kernel/drivers/media/usb/go7007, branch linux-6.9.y

media: go7007: fix a memleak in go7007_load_encoder

2024-02-28T15:00:33Z

In go7007_load_encoder, bounce(i.e. go->boot_fw), is allocated without a deallocation thereafter. After the following call chain: saa7134_go7007_init |-> go7007_boot_encoder |-> go7007_load_encoder |-> kfree(go) go is freed and thus bounce is leaked. Fixes: 95ef39403f89 ("[media] go7007: remember boot firmware") Signed-off-by: Zhipeng Lu Signed-off-by: Hans Verkuil

media: go7007: add check of return value of go7007_read_addr()

2024-02-16T10:46:33Z

If go7007_read_addr() returns error channel is not assigned a value. In this case go to allocfail. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 866b8695d67e ("Staging: add the go7007 video driver") Signed-off-by: Daniil Dulov Signed-off-by: Hans Verkuil

media: v4l: Use correct dependency for camera sensor drivers

2023-09-14T10:38:17Z

The Kconfig option that enables compiling camera sensor drivers is VIDEO_CAMERA_SENSOR rather than MEDIA_CAMERA_SUPPORT as it was previously. Fix this. Also select VIDEO_OV7670 for marvell platform drivers only if MEDIA_SUBDRV_AUTOSELECT and VIDEO_CAMERA_SENSOR are enabled. Reported-by: Randy Dunlap Fixes: 7d3c7d2a2914 ("media: i2c: Add a camera sensor top level menu") Signed-off-by: Sakari Ailus Signed-off-by: Hans Verkuil

media: go7007: Remove redundant if statement

2023-08-10T05:58:32Z

The if statement that compares msgs[i].len != 3 is always false because it is in a code block where msg[i].len is equal to 3. The check is redundant and can be removed. As detected by cppcheck static analysis: drivers/media/usb/go7007/go7007-i2c.c:168:20: warning: Opposite inner 'if' condition leads to a dead code block. [oppositeInnerCondition] Link: https://lore.kernel.org/linux-media/20230727174007.635572-1-colin.i.king@gmail.com Fixes: 866b8695d67e ("Staging: add the go7007 video driver") Signed-off-by: Colin Ian King Signed-off-by: Mauro Carvalho Chehab

media: Switch i2c drivers back to use .probe()

2023-05-25T14:21:21Z

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type"), all drivers being converted to .probe_new() and then commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert back to (the new) .probe() to be able to eventually drop .probe_new() from struct i2c_driver. Signed-off-by: Uwe Kleine-König Signed-off-by: Hans Verkuil

media: go7007: don't modify q->streaming

2023-02-06T08:01:05Z

The streaming state is maintained by the vb2 core, so drivers must never change it themselves. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab

media: usb: go7007: s2250-board: Convert to i2c's .probe_new()

2022-11-21T10:04:46Z

The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by: Uwe Kleine-König Signed-off-by: Hans Verkuil

i2c: Make remove callback return void

2022-08-16T10:46:26Z

The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin Reviewed-by: Jeremy Kerr Reviewed-by: Benjamin Mugnier Reviewed-by: Javier Martinez Canillas Reviewed-by: Crt Mori Reviewed-by: Heikki Krogerus Acked-by: Greg Kroah-Hartman Acked-by: Marek Behún # for leds-turris-omnia Acked-by: Andy Shevchenko Reviewed-by: Petr Machata # for mlxsw Reviewed-by: Maximilian Luz # for surface3_power Acked-by: Srinivas Pandruvada # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil # for media/* + staging/media/* Acked-by: Miguel Ojeda # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli # for versaclock5 Reviewed-by: Ajay Gupta # for ucsi_ccg Acked-by: Jonathan Cameron # for iio Acked-by: Peter Rosin # for i2c-mux-*, max9860 Acked-by: Adrien Grassein # for lontium-lt8912b Reviewed-by: Jean Delvare # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard # for IPMI Reviewed-by: Vladimir Oltean Acked-by: Dmitry Torokhov Acked-by: Sebastian Reichel # for drivers/power Acked-by: Krzysztof Hałasa Signed-off-by: Uwe Kleine-König Signed-off-by: Wolfram Sang

media: usb: go7007: s2250-board: fix leak in probe()

2022-02-22T08:41:12Z

Call i2c_unregister_device(audio) on this error path. Fixes: d3b2ccd9e307 ("[media] s2250: convert to the control framework") Signed-off-by: Dan Carpenter Signed-off-by: Hans Verkuil

media: go7007: Constify static struct snd_device_ops

2022-02-22T08:41:11Z

The only usage of go7007_snd_device_ops is to pass its address to snd_device_new() which takes a pointer to const struct snd_device_ops. Make it const to allow the compiler to put it in read-only memory. Signed-off-by: Rikard Falkeborn Signed-off-by: Hans Verkuil