kernel/drivers/message/fusion/mptlan.c, branch linux-4.16.y

net: use core MTU range checking in misc drivers

2016-10-20T18:51:10Z

firewire-net: - set min/max_mtu - remove fwnet_change_mtu nes: - set max_mtu - clean up nes_netdev_change_mtu xpnet: - set min/max_mtu - remove xpnet_dev_change_mtu hippi: - set min/max_mtu - remove hippi_change_mtu batman-adv: - set max_mtu - remove batadv_interface_change_mtu - initialization is a little async, not 100% certain that max_mtu is set in the optimal place, don't have hardware to test with rionet: - set min/max_mtu - remove rionet_change_mtu slip: - set min/max_mtu - streamline sl_change_mtu um/net_kern: - remove pointless ndo_change_mtu hsi/clients/ssi_protocol: - use core MTU range checking - remove now redundant ssip_pn_set_mtu ipoib: - set a default max MTU value - Note: ipoib's actual max MTU can vary, depending on if the device is in connected mode or not, so we'll just set the max_mtu value to the max possible, and let the ndo_change_mtu function continue to validate any new MTU change requests with checks for CM or not. Note that ipoib has no min_mtu set, and thus, the network core's mtu > 0 check is the only lower bounds here. mptlan: - use net core MTU range checking - remove now redundant mpt_lan_change_mtu fddi: - min_mtu = 21, max_mtu = 4470 - remove now redundant fddi_change_mtu (including export) fjes: - min_mtu = 8192, max_mtu = 65536 - The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to get past the core net MTU range checks so fjes_change_mtu can validate a new MTU against what it supports (see fjes_support_mtu in fjes_hw.c) hsr: - min_mtu = 0 (calls ether_setup, max_mtu is 1500) f_phonet: - min_mtu = 6, max_mtu = 65541 u_ether: - min_mtu = 14, max_mtu = 15412 phonet/pep-gprs: - min_mtu = 576, max_mtu = 65530 - remove redundant gprs_set_mtu CC: netdev@vger.kernel.org CC: linux-rdma@vger.kernel.org CC: Stefan Richter CC: Faisal Latif CC: linux-rdma@vger.kernel.org CC: Cliff Whickman CC: Robin Holt CC: Jes Sorensen CC: Marek Lindner CC: Simon Wunderlich CC: Antonio Quartulli CC: Sathya Prakash CC: Chaitra P B CC: Suganath Prabu Subramani CC: MPT-FusionLinux.pdl@broadcom.com CC: Sebastian Reichel CC: Felipe Balbi CC: Arvid Brodin CC: Remi Denis-Courmont Signed-off-by: Jarod Wilson Signed-off-by: David S. Miller

treewide: replace dev->trans_start update with helper

2016-05-04T18:16:49Z

Replace all trans_start updates with netif_trans_update helper. change was done via spatch: struct net_device *d; @@ - d->trans_start = jiffies + netif_trans_update(d) Compile tested only. Cc: user-mode-linux-devel@lists.sourceforge.net Cc: linux-xtensa@linux-xtensa.org Cc: linux1394-devel@lists.sourceforge.net Cc: linux-rdma@vger.kernel.org Cc: netdev@vger.kernel.org Cc: MPT-FusionLinux.pdl@broadcom.com Cc: linux-scsi@vger.kernel.org Cc: linux-can@vger.kernel.org Cc: linux-parisc@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-hams@vger.kernel.org Cc: linux-usb@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: linux-s390@vger.kernel.org Cc: devel@driverdev.osuosl.org Cc: b.a.t.m.a.n@lists.open-mesh.org Cc: linux-bluetooth@vger.kernel.org Signed-off-by: Florian Westphal Acked-by: Felipe Balbi Acked-by: Mugunthan V N Acked-by: Antonio Quartulli Signed-off-by: David S. Miller

[SCSI] mptfusion: Extra debug prints added relavent to Device missing delay error handling

2010-07-28T14:07:47Z

Adding function name in original debug prints and few more debug prints are added. Signed-off-by: Kashyap Desai Cc: Stable Tree Signed-off-by: James Bottomley

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

2010-03-30T13:02:32Z

percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo Guess-its-ok-by: Christoph Lameter Cc: Ingo Molnar Cc: Lee Schermerhorn

headers: remove sched.h from interrupt.h

2009-10-11T18:20:58Z

After m68k's task_thread_info() doesn't refer to current, it's possible to remove sched.h from interrupt.h and not break m68k! Many thanks to Heiko Carstens for allowing this. Signed-off-by: Alexey Dobriyan

net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functions

2009-07-06T02:16:04Z

This patch is the result of an automatic spatch transformation to convert all ndo_start_xmit() return values of 0 to NETDEV_TX_OK. Some occurences are missed by the automatic conversion, those will be handled in a seperate patch. Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller

net: use symbolic values for ndo_start_xmit() return codes

2009-06-13T08:18:50Z

Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively. 0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases where its in direct proximity to one of the other values. Signed-off-by: Patrick McHardy Signed-off-by: David S. Miller

fusion: convert devices to new API

2009-01-08T02:04:45Z

Convert to net_device_ops and internal net_device_stats Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller

mptlan: Kill directly reference of netdev->priv

2008-12-04T05:13:37Z

Simply replace netdev->priv with netdev_priv(). Signed-off-by: Wang Chen Signed-off-by: David S. Miller

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

2008-11-11T23:43:02Z

Conflicts: drivers/message/fusion/mptlan.c drivers/net/sfc/ethtool.c net/mac80211/debugfs_sta.c