kernel/drivers/memory/tegra, branch linux-4.17.y

memory: tegra: Apply interrupts mask per SoC

2018-08-03T05:47:58Z

[ Upstream commit 1c74d5c0de0c2cc29fef97a19251da2ad6f579bd ] Currently we are enabling handling of interrupts specific to Tegra124+ which happen to overlap with previous generations. Let's specify interrupts mask per SoC generation for consistency and in a preparation of squashing of Tegra20 driver into the common one that will enable handling of GART faults which may be undesirable by newer generations. Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

memory: tegra: Do not handle spurious interrupts

2018-08-03T05:47:58Z

[ Upstream commit bf3fbdfbec947cdd04b2f2c4bce11534c8786eee ] The ISR reads interrupts-enable mask, but doesn't utilize it. Apply the mask to the interrupt status and don't handle interrupts that MC driver haven't asked for. Kernel would disable spurious MC IRQ and report the error. This would happen only in a case of a very severe bug. Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

memory: tegra: Create SMMU display groups

2017-12-15T09:12:32Z

Create SMMU display groups for Tegra30, Tegra114, Tegra124 and Tegra210. This allows the display controllers on these devices to share the same IOMMU domain using the standard IOMMU group mechanism. Signed-off-by: Thierry Reding

memory: tegra: Add Tegra186 support

2017-12-13T11:58:21Z

The memory controller found on Tegra186 is different in some respects to its predecessors. Most notably it no longer implements an SMMU, but does assign ARM SMMU stream IDs for each memory client instead. Provide a driver that programs these registers so that memory clients can translate addresses via the ARM SMMU. Signed-off-by: Thierry Reding

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55Z

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

memory: tegra: Add a missing 'of_node_put()' call

2017-01-25T06:57:13Z

If 'of_find_device_by_node()' fails, an 'of_node_put()' call is missing in the error handling path. Fix it by reordering the code. While at it, remove some empty lines in a more or less similar construction a few lines below. Signed-off-by: Christophe JAILLET Signed-off-by: Thierry Reding

memory: tegra: mc: Add missing of_node_put()

2016-06-14T09:39:39Z

for_each_child_of_node() performs an of_node_get() on each iteration, so to break out of the loop an of_node_put() is required. Found using Coccinelle. The semantic patch used for this is as follows: // @@ expression e; local idexpression n; @@ for_each_child_of_node(..., n) { ... when != of_node_put(n) when != e = n ( return n; | + of_node_put(n); ? return ...; ) ... } // Signed-off-by: Amitoj Kaur Chawla Signed-off-by: Thierry Reding

memory: tegra: Delete unneeded of_node_put()

2016-06-14T09:39:39Z

for_each_child_of_node() performs an of_node_put() on each iteration, so putting an of_node_put() before a continue results in a double put. The semantic match that finds this problem is as follows (http://coccinelle.lip6.fr): // @@ expression root,e; local idexpression child; iterator name for_each_child_of_node; @@ for_each_child_of_node(root, child) { ... when != of_node_get(child) * of_node_put(child); ... * continue; } // Signed-off-by: Julia Lawall Signed-off-by: Thierry Reding

memory: tegra: tegra124-emc: Add missing of_node_put()

2016-06-14T09:39:38Z

memory/tegra: Add number of TLB lines for Tegra124

2015-12-14T15:11:35Z

Tegra124 was accidentally left out when the number of TLB lines was parameterized in commit 11cec15bf3fb ("iommu/tegra-smmu: Parameterize number of TLB lines"). Fortunately this doesn't cause any noticeable regressions upstream, presumably because there aren't any use-cases that exercise enough pressure on the SMMU. But it is a regression nonetheless, so let's fix it. Fixes: 11cec15bf3fb ("iommu/tegra-smmu: Parameterize number of TLB lines") Signed-off-by: Vince Hsu Signed-off-by: Tomasz Figa [treding@nvidia.com: extract from unrelated patch] Signed-off-by: Thierry Reding