kernel/drivers/media/rc/serial_ir.c, branch linux-6.9.y

media: rc: fix timeout handling after switch to microsecond durations

2021-01-11T11:58:44Z

Commit 528222d853f92 ("media: rc: harmonize infrared durations to microseconds") missed to switch some timeout calculations from nanoseconds to microseconds. This resulted in spurious key_up+key_down events at the last scancode if the rc device uses a long timeout (eg 100ms on nuvoton-cir) as the device timeout wasn't properly accounted for in the keyup timeout calculation. Fix this by applying the proper conversion functions. Cc: stable@vger.kernel.org Fixes: 528222d853f92 ("media: rc: harmonize infrared durations to microseconds") Signed-off-by: Matthias Reichl Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: rc: harmonize infrared durations to microseconds

2020-09-03T14:18:55Z

rc-core kapi uses nanoseconds for infrared durations for receiving, and microseconds for sending. The uapi already uses microseconds for both, so this patch does not change the uapi. Infrared durations do not need nanosecond resolution. IR protocols do not have durations shorter than about 100 microseconds. Some IR hardware offers 250 microseconds resolution, which is sufficient for most protocols. Better hardware has 50 microsecond resolution and is enough for every protocol I am aware off. Unify on microseconds everywhere. This simplifies the code since less conversion between microseconds and nanoseconds needs to be done. This affects: - rx_resolution member of struct rc_dev - timeout member of struct rc_dev - duration member in struct ir_raw_event Cc: "Bruno Prémont" Cc: Hans Verkuil Cc: Maxim Levitsky Cc: Patrick Lerda Cc: Kevin Hilman Cc: Neil Armstrong Cc: Jerome Brunet Cc: Martin Blumenstingl Cc: Sean Wang Cc: Matthias Brugger Cc: Patrice Chotard Cc: Maxime Ripard Cc: Chen-Yu Tsai Cc: "David Härdeman" Cc: Benjamin Valentin Cc: Antti Palosaari Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: serial_ir: use the right type for a dma address

2020-09-03T09:11:40Z

As warned by smatch: drivers/media/rc/serial_ir.c:550 serial_ir_probe() warn: should '8 << ioshift' be a 64 bit type? the "8" constant should be unsigned long. Signed-off-by: Mauro Carvalho Chehab

media: serial_ir: change "ignoring spike" to debug level

2020-01-03T15:29:33Z

At least on my system with a self-made IR receiver, my kernel log is filled with: serial_ir serial_ir.0: ignoring spike: 1 1 1419988034627194ns 1419956080709377ns These messages happen at random and do not prevent the receiver from working. Also I cannot change the features of the IC, therefore they are not useful. Probably they are not useful at all. However they fill the console, they accumulate and fill the dmesg log, by doing this, they prevent me from seeing important message. Signed-off-by: Bodo Eggert <7eggert@gmx.de> Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

2019-05-30T18:26:37Z

Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Allison Randal Reviewed-by: Richard Fontana Reviewed-by: Kate Stewart Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman

media: serial_ir: Fix use-after-free in serial_ir_init_module

2019-03-19T20:46:20Z

Syzkaller report this: BUG: KASAN: use-after-free in sysfs_remove_file_ns+0x5f/0x70 fs/sysfs/file.c:468 Read of size 8 at addr ffff8881dc7ae030 by task syz-executor.0/6249 CPU: 1 PID: 6249 Comm: syz-executor.0 Not tainted 5.0.0-rc8+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xfa/0x1ce lib/dump_stack.c:113 print_address_description+0x65/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 ? 0xffffffffc1728000 sysfs_remove_file_ns+0x5f/0x70 fs/sysfs/file.c:468 sysfs_remove_file include/linux/sysfs.h:519 [inline] driver_remove_file+0x40/0x50 drivers/base/driver.c:122 remove_bind_files drivers/base/bus.c:585 [inline] bus_remove_driver+0x186/0x220 drivers/base/bus.c:725 driver_unregister+0x6c/0xa0 drivers/base/driver.c:197 serial_ir_init_module+0x169/0x1000 [serial_ir] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x462e99 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f9450132c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00007f9450132c70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f94501336bc R13: 00000000004bcefa R14: 00000000006f6fb0 R15: 0000000000000004 Allocated by task 6249: set_track mm/kasan/common.c:85 [inline] __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:495 kmalloc include/linux/slab.h:545 [inline] kzalloc include/linux/slab.h:740 [inline] bus_add_driver+0xc0/0x610 drivers/base/bus.c:651 driver_register+0x1bb/0x3f0 drivers/base/driver.c:170 serial_ir_init_module+0xe8/0x1000 [serial_ir] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 6249: set_track mm/kasan/common.c:85 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:457 slab_free_hook mm/slub.c:1430 [inline] slab_free_freelist_hook mm/slub.c:1457 [inline] slab_free mm/slub.c:3005 [inline] kfree+0xe1/0x270 mm/slub.c:3957 kobject_cleanup lib/kobject.c:662 [inline] kobject_release lib/kobject.c:691 [inline] kref_put include/linux/kref.h:67 [inline] kobject_put+0x146/0x240 lib/kobject.c:708 bus_remove_driver+0x10e/0x220 drivers/base/bus.c:732 driver_unregister+0x6c/0xa0 drivers/base/driver.c:197 serial_ir_init_module+0x14c/0x1000 [serial_ir] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8881dc7ae000 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 48 bytes inside of 256-byte region [ffff8881dc7ae000, ffff8881dc7ae100) The buggy address belongs to the page: page:ffffea000771eb80 count:1 mapcount:0 mapping:ffff8881f6c02e00 index:0x0 flags: 0x2fffc0000000200(slab) raw: 02fffc0000000200 ffffea0007d14800 0000000400000002 ffff8881f6c02e00 raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881dc7adf00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8881dc7adf80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff8881dc7ae000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881dc7ae080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc7ae100: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00 There are already cleanup handlings in serial_ir_init error path, no need to call serial_ir_exit do it again in serial_ir_init_module, otherwise will trigger a use-after-free issue. Fixes: fa5dc29c1fcc ("[media] lirc_serial: move out of staging and rename to serial_ir") Reported-by: Hulk Robot Signed-off-by: YueHaibing Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: rc: Remove init_ir_raw_event and DEFINE_IR_RAW_EVENT macros

2018-10-04T18:22:27Z

This can be done with c99 initializers, which makes the code cleaner and more transparent. It does require gcc 4.6, because of this bug in earlier versions: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676 Since commit cafa0010cd51 ("Raise the minimum required gcc version to 4.6"), this is the case. Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: serial_ir: Convert timers to use timer_setup()

2017-10-27T15:38:54Z

In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Cc: Mauro Carvalho Chehab Signed-off-by: Kees Cook Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: serial_ir: fix tx timing calculation on 32-bit

2017-08-31T09:36:42Z

Move the calculation to where it is needed, so the result doesn't need to be stored in the device struct. Signed-off-by: Sean Young Signed-off-by: Mauro Carvalho Chehab

media: rc: rename RC_TYPE_* to RC_PROTO_* and RC_BIT_* to RC_PROTO_BIT_*

2017-08-20T14:02:48Z

RC_TYPE is confusing and it's just the protocol. So rename it. Suggested-by: Hans Verkuil Signed-off-by: Sean Young Acked-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab