has been used in header files. Signed-off-by: Charles Keepax Signed-off-by: Lee Jones