kernel/drivers/input/joystick/Kconfig, branch linux-4.16.y

Input: add support for PlayStation 1/2 joypads connected via SPI

2017-05-10T21:35:48Z

PlayStation 1/2 joypads can be connected directly to the SPI interface. Signed-off-by: Tomohiro Yoshidomi Acked-by: David Herrmann Signed-off-by: Dmitry Torokhov

drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE

2015-10-02T01:42:35Z

It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in vmlinux. Cc: Fengguang Wu Cc: yalin wang Cc: Dmitry Torokhov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

Input: add Austria Microsystem AS5011 joystick driver

2011-01-10T19:01:43Z

This is driver for EasyPoint AS5011 2 axis joystick chip. This chip is plugged on an I2C bus. Tested on ARM processor (i.MX27). Signed-off-by: Fabien Marteau Signed-off-by: Dmitry Torokhov

Input: gamecon - add rumble support for N64 pads

2010-02-22T06:09:43Z

Add force-feedback support for N64 pads with rumble pak accessory installed. Actually we do not check for the presence of rumble pad but simply assume it is installed and expect the device to ignore FF commands if rumble pak is missing. Signed-off-by: Scott Moreau Signed-off-by: Dmitry Torokhov

Input: add support for Maple controller as a joystick

2008-12-30T08:58:05Z

Add support for the SEGA Dreamcast Maple controller as a joystick Signed-off-by: Adrian McMenamin Signed-off-by: Dmitry Torokhov

Input: add joystick driver for Walkera WK-0701 RC transmitter

2008-11-19T21:55:40Z

Signed-off-by: Peter Popovec Signed-off-by: Dmitry Torokhov

Input: add Zhen Hua driver

2008-04-15T17:26:52Z

This is a driver for Zhen Hua PPM-4CH RC transmitter (commonly used in cheap Ready To Fly RC helicopters by Walkera) which using "Zhen Hua 5-byte protocol" for using them as a four axis joystick via serial port. Transmitter connected to serial port (19200 8N1) sending periodically 5 bytes where first byte is for synchronization and next four bytes are values of axis. Signed-off-by: Martin Kebert Signed-off-by: Jiri Kosina Signed-off-by: Dmitry Torokhov

Input: xpad - fix dependancy on LEDS class

2007-09-28T22:38:12Z

Input: xpad - fix dependancy on LEDS class The driver can not be built-in when LEDS class is a module. Signed-off-by: Dmitry Torokhov Signed-off-by: Linus Torvalds

Input: xpad - add support for leds on xbox 360 pad

2007-07-18T04:35:40Z

Export LEDs on Xbox360 pad via led subsystem as a single device in /sys/class/leds/xpad[0-9]+. Xbox360 pad has four leds, which form a circle. Unfortunately the leds can't be controlled independently and can only display a predefined set of patterns (for example one is turned on wile others are off or a rotating pattern - 1-2-3-4). To activate a pattern one needs to send a specific command to the device (see http://www.free60.org/wiki/Gamepad). Led subsystem allows us to set brightness, but there is nothing like brightness on this device. So brightness is actually interpreted as the command (only values between 0 and 14 are accepted). Signed-off-by: Jan Kratochvil Signed-off-by: Dmitry Torokhov

Input: xpad - add Xbox360 gamepad rumble support

2007-07-10T04:35:15Z

Implementation is using force feedback support for memoryless devices. Signed-off-by: Jan Kratochvil Signed-off-by: Dmitry Torokhov